Enigma2 SifTeam Flash Version 0.1.0 (9000-900-910)

[tom_63]

Ok. once again for those with "loading module" and nothing else...

from John1
1- open putty to put the u-boot
2- select serial and change 9600 to 115200 and select open empty box will appear
3- now switch on box and press CTRL+z same time you will see the word cubrevo
4- paste this line and put ipbox ip and router gateway

setenv bootargs "console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 rootfstype=jffs2 rw bigphysarea=10240 ip=10.0.0.52:10.0.0.138:255.255 .255.0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";save; boot
5- press enter and it will copy the u-boot.

now something very important:

6- saveenv

Without this your environment isn´t saved and the image will not boot.

Greetz TOM

 

[oreman]

when i flash the image with usb stick and reboot the box displays 'loading module' and does not proceed. please help

 

[xxxAxxx]

before you flash the E2 .....what img was on ipbox ????

 

[prdehoop]

Please read post off Tom above, you need to setenv line and after that do an saveenv, after that reboot you're box and it will boot futher then loading modul

 

[dreamnu]

can´t get E2 to work on flash memory

hi!
i can´t get E2 to work:mecry:, i have tray it on usb stick,
hdd and now on flash.
i get the same results on logg both on hdd as in flash memory.
i have install u-boot 1.3.3 to.
this is frome flash memory test putty log.:thum:

--------------------------------------------

Logg:
U-Boot 1.3.1 (Oct 24 2008 - 18:09:07) - stm23-2008-03-19
Board: cuberevo (0x2D42C041)
Board: 12 dotmatrix vfd front
DRAM: 128 MB
Flash: 32 MB
In: serial
Out: serial
Err: serial
Reserve 0x2010000 bytes from 0xa5ff0000 for DGS upgrade buffer.
Setup mac address.
booting...
## Booting image at a0060000 ...
Image Name: Linux 2.6
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 1846381 Bytes = 1.8 MB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Warning: Unable to determine if kernel is built for 29- or 32-bit mode!

Starting kernel console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 rootfstype=jffs2 rw bigphysarea=10240 ip=192.x.x.x:192.x.x.x:192.x.x.x:255.255.255.0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 - 0x00000000 - 0 ...


INIT: version 2.86 booting

[fp] ver. 08.03.27
[fp] init 12 dotmatrix vfd
Mount /dev in tmpfs
Copying device nodes to /dev
Starting portmap daemon.../etc/init.d/portmap: line 79: pidof: not found
.
LOADING MODULES
init AVS
init stmfb
load a/v firmware
init embx
init player
Segmentation fault
insmod: cannot insert '/lib/modules/player2.ko': unknown symbol in module
insmod: cannot insert '/lib/modules/sth264pp.ko': unknown symbol in module
insmod: cannot insert '/lib/modules/stmalloc.ko': unknown symbol in module
Opening frame buffer device `/dev/fb0 '
MODE: 576i50
DEBUG1:
74074 68 12 38 5 64 6
0 513
DEBUG2:
74074 69 12 41 5 63 3
0 1
config.outputid=1
showSinglePic /boot/bootlogo.mvi
LOADING e2
Mounting local filesystems...
mount: mounting /dev/sda1 on /hdd failed: Invalid argument
Cleaning /tmp.
mount: mounting /dev/sr0 on /media/dvd failed: No such device or address
mount: mounting /dev/sda1 on /hdd/movie failed: Invalid argument
Hostname: CubeRevo.
starting telnetd
Starting FTP server: vsftpd.
Sat Dec 12 20:00:00 CET 1970
starting e2->
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (8) graphics acceleration manager
+ (9) gLCDDC
couldn't open LCD - load lcd.o!
+ (9) GFBDC
10240k video mem
FBIO_SET_MANUAL_BLIT: Inappropriate ioctl for device
gFBDC::setResolution(xres=720, yres=576)
fbClass::SetMode(nxRes=720, nyRes=576, nbpp=32)
VIDEO STOP
VIDEO_STOP failed
MODE: 576i50
DEBUG1:
74074 68 12 38 5 64 6
0 513
DEBUG2:
74074 69 12 41 5 63 3
0 1
config.outputid=1
VIDEO START
VIDEO_PLAY failed
bounds x=0, y=0, w=720, h=576
defrect x=0, y=0, w=720, h=576
x=54, y=59
1. 0, 0, 720, 576

