Ferguson HD [Main Chat]

E

enrydgl

Registered
Messages
16
kanetaker2010 said:
If the card is a tiger nagra you can't use it on both boxs, because there aren't nagra support for them.
Click to expand...

Yes, my card is a Tiger nagra but... I have downloaded the PDF guides (first page/post number 8 in this forum) and in Newcamd Server/Cccam Home Server appears "nagra" like Smartcard option. How is possible? It's strange or it's an error.

However.. I have these question...
1 - Can I used 150 Ariva like client DVB-T (tiger nagra) in Home B and Amiko Alien2 like server DVB-T (with nagra smartcard) in home A (no local network but by router/modem)?
2 - Ariva like client accept c*ine e n*ine (ne*ca*d protocol and c*c*am protocol)?
3 - Like Bugs... Ariva 150 HD is good decoder like fw custom?

Thank very much.
Bye.
 
M

MICKAH

Registered
Messages
47
Guys, the last version firmware, it has a problem with Newcmd, if you are using a nline and you start watching a FTA chan, the box drops its connection to the server as, when on a FTA chan, there isnt anything ecm requests happening, only on encrypted chans
 
F

FRANCIS67

Registered
Messages
3
Hi I have the message ASH on my Combo 150 since I have update with 1.91patched. Someone can tell me exactly how I can recover that problem (I had the official FW 1.91 and thought that I could apply what Mickah wrote but that goes wrong).

Thanks a lot to read you

Francis
 
M

MICKAH

Registered
Messages
47
Hi mate, on page one there is the programme to fix this, eprom fix, this will reflash the box back, you will need the original firmware back on it to and a rs232 cable, have seen few do this and this will bring them back

Just of note, the V1.19 firmware, there is an issue with it, a few folks have reported the ASH problem after flashing the box with it or using it for a while, the firmware has a issue with the sharing side, CCAM is glitchy at best, NEWCAMD, the box works fine on a pay chan, but if you watch a FTA chan for about 10 mins and go to a pay chan, it wont clear, its the like the box stops taking ecms and then wont engage when it does and clear chans, this isnt the case on the older firmware as I have got this tested using the same line and it works, lastly youtube, youporn dont work proper on this either, "No Network" or videos wont play, hopefully the new firmware address this issue as it renders the sharing on this box as useless,
 
S

sdssss

Registered
Messages
3
hi all!! since i am new with this receiver (250combo)the question that i will ask may sound silly so forgive me.. if someone uses the original firmware and not the patched one is it possible to use an n-line or a c-line by unlocking a secret menu or something like that.thanks
 
I

Iba

Registered
Messages
14
Hi

Im using the 1.18 patched firmware and i have an nline.

I flashed the box and did a factory reset.

But im having trouble in the newcamclient settings - I cant enter my password and im not sure i i should be using the number 10000 or 8000.

Also I can get an IP address but on the other hand i cannot connect to network. In other words, i can connect to daily motion but i cant get the weather.

Can anyone help please?

Thanks

Iba
 
I

Iba

Registered
Messages
14
Ok guys

Ive got my nline up and running on 1.18 version.

However, when i switch from a fta channel to a non-fta, my channel is scrambled and i have to turn the box off and on.

So whats the consensus, should i stick with the 1.18 or go for the 1.20?

Also anyone got a channel list to go with the 1.18 or the 1.20 please?

Thanks

Iba
 
S

Serafeim

Registered
Messages
202
What is the newest software for model 210 combo (official and patch)? And one more question: how can i enter - edit biss keys?
 
JAKITAKI

JAKITAKI

Super VIP
Messages
9,214
Serafeim said:
What is the newest software for model 210 combo (official and patch)?
Click to expand...

2.18B4

Serafeim said:
And one more question: how can i enter - edit biss keys?
Click to expand...

keydb ****> http://www.sat-universe.com/attachment.php?attachmentid=319702&d=1348547244

Snap2.jpg


typed name must be identical to the name in the list of channels

Snap3.jpg
 
I

Iba

Registered
Messages
14
Ariva 250

Ok guys

Ive got my nline up and running on 1.18 version on tha Ariva 250

However, when i switch from a fta channel to a non-fta, my channel is scrambled and i have to turn the box off and on.

So whats the consensus, should i stick with the 1.18 or go for the 1.20?

Also anyone got a channel list to go with the 1.18 or the 1.20 please?

Thanks

Iba
 
JAKITAKI

JAKITAKI

Super VIP
Messages
9,214
Serafeim said:
Thank you.
Is it possible to enter - edit them using the remote control?
Click to expand...

so, you're in the menu > system settings > system tv > press the red button > choose the encoding system ;)

if, in the system TV, you do not have a red button, enter the code 7799
 
JAKITAKI

JAKITAKI

Super VIP
Messages
9,214
Iba said:
Ok guys

Ive got my nline up and running on 1.18 version on tha Ariva 250

However, when i switch from a fta channel to a non-fta, my channel is scrambled and i have to turn the box off and on.

So whats the consensus, should i stick with the 1.18 or go for the 1.20?

Also anyone got a channel list to go with the 1.18 or the 1.20 please?

Thanks

Iba
Click to expand...

If you are using newcamd protocol, its performance is improved in version 1.19B1

I suggest to upload the latest software version 1.20B1

- channel list, you can upload the older version ;)
 
You must log in or register to reply here.
Top