urgent help needed on a humax5400 can some body help me out as when i switch on my humax 5400 i get 4 little lines that come on and a dot flashing all the time but i can not switch the stand buttom on what is the trouble please and how can i fix it i put in a new power unit but it did not help me i tryed a new channel list no luck then tryed new firmware no joy what do i do to it now thanks humaxman
urgent help needed on a humax5400
- Thread starter humaxman
- Start date
i think u did everything , did u try to change ur loader version or system id ? if not then try one more time send latest channel list still same then try to send original firmware with correct system id and loader ( with humax official software loader )
when u trying to load channels list or firmware use rare switch button for on off
when u trying to load channels list or firmware use rare switch button for on off
hi mogembo many thanks for your reply yes i did use rare switch button for on off
to load channels list or firmware no joy what is the best tool to use to upload the channel list and firmware and correct system id and loader ( with humax official software loader )
my loader is L1.37 hope this helps you sorry i not good at saying things as i had a stroke 10 years ago and not good in puting words togeather thanks humaxman
to load channels list or firmware no joy what is the best tool to use to upload the channel list and firmware and correct system id and loader ( with humax official software loader )
my loader is L1.37 hope this helps you sorry i not good at saying things as i had a stroke 10 years ago and not good in puting words togeather thanks humaxman
re Dots on front panel
Hi there,
If you have Loader L1.37 DO NOT TRY TO LOAD H2.08 LOADER!!
Download the latest Humax toolbox software and use the system ID tool to change your ID to ;
If you have IRCI-5400 on front panel use ID 00160000
If you have an 5400Z (chipped) model use ID 00160600
Use the ID tool to change the ID accordingly. If you write in software a wrong ID nothing wrong can happen to your box don't worry.
System ID : 00xx.0000 OAK-I PCB, MK2 tuner
System ID : 00xx.0400 OAK-I PCB, MK3 tuner
System ID : 00xx.0200 OAK-II PCB, MK2 tuner
System ID : 00xx.0600 OAK-II PCB, MK3 tuner
Check on your tuner ( physically ) and there should be a sticker which says MK2 tuner or MK3 tuner.
Check also on the mainboard if you have an OAK-I PCB or an OAK-II PCB
Use table above to get your proper Humax ID,
Example;
If you find you have an OAK-I PCB and an MK2 sticker , then your ID should be;
00160000
After that use a good channel editor , I suggest Setedit Oak V3 , (you can download it from the Setedit site).
Make sure that when you load a latest channel list in Setedit OAKV3,
before you transfer the data go in configuration and uncheck "When loading use personal LNB + menu settings" so you reset this area of your Humax as moist probably its corrupt.
Humax tend to corrupt this memory area and end up not being able to boot.
Take care my friend..:thum:
Hi there,
If you have Loader L1.37 DO NOT TRY TO LOAD H2.08 LOADER!!
Download the latest Humax toolbox software and use the system ID tool to change your ID to ;
If you have IRCI-5400 on front panel use ID 00160000
If you have an 5400Z (chipped) model use ID 00160600
Use the ID tool to change the ID accordingly. If you write in software a wrong ID nothing wrong can happen to your box don't worry.
System ID : 00xx.0000 OAK-I PCB, MK2 tuner
System ID : 00xx.0400 OAK-I PCB, MK3 tuner
System ID : 00xx.0200 OAK-II PCB, MK2 tuner
System ID : 00xx.0600 OAK-II PCB, MK3 tuner
Check on your tuner ( physically ) and there should be a sticker which says MK2 tuner or MK3 tuner.
Check also on the mainboard if you have an OAK-I PCB or an OAK-II PCB
Use table above to get your proper Humax ID,
Example;
If you find you have an OAK-I PCB and an MK2 sticker , then your ID should be;
00160000
After that use a good channel editor , I suggest Setedit Oak V3 , (you can download it from the Setedit site).
Make sure that when you load a latest channel list in Setedit OAKV3,
before you transfer the data go in configuration and uncheck "When loading use personal LNB + menu settings" so you reset this area of your Humax as moist probably its corrupt.
Humax tend to corrupt this memory area and end up not being able to boot.
Take care my friend..:thum:
che fatica
Registered
- Messages
- 8
can you explain how did you load a new channel list or a new fw ?
Have you read something on your screen tv during that download?
Please give as much info as possible to help you
hi maljam its not dots on the front of my humax 5400 its 4 little lines and the dot is under the two middle lines it looks like the clock is not set when its swiched on my standby buttom dont work and when you use the power switch on the back of the humax 5400 it dose not do any thing that is why i put in a new power supply as i thought that it was gone but no luck this is why i have come to this site for your urgent help i brought a new rs-232c cable but i get nothing to work with that so whats wrong with it and how can i put it right to get it in working order help me please thanks humaxman
Last edited:
hi i have just notice that on the front of my other humax5400 there is a red dot on the right hand side showing why the humax is in standby when you press it on by the standby buttom it gos off this humax 5400 wont go on is it on the motherboard or the power supply im got the trouble with thanks humaxman
re Humax
Humaxman, First of all Happy new year mate,
You said power supply was replaced with a good working one taken from another Humax 5400 so Power Supply is out of question.
When you turn it on from the back panel Power Switch, you should have momentarily the Loader version displayed on the Led display of the Humax.
Like say it displays L1.37 or H2.08 etc Are you getting it on your Humax?
Cause if you get the clock or a resetted clock straight away on Power-up that could mean corrupted loader in Flash memory.
If you DO get a loader displayed on Power-up then you still might think of checking your system ID as in my previous post..
Humaxman, First of all Happy new year mate,
You said power supply was replaced with a good working one taken from another Humax 5400 so Power Supply is out of question.
When you turn it on from the back panel Power Switch, you should have momentarily the Loader version displayed on the Led display of the Humax.
Like say it displays L1.37 or H2.08 etc Are you getting it on your Humax?
Cause if you get the clock or a resetted clock straight away on Power-up that could mean corrupted loader in Flash memory.
If you DO get a loader displayed on Power-up then you still might think of checking your system ID as in my previous post..
Last edited: