I got booting process log
Many error scenarios
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}
2ND STAGE OK, build #76 (20100419)
0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
1.391 - load config
dCA: not existent, loading defaults
1.422 - config loaded.
* press to enter setup
OLED found!
BOOT #76(20100419)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 ([email protected]) (gcc version 4.4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from
When Flashing SSL84B
It can not find autoexec.bat
booting bahvior seems strange
Any one faced those error?
Many error scenarios
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}
2ND STAGE OK, build #76 (20100419)
0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
1.391 - load config
dCA: not existent, loading defaults
1.422 - config loaded.
* press
OLED found!
BOOT #76(20100419)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 ([email protected]) (gcc version 4.4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from
When Flashing SSL84B
It can not find autoexec.bat
booting bahvior seems strange
Any one faced those error?