PowerVu Chat [only chat, don‘t post keys here]

R

Robinson74

Registered
Messages
558
With the default emu reader, I get the following log:

Code: 
2019/01/01 23:06:43 4C145B6F r      (emu) Key not found: P 006B 00
2019/01/01 23:06:43 4C145B6F r      (emu) ECM failed: Key not found
2019/01/01 23:06:43 6F097D42 c      (ecm) dvbapiau (0E00@000000/0000/006B/99:B0916380374214093453170487145696): not found (1 ms) by emulator
2019/01/01 23:06:43 6F097D42 c   (dvbapi) Demuxer 0 restarting decodingrequests after 0 ms with 1 enabled and 1 disabled ecmpids!
2019/01/01 23:06:43 6F097D42 c   (dvbapi) Demuxer 0 trying to descramble PID 1 CAID 0E00 PROVID 000000 ECMPID 17A4 ANY CHID PMTPID 13F3 VPID 0681
2019/01/01 23:06:53 4C145B6F r      (emu) Key not found: P 006B 00
2019/01/01 23:06:53 4C145B6F r      (emu) ECM failed: Key not found
2019/01/01 23:06:53 6F097D42 c      (ecm) dvbapiau (0E00@000000/0000/006B/99:C60878AD1447E84AC8412C98FEB9C443): not found (1 ms) by emulator
2019/01/01 23:06:53 6F097D42 c   (dvbapi) Demuxer 0 restarting decodingrequests after 1 ms with 1 enabled and 1 disabled ecmpids!
2019/01/01 23:06:53 6F097D42 c   (dvbapi) Demuxer 0 trying to descramble PID 1 CAID 0E00 PROVID 000000 ECMPID 17A4 ANY CHID PMTPID 13F3 VPID 0681
2019/01/01 23:07:03 4C145B6F r      (emu) Key not found: P 006B 00
2019/01/01 23:07:03 4C145B6F r      (emu) ECM failed: Key not found
2019/01/01 23:07:03 6F097D42 c      (ecm) dvbapiau (0E00@000000/0000/006B/99:DA7B1A63ED659FCFC36B890EDF44153A): not found (0 ms) by emulator
2019/01/01 23:07:03 6F097D42 c   (dvbapi) Demuxer 0 restarting decodingrequests after 1 ms with 1 enabled and 1 disabled ecmpids!
2019/01/01 23:07:03 6F097D42 c   (dvbapi) Demuxer 0 trying to descramble PID 1 CAID 0E00 PROVID 000000 ECMPID 17A4 ANY CHID PMTPID 13F3 VPID 0681

What should my next step be?
Wrong SoftCam.Key or oscam.conf or some other file?
 
R

Rickk

Registered
Messages
2,375
wait - 5 minutes

2019/01/01 23:32:38 1123DFC7 c (dvbapi) Demuxer 0 restarting decodingrequests after 1 ms with 1 enabled and 1 disabled ecmpids!
2019/01/01 23:32:38 1123DFC7 c (dvbapi) Demuxer 0 trying to descramble PID 1 CAID 0E00 PROVID 000000 ECMPID 17A1 ANY CHID PMTPID 13F0 VPID 048D
2019/01/01 23:32:42 796995B8 r (emu) Key not found: P 0068 00
2019/01/01 23:32:42 796995B8 r (emu) ECM failed: Key not found
2019/01/01 23:32:42 796995B8 r (emu) Key not found: P 0068 00
2019/01/01 23:32:42 796995B8 r (emu) ECM failed: Key not found
2019/01/01 23:32:44 796995B8 r (emu) Writing key file: /etc/tuxbox/config/SoftCam.Key
2019/01/01 23:32:44 796995B8 r (emu) Key written: P 90066 00 E49E88BF42D712
Click to expand...
 
R

Robinson74

Registered
Messages
558
Thanks.
Some patience and keys have been added.
By the way, is this because I had correct EMM keys in my SoftCam.Key or are there any AFN EMM keys built in oscam-emu itself?
 
K

kebien

Registered
Messages
1,329
ro_54 said:
NO, 3803V is not there.
Click to expand...

Sometimes to need to be creative.
EMM keys are sometimes good for more than one trasponder or service.
You should try EMM keys you have for similar services in the same sat or adjacent since could be valid.
Best bet is to see who the provider is and look for other trasponders with same provider in same sat or different.
 
J

jdavid22

Registered
Messages
168
Some time ago I placed many emmkey for a specific tp of the 105w and after a while one of the many found the ecm from there I took out an emm key that was valid for the 135w, as in some occasion commented anubis_ir
 
ro_54

ro_54

Registered
Messages
685
I used all emm keys for encompass provider, but no luck.
there is something different on this tp.
 
A

antrabe

Registered
Messages
530
one doubt that i have if already know the key which should be the format to put in softcam file to works with oscam in dreambox900

thanks
 
T

tuvalo

Registered
Messages
230
In use is oscam11448emu with stream relay option. I recorded a PowerVu Channel on my E2 Receiver on the USB drive. The receiver is not aible to show picture so i want to watch the recording on my pc. VLC is ot show a picture. Do I have to encode it twice? I think the emu did it on the receiver.
 
D

djmx

Registered
Messages
27
Hello Folks,


Auto update for AFN channels does not work anymore with latest oscam releases 11456, 11451 …
Latest version working for me is 11444

Any clues please ?

Thanks
 
fiji

fiji

Member
Messages
1,095
cockta said:
In use is oscam11448emu with stream relay option. I recorded a PowerVu Channel on my E2 Receiver on the USB drive. The receiver is not aible to show picture so i want to watch the recording on my pc. VLC is ot show a picture. Do I have to encode it twice? I think the emu did it on the receiver.
Click to expand...

Powrvu video channel befor decoding no possibale to watch it on
any emu or media player devices

after decoding can be playable on any media player in any device
decoding can be only in spacial hd boxes with record ts file.
 
predator_2

predator_2

Donating Member
Messages
175
AFN Update

djmx said:
Unix starttime: 1547198706
Starttime: 11.01.2019 11:25:06
Version: oscam-1.20_svn-r11451
Compiler: mipsel-unknown-linux-gnu
Box type: dm8000 (generic)

2019/01/11 11:26:34 5199BFCE r(emu) Writing key file:/var/keys/SoftCam.Key
2019/01/11 11:26:34 5199BFCE r(emu) Key written: P 9006C 00
2019/01/11 11:26:34 5199BFCE r(emu) Key written: P 9006C 01

Oscam EMU 11451 is working.
Click to expand...
 
Last edited:
3satbox

3satbox

Registered
Messages
252
Are you kidding or... On Christmas eve they changed to "26" and you insist on 10!?

sent using taptalk
 
You must log in or register to reply here.
Top