Oscam Emu TNT 19.2 test

[tolive]

hello,

tried it on gbquad with teamblue 6.4 mips32el, but get error when lauching oscam :

"/usr/lib/libcrypto.so.1.0.2 : version openssl_1.0.2d not found
required by /usr/bin/oscam"

i have installed all ipk, oscam and conf oscam.
what's wrong ?

thx

 

[juli13]

Have you tryed that

https://www.sat-universe.com/showpost.php?p=2037144865&postcount=2

It need only libcrypto 0.9.8 and start without problems in blackhole

 

[MAHDI-DZ]

opkg install libusb-1.0-0

 

[tolive]

hello

tried both of them nothing changed

 

[tolive]

now working, just changed the image to an openpli
many thanks all !

 

[Robertooo]

Which oscam TNT file is OK for Uno 4K SE?

 

[JanM262]

Which oscam TNT file is OK for Uno 4K SE?

I've installed Oscam r11678 and then I've manually replaced the binary in /usr/bin by the file from elumator

 

[regdal]

Biss does not work in my Solo2 after installation Oscam_tnt, put constant.cw file, provided atributes 755, nothing.
Who can help fix this problem? Thank you in advance.

 

[EnoSat]

Biss does not work in my Solo2 after installation Oscam_tnt, put constant.cw file, provided atributes 755, nothing.
Who can help fix this problem? Thank you in advance.

switch debug to level2 and check oscam debug

 

[zappaf]

put constant.cw file, provided atributes 755

Why? Not need it. Maybe you have wrong way.

 

[regdal]

to EnoSat
Every time your answers are so wise that no one understands them.
Maybe you can "decipher" your answer in detail? Thank you in advance.

 

[zappaf]

:clapping::clapping::clapping:

 

[EnoSat]

to EnoSat
Every time your answers are so wise that no one understands them.
Maybe you can "decipher" your answer in detail? Thank you in advance.

run detail logging

check status in livelog

which is so difficult ?

 

[regdal]

Which programm you using?

 

[dahaka]

Which programm you using?

oscam user interface from browser then -->config-->global-->logging

 

[EnoSat]

Which programm you using?

oscam

 

[Biko]

Wonderful effort
100% working

 

[campag5242]

Biss does not work in my Solo2 after installation Oscam_tnt, put constant.cw file, provided atributes 755, nothing.
Who can help fix this problem? Thank you in advance.

constant.cw for BISS, really? It is utter garbage for BISS: SoftCam.Key has been preferred for a few years now, and I seem to recall that the constant.cw module is not included in default builds of late.

Migrate to SoftCam.Key for your BISS needs. See https://github.com/oscam-emu/oscam-patched/wiki/BISS1-and-BISS2-mode-1-config

 

[vakula]

constant.cw for BISS, really? It is utter garbage for BISS: SoftCam.Key has been preferred for a few years now, and I seem to recall that the constant.cw module is not included in default builds of late.

Migrate to SoftCam.Key for your BISS needs. See https://github.com/oscam-emu/oscam-patched/wiki/BISS1-and-BISS2-mode-1-config

They are talking about BISS as provider and not as encryption

 

[campag5242]

I haven't a clue what you are on about vakula. BISS is BISS is BISS.

I co-wrote the revised biss code in oscam, providing a better means to associate each feed with the correct key. constant.cw was terrible for biss feeds. It worked for those normal CA channels with temporarily non-rotating CWs, but only because they were so few and far between that clashes were unlikely.

constant.cw has been dropped from default builds: not something I would have done without providing a replacement better suited to handle those temporarily stuck / non-rotating CAS, but that's where we are.