- Messages
- 10,198
UltimateFlashRecovery 910th .. in 5 min to image
ui wow ... so many thank-s before any program there is
ok ... so this is also justified here comes now:
UltimateFlashRecovery 910 rev 0997
as I said I wanted to make some cosmetic corrections nen, and still am in the process stumbled over the question of MacAddress ... I all in this version (yet) see it as pure contingency image is simply the box with a standard MacAddress ethaddr = 00:50: fd: ff: 12:34 equipped (but I think about it, depending on whether one state of bootargs can save the MAC and IP addresses and paste them after flashing again, so the program automatically without further action by the user)
For the moment belongs to the box corresponding to the MAC must be set correctly or manually, again ... wenns it must be.
What makes the package?
1. It is flashed completely clean the entire 2.0beta/final from Kathrein
2. It is an absolutely-clean btcf flashed (who does not btcf should know: this is the bootconfigsektor)
3. The bootconf the correct bootargs for 2.0 beta, and has the ethaddr 00:50: fd: ff: 12:34
Prerequisites for application:
UFS910 (ja nee ... is klar ne?)
PC with HyperTerminal or similar program (kermit binary must be supported)
Null modem cable between the PC and UFS910
USB Flash Drive, fat32 formatted, with folder structure / kathrein/ufs910
Procedure:
1. Download and unzip ufr910.zip
2. ufr910.img the file on the USB stick to copy the folder / kathrein/ufs910
3. the file irgenwo ufr910.exe sit on the PC where they were later rediscovers
3. Start HyperTerminal, n COMx connection with "115200, 8,, 1, does not produce" (these settings and operation of HT are masses of documents, so here I am no closer to it) ENTERED
4. USB stick to the box like plug in, switch on with power button and press in the HyperTerminal booting IMMEDIATELY by the <enter> cancel button. In HyperTerminal is the box with the prompt STB7100ref> available.
5. Following command followed by the enter key <enter> in Hyperterminal:
loadb a4000000, a4000000 Bootmen
(if you typo here: you can do with nothing broken evt incorrect figures)
6. in the HyperTerminal displays the message "ready for download binary ...."
7. In the HyperTerminal in the menu on
- "Transfer" button
- Select "send file"
- In the popup window, select the file ufr910.exe (where it was the same ...???)
- And very importantly, choose the protocol "Kermit" and then clicking the button <senden>
8. min wait for about 3 1 / 2 and do nothing until picture again (with "Initial Installation") is
Notes:
This package ALWAYS works if at least uboot and the serial port of the box are still intact. MacAddress, IPAddress, battered or even completely deleted bootargs, Fire Walls and virus scanner and all the other little problems are irrelevant and have no effect on the function. The only unknowns: the USB stick. How not to work with all other applications in connection with the stick UFS910 MUST each stick. For this case, appears in the HT after the transfer of a message ufr910.exe <interrupt> UFS910 to start immediately and the new.
Future enhancements to the rev 1.0: CRC32 verification with verification result of the flash. Recovery MAC-/IPadressen if still present, further emergency Images (1.06, 1.04 ...),
Other Flash packages: e2 images, images with minimum or 2nd uboot bootloader (which can then also just flashed directly without going through 3 other images), flash full backups (ie, complete incl bootargs images and mini)
This HowTo do I lay in the final version, of course, still in the package
And if the men should read this from Kathrein: This method is far safer and much faster than those published on the portal Kathrein TippelMethode with erase blah and tftp-server
ui wow ... so many thank-s before any program there is
ok ... so this is also justified here comes now:
UltimateFlashRecovery 910 rev 0997
as I said I wanted to make some cosmetic corrections nen, and still am in the process stumbled over the question of MacAddress ... I all in this version (yet) see it as pure contingency image is simply the box with a standard MacAddress ethaddr = 00:50: fd: ff: 12:34 equipped (but I think about it, depending on whether one state of bootargs can save the MAC and IP addresses and paste them after flashing again, so the program automatically without further action by the user)
For the moment belongs to the box corresponding to the MAC must be set correctly or manually, again ... wenns it must be.
What makes the package?
1. It is flashed completely clean the entire 2.0beta/final from Kathrein
2. It is an absolutely-clean btcf flashed (who does not btcf should know: this is the bootconfigsektor)
3. The bootconf the correct bootargs for 2.0 beta, and has the ethaddr 00:50: fd: ff: 12:34
Prerequisites for application:
UFS910 (ja nee ... is klar ne?)
PC with HyperTerminal or similar program (kermit binary must be supported)
Null modem cable between the PC and UFS910
USB Flash Drive, fat32 formatted, with folder structure / kathrein/ufs910
Procedure:
1. Download and unzip ufr910.zip
2. ufr910.img the file on the USB stick to copy the folder / kathrein/ufs910
3. the file irgenwo ufr910.exe sit on the PC where they were later rediscovers
3. Start HyperTerminal, n COMx connection with "115200, 8,, 1, does not produce" (these settings and operation of HT are masses of documents, so here I am no closer to it) ENTERED
4. USB stick to the box like plug in, switch on with power button and press in the HyperTerminal booting IMMEDIATELY by the <enter> cancel button. In HyperTerminal is the box with the prompt STB7100ref> available.
5. Following command followed by the enter key <enter> in Hyperterminal:
loadb a4000000, a4000000 Bootmen
(if you typo here: you can do with nothing broken evt incorrect figures)
6. in the HyperTerminal displays the message "ready for download binary ...."
7. In the HyperTerminal in the menu on
- "Transfer" button
- Select "send file"
- In the popup window, select the file ufr910.exe (where it was the same ...???)
- And very importantly, choose the protocol "Kermit" and then clicking the button <senden>
8. min wait for about 3 1 / 2 and do nothing until picture again (with "Initial Installation") is
Notes:
This package ALWAYS works if at least uboot and the serial port of the box are still intact. MacAddress, IPAddress, battered or even completely deleted bootargs, Fire Walls and virus scanner and all the other little problems are irrelevant and have no effect on the function. The only unknowns: the USB stick. How not to work with all other applications in connection with the stick UFS910 MUST each stick. For this case, appears in the HT after the transfer of a message ufr910.exe <interrupt> UFS910 to start immediately and the new.
Future enhancements to the rev 1.0: CRC32 verification with verification result of the flash. Recovery MAC-/IPadressen if still present, further emergency Images (1.06, 1.04 ...),
Other Flash packages: e2 images, images with minimum or 2nd uboot bootloader (which can then also just flashed directly without going through 3 other images), flash full backups (ie, complete incl bootargs images and mini)
This HowTo do I lay in the final version, of course, still in the package
And if the men should read this from Kathrein: This method is far safer and much faster than those published on the portal Kathrein TippelMethode with erase blah and tftp-server