Problem with DM800SE "tuner failed"

[franhv]

Hi, I have a problem with my DM800SE (clone). It appears the message "Tune Failed". I thinked that the problem was on the tuner, but I tried to change the tuner with other, and the problem persists.

Anyone have any solution?

 

[manufact]

no signal...

 

[franhv]

no signal...

But I have another box and works very well with the same installation. In this box I have signal. I think that it's not problem of tuner, but I don't know where is the problem...

 

[bertazwin]

last time I have the same situation. tuner was inside, but no signal. I have to change the tuner... same problem. after I use a stronger power supply and all was perfekt -also with old tuner-

 

[Chapa30]

The clones have this problem.

If you look at the tuner it does not sit correctly on its slot. Take it off and re sit it.

Chapa

 

[franhv]

last time I have the same situation. tuner was inside, but no signal. I have to change the tuner... same problem. after I use a stronger power supply and all was perfekt -also with old tuner-

A power supply with more than 12V?

The clones have this problem.

If you look at the tuner it does not sit correctly on its slot. Take it off and re sit it.

Chapa

Thank you but I tried to do this and the problem persists...

 

[Chapa30]

You havent done it correctly.

After a few trys you will have working

 

[franhv]

You havent done it correctly.

After a few trys you will have working

Did you do this with the box in ON or OFF?

 

[Chapa30]

Off m8,

Just look at the box tuner when you open the top and you see that the tuner is sideways.

one way to avoid this is to take off the piece of metal which is screwed on the outside. This piece is what is causing the tuner not to sit correctly.
Have a try

 

[dickdark]

I've had this.If you have confirmed it's not the tuner it will be a burnt out inductor (L1300 12v 0.56uh 0805 +/- 10%)
TDK MLF2012DR56K.
On my 800se it boots up to image perfect and i am able to enter all menus etc but comes up tuner nothing/empty.I am yet to have this new part fitted but it certainly won't work without it being replaced.
See top right below(above and left of L1301)

 

[franhv]

Off m8,

Just look at the box tuner when you open the top and you see that the tuner is sideways.

one way to avoid this is to take off the piece of metal which is screwed on the outside. This piece is what is causing the tuner not to sit correctly.
Have a try

I tried to do this but I have not solved the problem...

 

[franhv]

I've had this.If you have confirmed it's not the tuner it will be a burnt out inductor (L1300 12v 0.56uh 0805 +/- 10%)
TDK MLF2012DR56K.
On my 800se it boots up to image perfect and i am able to enter all menus etc but comes up tuner nothing/empty.I am yet to have this new part fitted but it certainly won't work without it being replaced.
See top right below(above and left of L1301)

Tomorrow I will confirm if I have the same problem as you. Thanks.

 

[franhv]

I think all is OK... But the problem of "Tune Failed" persists...

 

[franhv]

Anyone has an idea?

 

[oldtam]

Anyone has an idea?

Happened to me a few years ago. I was advised to buy a new power pack. And to my suprise it solved the tuner problem.

 

[franhv]

Happened to me a few years ago. I was advised to buy a new power pack. And to my suprise it solved the tuner problem.

But I tried to connect with others power pack and not solve my problem...

 

[peja72]

if you use open pli you gonne heave this problem 800se dont like pli strange change image

 

[sakisvele]

I too have the same problem.
While playing with the motor with disec does not play.
rather the problem is the motherboard does not pass the analog power so that no downloading channels.

 

[franhv]

if you use open pli you gonne heave this problem 800se dont like pli strange change image

Sorry, but I use Tsimage...

 

[dickdark]

yeah that look's ok my L1300 is just a sooty shadow.don't know what too suggest now.