Qviart DUAL Experimental Receiver

[kamacnik1]

OpenPli 8.3 - OK
Both with ncam 13.7 and Oscam Icam by Kitte888 runing smoothly
On path menu-setup-system-customize You have to set 3 values to work properly
- Include ECM in http stream - NO
- Descramble sending http streams - YES
- Descramble receiving http streams - NO
And in oscam.conf You can put this

[streamrelay]
stream_relay_enabled = 1
stream_emm_enabled = 5
stream_relay_ctab = 098D,09CD

Cobraliberosat dont have installed , so no testing

OK, i have Octagon SF8008 , but both Octagon and Qviart run under same processor , there should't be any major differences

 

[kegnkiwi]

OpenPli 8.3 - OK
Both with ncam 13.7 and Oscam Icam by Kitte888 runing smoothly
On path menu-setup-system-customize You have to set 3 values to work properly
- Include ECM in http stream - NO
- Descramble sending http streams - YES
- Descramble receiving http streams - NO
And in oscam.conf You can put this

[streamrelay]
stream_relay_enabled = 1
stream_emm_enabled = 5
stream_relay_ctab = 098D,09CD

Cobraliberosat dont have installed , so no testing

OK, i have Octagon SF8008 , but both Octagon and Qviart run under same processor , there should't be any major differences

Thanks for your information i also have cobraliberosat on solo 4k with the same configurations and it also clears sky de.

 

[kamacnik1]

Just out off curiosity I did install newest Cobraliberosat image , and with this configuration mentioned above everything is OK , running smoothly with ncam 13,7

 

[kegnkiwi]

Just out off curiosity I did install newest Cobraliberosat image , and with this configuration mentioned above everything is OK , running smoothly with ncam 13,7

That's intersting would you send me over how you installed ncam 13.7 for me please. I used the demonstat panel to install ncam 13.7 and it seems to install but when activated it does not appear to be running in the webif. If you have the apk or a the telnet comand please post it. I may have a little time tomorrow to play. I do speak with the cobralibersat team and have told them about this on the dual. It would be great to get in working.

 

[kegnkiwi]

I have the ipk here, i will try and install it via ftp and see if it works this way.

 

[kamacnik1]

In fact very easy
First , You install from extensions dreamexplorer addon
Then ftp this ipk file in tmp , open dreamexplorer , find tmp folder and inside ipk You send earlier , click on them and choose - install this package
Later if restart gui isnt enough to make ncam work, then full restart should doo

Off course , and telnet command also do the same thing

opkg install --force-overwrite /tmp/*.ipk

 

[kegnkiwi]

In fact very easy
First , You install from extensions dreamexplorer addon
Then ftp this ipk file in tmp , open dreamexplorer , find tmp folder and inside ipk You send earlier , click on them and choose - install this package
Later if restart gui isnt enough to make ncam work, then full restart should doo

Yes its normally easy to do, i personally use dcc. send it to the temp file and install from the menu system on the box. At the same time ncam 13.7 installs via the dreamsat panel on most images but something seems incorrect on openpli and cobralibersat images. I'll test it and post back.

 

[viktor94]

hello all thank you for your advices .
Hopefully the update for the motorized dishes will come soon because we are not able to watch the channels .

 

[kegnkiwi]

hello all thank you for your advices .
Hopefully the update for the motorized dishes will come soon because we are not able to watch the channels .

Can i ask what update you are waiting on, is it for the android side?

 

[cretan]

OpenPli 8.3 - Tamam
Hem ncam 13.7 hem de Oscam Icam by Kitte888 sorunsuz çalışıyor
menu-setup-system-customize yolunda Düzgün çalışması için 3 değer ayarlamanız gerekir
- ECM'yi http akışına dahil et - HAYIR
- Http akışları gönderirken şifre çözme - EVET
- Http akışlarını almanın şifresini çöz - HAYIR
Ve oscam.conf'ta bunu koyabilirsiniz

[akış rölesi]
stream_relay_enabled = 1
stream_emm_enabled = 5
stream_relay_ctab = 098D,09CD

Cobraliberosat yüklü değil, bu nedenle test yok

Tamam, Octagon SF8008'e sahibim, ancak hem Octagon hem de Qviart aynı işlemci altında çalışıyor, büyük farklar olmamalı

I did exactly what you said, unfortunately openpli does not work...

 

[cretan]

Can i ask what update you are waiting on, is it for the android side?

Yes, we are waiting for new software for the android side, because the motor does not spin at all...

 

[kegnkiwi]

I did exactly what you said, unfortunately openpli does not work...

Try openatv or pure2 they both work.

 

[kegnkiwi]

Yes, we are waiting for new software for the android side, because the motor does not spin at all...

If you are on 1.06 yes there might be an issue with one or 2 sats but the motor does move. Have you tried installing ferrets latest channel list?

 

[cretan]

How should the engine settings be, I have 1 engine system, and there is a fixed system and they are connected to each other with diseqc, how should the settings be?

 

[cretan]

Try openatv or pure2 they both work.

It works on them, but does openPli work too?

 

[cretan]

Looking for Openvix backup or image?

 

[kegnkiwi]

It works on them, but does openPli work too?

If you have been following this thead i have said i have been unable to get it working on openpli or cobraliberosat images. I will have another play tomottow.

 

[kegnkiwi]

Looking for Openvix backup or image?

Openvix have not made an image for this box yet. Or should i say i have not seen an image from them.

 

[cokeaddict]

If you are on 1.06 yes there might be an issue with one or 2 sats but the motor does move.

It doesn't work with some motors / v-boxes.

Seems to be pot luck, as 2 v-boxes of the same "brand" but different models, 1 works and the other does not.

 

[kegnkiwi]

It doesn't work with some motors / v-boxes.

Seems to be pot luck, as 2 v-boxes of the same "brand" but different models, 1 works and the other does not.

That is a strange one.