I jsut tested PB Enigma II Latest for dm800
Scanned satellites and rebooted and it goes into an everlasting loop, booting 50% then loop.'
I connected with teraterm to see whats happening, but i cant see anything.. Can any of you Pro's ?
Hopefully it gets readable here...
Here is the log :
c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}
2ND STAGE OK, build #84D(2011-09-02)
0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
1.100 - load config
dCA: not existent, loading defaults
1.130 - config loaded.
* press to enter setup
OLED found!
lcd: BOOT #84D
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /boot/bootlogo-dm800.elf.gz
bootlogo size: 162242
Supported modes: NTSC !NTSC_J !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K
!PAL_I !PAL_M !PAL_N !PAL_NC !SECAM 1080i !1080p 720p 480p 1080i_50Hz 1080p_24Hz
1080p_30Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p DVI_800x600p DVI_1024x7
68p DVI_1280x768p DVI_1280x720p_50Hz DVI_1280x720p DVI_1280x720p_ReducedBlank !D
VI_640x480p_60Hz !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_6
40x480p_85Hz !DVI_1280x720p_60Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_12
80x720p_75Hz !DVI_1280x720p_85Hz
best supported mode is 18
using 1920x1080i (50.00 Hz)
HDMI
using colorspace: 1
create surface 1920 1080
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@sail
lard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-2.6.18-7.4-dm800.gz
<5>Linux version 2.6.18-7.4-dm800 (image@linux) (gcc version 4.6.4 20120303 (pre
release) (GCC) ) #1 Tue Oct 15 20:10:17 CEST 2013
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null quiet
2 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null qui
et
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
