Method of Opening PowerVu Channels in Enigma2 Using Oscam
- Thread starter Ghouri
- Start date
stinkefisch
Registered
- Messages
- 183
Get my pluging
http://www.sat-universe.com/showthread.php?t=294230
update the Key, restart OScam and configure stream relay
IMPORTANT:
The stream relay needs a fast CPU. Not every STB is fast enough.
If you cannot fix stuttering with the following guide, likely your CPU is
too slow.
For best performance, the "Include ECM in http streams" setting must be enabled.
If your image supports it (openpli, openatv), you can find it here:
OpenWebif -> Settings -> Customize
If the setting is not available, you may need to adjust the "ECM fix delay"
setting in oscam webif (Config -> Stream Relay).
Increase/Lower it until there is no stuttering.
When using VU+ devices, make sure to use the latest drivers (June 2015), if
you encounter any problems.
Channel Config:
1. Go to the OpenWebif and click on the "Stream" button for the channel you want to add.
2. Download and save the .m3u file.
3. Open the .m3u file with a text edior and get the stream link. It looks like this:
http://stb:8001/1:0:19:0123:3EF:1:C00000:0:0:0:
4. Replace the port (8001) with the relay port (default: 17999) and the host name ("stb") with 127.0.0.1
http://127.0.0.1:17999/1:0:19:0123:3EF:1:C00000:0:0:0:
5. Add the new stream link to your channel list (for example with DreamBoxEdit)
IMPORTANT:
Do NOT use the correct Transponder ID/Network ID/Namespace for the stream link.
Use Transponder ID: "11", Network ID: "22" and Namespace: "33".
Set Service Type to "1", and enter the correct Service ID for the channel.
Note:
When using DreamBoxEdit:
A. Go to the list in the middle "Bouquet details".
B. Right click on a channel, select "IPTV and other streaming services", select "Add".
C. Select "DVB/TS".
D. Chosse a name and use the new stream link as URL.
E. Use the "Service ID" of the original channel. You can find it in the left list ("Services")
http://www.sat-universe.com/showthread.php?t=294230
update the Key, restart OScam and configure stream relay
IMPORTANT:
The stream relay needs a fast CPU. Not every STB is fast enough.
If you cannot fix stuttering with the following guide, likely your CPU is
too slow.
For best performance, the "Include ECM in http streams" setting must be enabled.
If your image supports it (openpli, openatv), you can find it here:
OpenWebif -> Settings -> Customize
If the setting is not available, you may need to adjust the "ECM fix delay"
setting in oscam webif (Config -> Stream Relay).
Increase/Lower it until there is no stuttering.
When using VU+ devices, make sure to use the latest drivers (June 2015), if
you encounter any problems.
Channel Config:
1. Go to the OpenWebif and click on the "Stream" button for the channel you want to add.
2. Download and save the .m3u file.
3. Open the .m3u file with a text edior and get the stream link. It looks like this:
http://stb:8001/1:0:19:0123:3EF:1:C00000:0:0:0:
4. Replace the port (8001) with the relay port (default: 17999) and the host name ("stb") with 127.0.0.1
http://127.0.0.1:17999/1:0:19:0123:3EF:1:C00000:0:0:0:
5. Add the new stream link to your channel list (for example with DreamBoxEdit)
IMPORTANT:
Do NOT use the correct Transponder ID/Network ID/Namespace for the stream link.
Use Transponder ID: "11", Network ID: "22" and Namespace: "33".
Set Service Type to "1", and enter the correct Service ID for the channel.
Note:
When using DreamBoxEdit:
A. Go to the list in the middle "Bouquet details".
B. Right click on a channel, select "IPTV and other streaming services", select "Add".
C. Select "DVB/TS".
D. Chosse a name and use the new stream link as URL.
E. Use the "Service ID" of the original channel. You can find it in the left list ("Services")
tr-aliveli
Registered
- Messages
- 2
friends. I am using my dm800hd openpli to watch discovery networks on Astra4A without stream relay without any problem. I also have a wetek play. I installed Mnigma with oscampowervu 11212 patched softcam also Openatv 5.3 with oscampvu 11213 patched. But I couldn't wacth any channels via stremrelay.
I enabled "Include ECM in http streams" from Webif.
It says "ecm" found but no any picture via stream relay.
Please check my logs and tell me a solution.
Thank you very much.
These are 2 logs from Mnigma and Openatv;
I enabled "Include ECM in http streams" from Webif.
It says "ecm" found but no any picture via stream relay.
Please check my logs and tell me a solution.
Thank you very much.
These are 2 logs from Mnigma and Openatv;
first read this http://www.sat-universe.com/showthread.php?t=285415 and try to find what are you missing,or what you are doing wrong.
i think that a newest oscam version,will solve the problem...
Hi experts.. Pls i need basic guidance cum oscam files to run power vu in newenigma2...,pls help me....my box is dreambox 800,se sim2.2,a88,v2..which oscam version is best suitable for thi image...
If i install any oscam from add on server... Will it be configure for powervu...
Regards
If i install any oscam from add on server... Will it be configure for powervu...
Regards
Hi guys!I tried many times...but i cant open the discovery channel& animal planet channel on 1w and 4.8e!
I'd like to ask you a favour.Could you post the your softcam.key?It's absurd...Hw can i fix it?Repeat...i tried many times...
My box is Edision OS mini.
I'd like to ask you a favour.Could you post the your softcam.key?It's absurd...Hw can i fix it?Repeat...i tried many times...
My box is Edision OS mini.
medousa89
Registered
- Messages
- 36
Hi guys!I tried many times...but i cant open the discovery channel& animal planet channel on 1w and 4.8e!
I'd like to ask you a favour.Could you post the your softcam.key?It's absurd...Hw can i fix it?Repeat...i tried many times...
My box is Edision OS mini.
please visit this
i have a vu+zero and pack hbo and cinemax from 4w its open without streamrelay. i use oscam emu r11272 and my image its openpli 4
Could you point me to the Tutorial? I'm hoping to get this to work for both BISS and PowerVU using "AZbox Me" and OpenATV 5.3.