big network problem with Dm 800 hd clone

[goni el]

hi i have network problem in Dm 800 hd it workt good for a month
and it stop working,
I did a network test, these where my results, I have also lost my channels

LAN Adapter
Intergrated Ethernet/ and theres a tick in the box

Local Network
connected/ and theres a tick in the box

DCHP
enable/ and theres a tick in the box

IP Address
unconfirmed/ and theres a X in the box

Namesever
unconfirmed/ and theres a X in the box
can you help me please
thank you from Goni el

 

[Ferret]

Hi mate

It looks as though you have lost connection to you router.

First of all make sure all the cables are secure and then power down your router an 800 and then re apply power.

If this does not work.

On your remote

Menu-setup-system-network adapter

I there tick DHCP and reboot.

See if that help and let us know.

Ferret

 

[fikos67]

same problems with me when i change the boxes ip , but always after a reboot its fine .......

 

[ozzie86]

router

check your lease time in the router

or use Static IP on your dream or Static DHCP in your router

 

[goni el]

i put DHCP of and i make a new ip, netmask, dns after that i restarted but still the same the iven when i hold the buton dot show me the ip
i can flash the image withaut problem with dreamup my dm 800 hd is ss75 sim 2.01 end now i flash it nabilo blackhole ss72 i trait
with wlan is the same no ip can you help me please

 

[Ferret]

Enable DHCP again a reboot. Make sure you can now see the 800.

In adaptor settings turn off DHCP only and alter just last 3 digits

Like 192.168.0.***

Ferret

 

[stauffie]

network from dream 800 serie sucks big time its nown by DMM but they do not want to fix the problem

 

[goni el]

Device Information

Firmware Version
:
W300V2.0.1a_DR0_OV

MAC Address
:
00:25:12:b3:8a:7f
LAN

IP Address
:
192.168.1.1

Subnet Mask
:
255.255.255.0

DHCP Server
:
Enabled
WAN

Virtual Circuit
:


Status
:
Connected

Connection Type
:
PPPoE

IP Address
:
10.103.95.95

Subnet Mask
:
255.255.255.255

Default Gateway
:
10.103.0.1

DNS Server
:
217.24.241.206

NAT
:
Enabled

PPP connection time
:
0d:16h:37m:32s
ADSL

ADSL Firmware Version
:
FwVer:3.10.17.0_TC3085 HwVer:T14.F7_5.0

Line State
:
Showtime

Modulation
:
ADSL2 PLUS

Annex Mode
:
ANNEX_A

Downstream Upstream
SNR Margin
:
33.3 37.2 db
Line Attenuation
:
26.2 16.7 db
Data Rate
:
512 126 kbps
this shows my router is,t ok

 

[Ferret]

Are you connect via a router?

Because the IP and Gateway here look like nonsense to me

IP Address
:
10.103.95.95

Subnet Mask
:
255.255.255.255

Ferret

Default Gateway
:
10.103.0.1

 

[goni el]

can i tray with usb wlan which image work ok?

 

[goni el]

Device Information

Firmware Version
:
W300V2.0.1a_DR0_OV

MAC Address
:
00:25:12:b3:8a:7f
LAN

IP Address
:
192.168.1.1

Subnet Mask
:
255.255.255.0

DHCP Server
:
Enabled
WAN

Virtual Circuit
:


Status
:
Connected

Connection Type
:
PPPoE

IP Address
:
10.103.95.95

Subnet Mask
:
255.255.255.255

Default Gateway
:
10.103.0.1

DNS Server
:
217.24.241.206

NAT
:
Enabled

PPP connection time
:
0d:21h:18m:36s
ADSL

ADSL Firmware Version
:
FwVer:3.10.17.0_TC3085 HwVer:T14.F7_5.0

Line State
:
Showtime

Modulation
:
ADSL2 PLUS

Annex Mode
:
ANNEX_A

Downstream Upstream
SNR Margin
:
32.8 37.6 db
Line Attenuation
:
26.2 16.7 db
Data Rate
:
512 126 kbps

yes is connected with router and is still the same
can i tray with usb wlan which image work ok?

 

[Ferret]

See this thread mate for wireless Lan info.


http://www.sat-universe.com/showthread.php?t=153020

Ferret