Hacking CA system challenge *Tandberg [ NO Keys Allowed in Chat Section/s ]*

H

harshy

Registered
Messages
746
JimBizkit said:
I guess this is caused by a bad signal. Or they are using a modulation that your dm800 cannot handle very well.

Tandberg is using standard CSA, there is no reason why your dm800 should not be able to handle it.
Click to expand...

Power3u works fine I had 9db for Wimbledon I noticed there's a lot going on in the logs plus the secs next to Oscam-emu was increasing all the time, I think it's as Kebien says au is enabled so how do I disable this?
 
C

chelo71

Super VIP
Messages
1,658
smedias said:
here is a guide thanks to abrakadabra26

just added one line to cccamd.list like "C: ip_address port user pass" but you have to set correct network mode in "mg_cfg":

best setting is "G: { 33 }" and thank to this setting you can run newcamd and cccam client.

vplug server can be run only under cccam so you have to add c line to cccamd.list in correct format.

1.run vplugserver with latest keys from Marwan26
2.click on vplugserver option - click on cccam server and chose version, add ip and port
3.then go to edit users and add user1/pass1 or any other

if you see login from unknown user in vplugserver log that means you have not set the G parameter yet

and link also from him on previous page is updated with all the keys

https://www.sendspace.com/file/ztbsrb
Click to expand...

how it is configured vplug server?
 
S

smedias

Registered
Messages
364
1.download from the link
2.run it
3.click on "vplug server options" Menu
4.click the tick and make active CCcam Server active
5.select cccam version - for example 2.3.0
6.put ip of your computer
7. leave port 12000
8.click save at the bottom of the page

how to add user(your e2 receiver)
1. click edit users menu
2. if not present any user click on add users menu
- select name user1/2/3
click ok
3. put pass1 for pass
4. click save

for receiver:
just enter in cccamd.list
C: (ip of your PC) 12000(for port) user1 pass1
find row and set G: {33}

then run from pc vplugserver, leave log active to see whats going on for any mistake
then restart receiver or just emu

and last as far as i remember edit cards menu in the package is already set so you dont have to change anything there
 
Last edited:
C

chelo71

Super VIP
Messages
1,658
smedias said:
1.download from the link
2.run it
3.click on "vplug server options" Menu
4.click the tick and make active CCcam Server active
5.select cccam version - for example 2.3.0
6.put ip of your computer
7. leave port 12000
8.click save at the bottom of the page
Click to expand...
not work?
 
M

mrchisholm

Registered
Messages
4
thanks to everyone making this possible!

now i'm watching wimbledon feed on 7E in dvbdream with vplug 2.4.6 and the tandberg.mdl but every few min when it change key u get a breakup in picture for 1-3 seconds, any idea what could be causing this? i did a fresh install of every app and it's still breaks up. (no it's not a signal failure, it happens when the key roll)
 
Last edited:
C

chelo71

Super VIP
Messages
1,658
smedias said:
1.download from the link
2.run it
3.click on "vplug server options" Menu
4.click the tick and make active CCcam Server active
5.select cccam version - for example 2.3.0
6.put ip of your computer
7. leave port 12000
8.click save at the bottom of the page

how to add user(your e2 receiver)
1. click edit users menu
2. if not present any user click on add users menu
- select name user1/2/3
click ok
3. put pass1 for pass
4. click save

for receiver:
just enter in cccamd.list
C: (ip of your PC) 12000(for port) user1 pass1
find row and set G: {33}

then run from pc vplugserver, leave log active to see whats going on for any mistake
then restart receiver or just emu

and last as far as i remember edit cards menu in the package is already set so you dont have to change anything there
Click to expand...

where cccamd.list?
 
You must log in or register to reply here.
Top