help azbox hd blocked booting

R

romix

Registered
Messages
2
I installed the new version e2 test. and wanted to return to Official Firmware and instead put 0.9.5020 0.9.4466 and I think I put blade crashed I can not connect anything to the box or with azup not take any USB Booting write and so I built remains Com interface TX RX I started putty Speed 115200 azbox start and end there and not give terminal UUU

You will need:
TFTPD32
backup_kernel
putty
Serial interface for connecting to AZBox

You should know that your computer's IP address, you can find by entering the command PROMT,
means that you're going to start and run type cmd in the box and press ENTER, then type ipconfig and enter and get information about IP address
Assuming the computer's IP address: 192.168.1.12 (required below)
In this case, we choose to rank AZBox IP address where your computer's IP, we say: 192.168.1.34

1.Pokrenite TFTPD32
2.Start Putty, switch to the serial COM port where you enter the serial interface connector, enter the speed of 115200
3.Povezite serial interface and turn AZBox AZBox
4.Pratisnite CTRL C to stop bootiranje
5.kucajte:

y.ipaddr setxenv "192.168.1.34"
y.gateway setxenv "192.168.1.1"
y.subnetmask setxenv "255.255.255.0"
net init
b-load tftp: / / 192.168.1.12/backup_kernel 0xb0100000
pflash write 0xb0100000 0x680000 0x80000-f

Now, wait until the first flash contours, then enter new content.
This takes about 5-6minuta, patience to complete and eventually you rebootajte AZBox.
If everything went well, you get on TV in a standard update that you know,
insert USB stick-man and ubacitega Official FW before.
 
U

underscore

Registered
Messages
19
I don't need all those staff.I had the same problem just yestrday with e2 image.

Use azup like this:
- put original image on usb pen drive
- restart the azbox with pen on it and when it goes on resque mode you will see the IP on VDF.
- Start azup with update and you will have the origina boot on.

After automatic restart use the standart upload as azbox firmware.

Just a nore tip,dont use small pen drive,when installing the azup use a pendrive as temp file store and if is small you will get "unsupported firmware".
 
Last edited:
E

elgeneral

Well Known Member
Messages
7,811
BOOTING PROBLEM FIX !!!

After making flash, please imidiatelly go in RESCUE MODE ( Reboot box with USB Memory stick with patch.bin file inserted in RECEIVER ).

Telnet and FTP username and password are :

username: root

password: azbox

After RESCUE MODE show You IP of Your receiver , use putty and telnet to it and type this commands :

mkdir /D

mount /dev/hda1 /D

Connect with FTP to Your Reciever, and go :

/D/etc/init.d and place this bootup file which is there.

Overwrite : YES

Eject USB, Turn off and Turn on Your receiver and all will be ok.
 
D

datoamo

Registered
Messages
1
Got problem...

I did login with PuTTY but after that can't do any of your written steps. Is there any better explanation of these steps?


elgeneral said:
BOOTING PROBLEM FIX !!!

After making flash, please imidiatelly go in RESCUE MODE ( Reboot box with USB Memory stick with patch.bin file inserted in RECEIVER ).

Telnet and FTP username and password are :

username: root

password: azbox

After RESCUE MODE show You IP of Your receiver , use putty and telnet to it and type this commands :

mkdir /D

mount /dev/hda1 /D

Connect with FTP to Your Reciever, and go :

/D/etc/init.d and place this bootup file which is there.

Overwrite : YES

Eject USB, Turn off and Turn on Your receiver and all will be ok.
Click to expand...
 
You must log in or register to reply here.
Top