Recent content by blue99

Powervu Home Edition finds some keys that are expired in North America from current EMM logs. Why are expired keys still in the stream?

I have a v8 super and upgraded to the latest firmware (V8_Super_V523). FTA chans work fine on this. Powervu chans give a 'Encrypted Program' message. Should this firmware autoroll the powervu keys or do I have to enter my own keys?

What's the offline ts tab in powervuemu for? When recording one powervu channel is it possible to record a second powervu chan on the same mux with the encryption still in place and then use offline ts in powervuemu to decrypt it later on?

Can someone re-upload TSReader V.2.8.47c? The link in the thread at http://www.sat-universe.com/showthread.php?t=284321 doesn't work and that thread is closed. Thanks.

I'm using dvbdream and can record multiple FTA chans on the same transponder. However, I can only record a single powervu chan when using the Powervu Emu plugin. If I try recording other chans on the same transponder they show up as a blank recording. Is there any way to record multiple chans on...

Is it possible to properly record powervu chans with dvbdream? I'm using powervu emu module v5 and can see the powervu chans being decrypted but when I try recording, the video is messed up & very choppy. If I try recording a non-encrypted chan it works fine.

Anyone using 125w notice signal degradation over the last few days? Channels that were in the 80s are now in the 50s or so. Satellites at other orbital locations are fine for me. Only issue is with this one.

Sometimes in a recording of 2 hrs I'll have one or two times where the video cuts out for a second or two. I want to find out what the cause of this is. It might be due to the signal strength dropping or something else. Is there someplace on the dm800 that logs the signal strength every second?

I'm using Blackhole 2.1.7 on my DM800 and sometimes the clock randomly changes time. I think maybe some transponder is updating it to the wrong time? I have to manually reset it back to the correct time using ntpdate. I suppose I could add a cronjob that routinely runs ntpdate, but is it...

Is there some place on the dm800 where you can find out signal strength for the current tuned transponder? I'm writing a simple script that will notify me if the signal strength drops below a certain %.

I tried recording 3 channels on a dm800 (all on same transponder) and the receiver became completely unresponsive (didn't respond to remote). The channel that it was tuned to was still working fine, but nothing else seemed to work. I looked at the recordings and there were lots of dropped frames...

I have a DM800, but I'm not sure if it's a clone or original. If I look at the info page, it lists the following. Is there a way to definitely confirm if this is an original or clone? Enigma Version: 2011-09-28-3.2 Image Version: Release SVN(098r6), 03-11-2011 The performance of this enigma...

Is there a low resource usage plugin that allows you to have a virtual remote control to control the dreambox from a PC? I've tried Dreambox Webcontrol, but it spikes up the cpu usage whenever using it. I just need something simple that provides the same functionality that the physical dreambox...

I have an external HDD connected using the USB port on the back. I've been able to initialize the drive and see that it's been formatted as ext3 and mounted on /media/hdd. Whenver I try to do a live recording, I get the green crash screen and it says to look at the log at /hdd, but there is no...

I have a DM800 with a ALPS BSBE2 tuner and am trying to get Ku band FTA chans. I have Lof set to Universal LNB, Diseqc mode to none, and Voltage Mode to polarization. There are some other settings like Increased Voltage, Tone Mode, and Tone Amplitude that I left as default (Yes, On, 800mV). Any...