UltimateFlashRecovery 910

UltimateFlashRecovery 910 rev 0997 

as I said I wanted to make some cosmetic corrections nen, and still am in the process stumbled over the question of MacAddress ... I all in this version (yet) see it as pure contingency image is simply the box with a standard MacAddress ethaddr = 00:50: fd: ff: 12:34 equipped (but I think about it, depending on whether one state of bootargs can save the MAC and IP addresses and paste them after flashing again, so the program automatically without further action by the user) 
For the moment belongs to the box corresponding to the MAC must be set correctly or manually, again ... wenns it must be. 

[B]What makes the package? [/B]

1. It is flashed completely clean the entire 2.0beta/final from Kathrein 
2. It is an absolutely-clean btcf flashed (who does not btcf should know: this is the bootconfigsektor) 
3. The bootconf the correct bootargs for 2.0 beta, and has the ethaddr 00:50: fd: ff: 12:34 

[B]Prerequisites for application:[/B] 

UFS910 (ja nee ... is klar ne?) 
PC with HyperTerminal or similar program (kermit binary must be supported) 
With Windows Vista, Windows7, and there are probably hinundwieder problems with the application of Hpyerterminal. As a fallback option is referred to TeraTermPro what is supposed to work better. 
Null modem cable between the PC and UFS910 
USB Flash Drive, fat32 formatted, with folder structure / kathrein/ufs910 

[B]Procedure: [/B]

1. Download and unzip ufr910.zip 
2. ufr910.img the file on the USB stick to copy the folder / kathrein/ufs910 
3. the file irgenwo ufr910.exe sit on the PC where they were later rediscovers 
3. Start HyperTerminal, n COMx connection with "115200, 8,, 1, does not produce" (these settings and operation of HT are masses of documents, so here I am no closer to it) ENTERED 
4. USB stick to the box like plug in, switch on with power button and press in the HyperTerminal booting IMMEDIATELY by the <enter> cancel button. In HyperTerminal is the box with the prompt STB7100ref> available. 
5. Following command followed by the enter key <enter> in Hyperterminal: 
loadb a4000000, a4000000 Bootmen 
(if you typo here: you can do with nothing broken evt incorrect figures) 
6. in the HyperTerminal displays the message "ready for download binary ...." 
7. In the HyperTerminal in the menu on 
- "Transfer" button 
- Select "send file" 
- The pop-up window, select the file ufr910.exe (where it was the same ...???) 
- And very importantly, choose the protocol "Kermit" and then clicking the button <senden> 
8. min wait for about 3 1 / 2 and do nothing until picture again (with "Initial Installation") is 

[B]Notes: [/B]

This package ALWAYS works if at least uboot and the serial port of the box are still intact. MacAddress, IPAddress, battered or even completely deleted bootargs, Fire Walls and virus scanner and all the other little problems are irrelevant and have no effect on the function. The only unknowns: the USB stick. How not to work with all other applications in connection with the stick UFS910 MUST each stick. For this case, appears in the HT after the transfer of a message ufr910.exe <interrupt> UFS910 to start immediately and the new. 
Future enhancements to the rev 1.0: CRC32 verification with verification result of the flash. Recovery MAC-/IPadressen if still present, further emergency Images (1.06, 1.04 ...), 
Other Flash packages: e2 images, images with minimum or 2nd uboot bootloader (which can then also just flashed directly without going through 3 other images), flash full backups (ie, complete incl bootargs images and mini) 
This HowTo do I lay in the final version, of course, still in the package. 
Addendum: Some people have the Originaluboot the 910 replaced by a modified uboot 1.3.1. Since this version of the command loadb unfortunately not known, the user can not use this package. 

And if the men should read this from Kathrein: This method is far safer and much faster than those published on the portal Kathrein TippelMethode with erase blah and tftp-server

[B]What is UltimateFlashRecovery? [/B]

1. flaszuje perfectly clean 2.0beta/final Kathrein 
2. creates a perfectly clean btcf (btcf otherwise bootconfigsektor) 
3. to assign proper bootconfig bootargs for 2.0beta, and sets the Mac 
ethaddr 0:50: fd: ff: 12:34 

[B]What does it possess?[/B] 

- UFS910 (probably obvious?) 
- PC with XP Hyperterminal or similar (binary kermit) 
- The conductivity crossover between the PC and 232 UFS910 
- Drive, fat32, Xba volume of directory / kathrein/ufs910 

[B]Procedure: [/B]

1. download and unzip ufr910.zip 
2. ufr910.img file on the flash drive to copy the directory / kathrein/ufs910 
3. ufr910.exe save the file somewhere on your PC (eg on the desktop) 
4. run hyperterminal, connection by COMx myth "115200, 8, n, 1, NO" 
5. Insert the USB pen Helmets, Helmet turn at the same time repeatedly 
pressing the Enter key. 
The terminal window will stop the cascade STB7100ref Prompt>. 
7. pat as stated below and hit <enter>: 
loadb a4000000, a4000000 bootm 
We will show the answer "ready for download binary ...." 
8. in the terminal you have options to send files 
- Press "Send" 
- Select "File" 
- Look for the file in the window ufr910.exe (unless you're on the desktop ...???) 
- And very important, select Protocol, "Kermit" and finally click on <Send> 
9. The whole process lasts up to 5 min, the preview pane, you will have 
10. READY 


[B]Notes: [/B]

This package always work, you just need a good and uboot 
RS connection. 
MAC addresses, IP addresses, smashed Bootargs, virus scanners, firewalls and other 
przeszkadzajki have no impact on the reliability of 
In Windows Vista, it could come to a bias in ufr910.exe. 
You will know it's report "bad magic ..." in a terminal window 
Great unknown: pendrive. 
If the pen will not be recognized will receive a report 
<interrupt> UFS910 then resets 
If the pen will be recognized but will not be able to read this data 
receive a report 
ERROR: sohci_submit_job: ENOMEM 
ERROR: failed sohci_submit_job 
In this case K, the PEN.