VIDIOC_S_INPUT: ioctl error -1 : No such device

VIDIOC_S_CROP: ioctl error -1 : No such device

8620kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 2880)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) Socket MMI
[eSocketMMIHandler] created successfully
+ (20) misc options
+ (20) UHF Modulator
couldnt open /dev/rfmod0!!!!
+ (20) AVSwitch Driver
couldnt open /dev/avs !
+ (20) RC Input layer
+ (21) Console RC Driver
failed to open /dev/vc/0
+ (21) input device driver
Input device "Relook IR Keyboard" is a keyboard.
failed to open /dev/input/event1
Input device "" is not a keyboard.
failed to open /dev/input/event2
Input device "" is not a keyboard.
failed to open /dev/input/event3
Input device "" is not a keyboard.
Found 4 input devices!
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
cannot open /proc/stb/tsmux/input0
cannot open /proc/stb/tsmux/input1
done, found 0 common interface slots
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
+ (41) eServiceFactoryMP3
eServiceFactoryMP3->

eStaticServiceMP3Info->

reached rl 70
---- opening lame channel db
reading services
main thread is non-idle! display spinner!
no spinner DC!
loaded 9090 services
scanning for frontends..
opening frontend 0
failed! (/dev/dvb/adapter0/frontend0) No such device
found 1 adapter, 0 frontends and 1 demux
RTC not ready... wait for transponder time
[EPGC] Initialized EPGCache
eWidgetDesktop::setPalette(gPixmap &pm)->
4
5
eWidgetDesktop::setPalette(gPixmap &pm)-<
Loading spinners...
found 4 spinner!

setIoPrio(int prio_class, int prio)->
ioprio_set(1, 0, 16387) 288
setIoPrio best-effort level 3 ok
setIoPrio(int prio_class, int prio)-<
python.execute(mytest, __main__);
main thread is non-idle! display spinner!

--------------------------------------------

can some help me please, What is mine problem?
i get same results on hdd, when i test it on hdd
i flash first E2_on_HDD.zip on it.:thum:

dreamnu

 

[davkari]

ipbox enigema2

Bomdia someone can help me by fafor, I ENIGIMA2 out in my IPBox9000; already tried to put the Imagu E2 IN STIK USB is the estalacao yudimarce without prolbemas. then reboot when the box is not booting leaves on it. What could you give me a hand by esplica Grimsby Grimsby thanks davanco .............

 

[slick]

the links only gets me back to the sat uni main page?

how many post do u have to have to download this file?

 

[polly33]

Enigma2 SifTeam Flash Version 0.1.0

Enigma2 works very well ipbox910 hd / tested 100% ok, just need to follow steps of installation / after several attempts I managed to put in motion E2 on ipbox910 / all success.

 

[rye787]

Polly... can you tell us step by step how you did it, as there are different images, different methods.

 

[tango110]

Sorry all fixed bij setting the setenv in Document en DO AN SAVEENV after !!

okay i dont understand this message plz tell what to do

 

[tango110]

Got it up and running, but can only under satellite setup chose between 13 east and 19,2 east weird , and it only see 1 tuner and not 2 ? under sat setup any clue's why ?

 

[animal666]

Try FTPing in and putting a new satellite.xml file in there. you can find them in the dreambox section.
gonna have another go with it this wkend, see if i can get more sat's in and cable set up as well.

 

[renexx]

THX hopes this img kan birng my 910hd back to life

 

[maxsuma]

idownload this image with flash tool everthing fine but when i download pkt plugin icant start incubuscamd

now ilike to download from usb stick how is this work

press and hold power swicth box on usb uprade then ok but it dozent do anything is there any other way to get image work from usb stick

 

[maxsuma]

has anyone manage to download incubuscamd icoulndt keep giving me error on pkd3 download menu
idelete lots rubbish from the so i got some space but still not downloading incubus only newcs work

 

[maxsuma]

guys how am i going to put image with usb stick it dozent do anything power of then press power usb update then what do i have to do

 

[k2k2000]

this is old Enigma2 SifTeam Flash Version 0.1.0 thread.
new version is 0.2.0 .

for better stability and functionality
try Enigma2 SifTeam 0.2.0 mod PKT beta 3.0b

http://www.sat-universe.com/showthread.php?t=106488