Search results

I installed Vplug to get Tandberg... Is that still working?

I installed oscam.ipk plugin on my receiver. how do I go about updating to a newer oscam? do i need to start this process with the .deb or .ipk file again? I have a Vu Duo 4K ... which oscam should I update and how? which one of these is the correct one...

I am not sure why dream multimedia is not releasing the new DVB-s2x triple tuner but even if that’s released I don’t think it will support DVB-S2 16/32 ASPK… Does anyone in this forum managed to get the TBS tuner 5925 or 5922 working on the DM 900? What image did you use? Tks…

Is there a way to get powervu working on the octagon receivers? Off course the more powerful units...The dual core or the 4k? Which emulator works for it? Tks...

Is Oscam the only emulation that works for powervu?

I have a perfectly working DM 800 SE using oscam for powervu. I am planning to get the DM900 but I would like to know if this new receiver supports powervu without streamrelay using OSCAM emulation. I can't seem to find anywhere if this DM900 supports DES Decryption... Tks,

Guys, I have the DM 800 SE A8P Sim and so far I installed Tytus Newnigma and works great ... Tytus image does not have the drives for the TBS 5925 card so that I can enable 16/32 APSK. Other images more recent of OpenATV, OpenPLI, satdreamgr already have those drivers support. Can I install...

Does anyone know if the new dreambox works with oscam running powervu? If so...which oscam file?

I have the GTX 580 and 960 and both can't create chains using version 2. I am successful in version 1 as I can easily crate chains but in version 2 the speed stays stuck at 0 kcw/sec. I do connect to the server and works perfectly identifying the card but i can't create chains. Any idea what...

I have some general questions on the rainbow table Why does version 1.23f not allow to create chains for ffh nd 30k? Which card works fastest to create chains gtx 780 or gtx 980?

SES 1 4020 H 30000 stopped sending patterns ...is anyone able to get the new ECM key?

I installed Newnigma-4.0-2016-01-02 backup by @tytus 56 dm800se sim a8p... But after installation the web interface shows up but does not open anything... I have oscam working properly on powervu but can't get the web interface to work. Anyone with the same problem?

Where can I find the unpatched OSCAM file? Everything I see in the site refers to the patched version ...

I do recall seeing somewhere a line command for the scripts in OSCAM that extracted all the powervu channels info from the receiver. Can someone please post how can I run a script in OSCAM that extracts all powervu channels so that I can create a softcam file based on the new oscam emu format...

with the DM 800 SE A8P am I able to load the openpli mastag image for dm 800 Se? Looks to me that this image is for the original DM receivers... but with A8P sim does it make it safe to load this file from Mastag openPLI-4?

What is the difference between the ALPS 801A tuner and the regular single input tuner that comes in most DM receiver? are both DVB-S2? which one has a more sensitive tuner? ALPS or the regular single input tuner?

Are there any advantages in having the A8P chip on the clone dreambox? I can tell that the newer unit offers 2 USB ports in the back. But other than a8p I don't see any other differences. Can someone confirm? Which model has better support? Ssl84? Or Sim A8P? Thanks,

I am looking to buy the version 2 original dreambox... Is anyone in the forum using them to receive powervu? How do i know if the files here are for the original or clone?

I read that OSCAM dupports Biss from the softcam.key file in Var/Keys. How do I properly load configure the keys? BISS/ConstCW config =================== Syntax for keys in SoftCam.Key: (key number can be '00' or '01') F <service id><ecm pid> <key number> <key> Example: service id: 2222...

I installed openPLI4.0 image on the solo SE V2. Now I need to setup OSCAM. There are so many out there... can someone please let me know which OSCAM I should be installing on this receiver? during the installation of openPLI it asked for OSCAM to be downloaded so I selected yes... after I...