hi guys, I have DM600 which was working fine, however recently I was trying to play with other images, first I try to upload (using dream up via serial cable) PCD2E working, and after complete flashing, the blue screen appear says starting (forever), then tried to put original gemini, after completed, Red/Green light ON, and nothing happened, then Back to original manufacture latest image, still Two Red & Green light stays in the box Forever.. Any Sugestion, Thanks all
Dreambox DM600 failed after flashing image
- Thread starter azzy
- Start date
I would like to update the prorgress of the DM600 failures
here is what I did
1. Identifying IP address:
a. press start menu
b. click run then type cmd
c. Type ipconfig /all
inside that MSDOS command,
d. you should see the ip address (after Ethernet adapter wireless network, in my case i use wireless) it shows ip address 192.abc.def.g (g could be 1 or 2, 3 etc)
e. Write down on note pad that first 3 series 192.abc.def.g (your box should be other than g, my case it is 3
2. Working with Drambox
a. Connect serial port
b. Connect power cable
c. Connect Lan Cable from Lan port on your PC / Laptop to DM Lan connector
d. Open Dreamup software i use DreamUP_1_3_3_6.exe (tick ip & identify both IP & Box IP)
e. Press connect (the dream up ask to power on)
f. in my case power not working, I had to remove cable
g. then the flash loading.
h. next I open firefox browser and type 192.abc.def.13
New problem arise, the page is showing this PAGE
This is the DM600PVR bootloader Web Interface.
[PICTURE OF IBM POWERPC Processor]
If you see this, your box didn't boot to Linux.
Unless you interrupted the boot process, this usually means that you have no valid operating system in flash.
Don't panic! It's not a problem. You can just flash a new version and everything will be fine!
Otherwise, you can boot from network or compact flash. (Sollte jetzt gehen, wurde aber noch *nie* getestet! Nicht wundern wenns nicht geht!)
If you're about to give up, you might get help at the Dream Multimedia Support board!
Currently there aren't many other features...
You can download your current flash contents (64 MB) here, but please don't expect to be able to flash it back. It's merely a debugging feature.
This device's Serial Number is 10476, and was built on 2007/09/27.
Booloader version: Dreambox Second Stage Loader BUILD #53, built 20070827
device info firmware upgrade
Uploaded many image from original latest version, previous version, etc did not help,
one image work was "PCDE2working" but keep on restarting to the same page on the screen, otherwise all cases screen blank
After reviewing all cases, new method was introduced
I type CMD
then type TELNET
then type o/ 192.abc.def.13
and new windows (identical with BIOS Setup)
in this case, I review but dont know what to do
So STILL STUCKED ?? APpreciate if anyone can help
here is what I did
1. Identifying IP address:
a. press start menu
b. click run then type cmd
c. Type ipconfig /all
inside that MSDOS command,
d. you should see the ip address (after Ethernet adapter wireless network, in my case i use wireless) it shows ip address 192.abc.def.g (g could be 1 or 2, 3 etc)
e. Write down on note pad that first 3 series 192.abc.def.g (your box should be other than g, my case it is 3
2. Working with Drambox
a. Connect serial port
b. Connect power cable
c. Connect Lan Cable from Lan port on your PC / Laptop to DM Lan connector
d. Open Dreamup software i use DreamUP_1_3_3_6.exe (tick ip & identify both IP & Box IP)
e. Press connect (the dream up ask to power on)
f. in my case power not working, I had to remove cable
g. then the flash loading.
h. next I open firefox browser and type 192.abc.def.13
New problem arise, the page is showing this PAGE
This is the DM600PVR bootloader Web Interface.
[PICTURE OF IBM POWERPC Processor]
If you see this, your box didn't boot to Linux.
Unless you interrupted the boot process, this usually means that you have no valid operating system in flash.
Don't panic! It's not a problem. You can just flash a new version and everything will be fine!
Otherwise, you can boot from network or compact flash. (Sollte jetzt gehen, wurde aber noch *nie* getestet! Nicht wundern wenns nicht geht!)
If you're about to give up, you might get help at the Dream Multimedia Support board!
Currently there aren't many other features...
You can download your current flash contents (64 MB) here, but please don't expect to be able to flash it back. It's merely a debugging feature.
This device's Serial Number is 10476, and was built on 2007/09/27.
Booloader version: Dreambox Second Stage Loader BUILD #53, built 20070827
device info firmware upgrade
Uploaded many image from original latest version, previous version, etc did not help,
one image work was "PCDE2working" but keep on restarting to the same page on the screen, otherwise all cases screen blank
After reviewing all cases, new method was introduced
I type CMD
then type TELNET
then type o/ 192.abc.def.13
and new windows (identical with BIOS Setup)
in this case, I review but dont know what to do
So STILL STUCKED ?? APpreciate if anyone can help
I would like to update the new information on DM600 Failed; the following images were feed in to the box:
- dm600pvr-20090722.nfi original image
- dreambox-image-dm600pvr-20090803123143.nfi
- dreambox-image-dm600pvr-20100713093115.nfi
- gemini-470-dm600pvr-200912120241.nfi
- PCDE2working.nfi
- SifTeam-1.9.4C-600pvr.nfi
- PB_ENIGMA_600_V4.nfi
Only PB_ENIGMA_600_V4.nfi that is working NOW
good luck for those who want to spend time trying different images
- dm600pvr-20090722.nfi original image
- dreambox-image-dm600pvr-20090803123143.nfi
- dreambox-image-dm600pvr-20100713093115.nfi
- gemini-470-dm600pvr-200912120241.nfi
- PCDE2working.nfi
- SifTeam-1.9.4C-600pvr.nfi
- PB_ENIGMA_600_V4.nfi
Only PB_ENIGMA_600_V4.nfi that is working NOW
good luck for those who want to spend time trying different images