DM800 hd sim 201

S

satguy7

Member
Messages
72
Hi guys, im trying to install a new image via browser,

but when i get to page in browser locate image, then click flash
it just sits there. doesnt flash

the image im trying to use is:

GP3-dm800-2013-ramiMAHER

is the above ok and should it just work?

maybe firewall or something stopping it?
 
Ferret

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,550
Could be the firewall but id try other browsers too.

IE is usually the best for browser flashing.
 
S

satguy7

Member
Messages
72
thanks for reply. yeah disabled kaspersky, and tried in both chrome and explorer, still kinda just sits there
 
S

satguy7

Member
Messages
72
downloaded flash file ok from dm800 but wont write,

tried chrome, explorer, and just tried firefox all just sit there :eek:
 
Last edited:
S

satguy7

Member
Messages
72
Ferret said:
Well it looks like a outgoing connection fault could be something in the router.

Same problem here

http://www.sat-universe.com/showthread.php?t=253356
Click to expand...

guess it was my firewall, used old computer flashed first time.

god i feel like such a newb,

normally i used vhannible motor for bouquets,

guess im doing something wrong again lol

dreamboxedit log:

Transfer complete
** Sending file "/etc/tuxbox/satellites.xml" **
Starting FTP transfer
Transfer complete
** Getting directory list /etc/enigma2/lamedb **
Starting FTP transfer
Transfer complete

but no channels (facepalm)

something to do with paths i guess
 
Ferret

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,550
If you had something like the TSpanel on you could download them.

Looks like DBE is not sending the reload command, you could after sending just pull the power and setting should load, if not check the dbe setup and make sure the reload command is enabled.
 
S

satguy7

Member
Messages
72
was going well lol, got boquests on etc

then spent some time get it to setup internal hd it failed each,

so i seen in another thread that OpenPli was great,

so i get image for dm800 here

http://openpli.org/download/

image rights to my box ok, completes fully says will reboot.

now have "error no CA"

so i find the solution

Solution:
1) Use DreamUp 1.3.3 with serial (null modem) cable
2) Choose COM1, connect, power ON DM800 and wait
3) After a few seconds the DM800 screen will come back with an IP address
4) Type in that address in IE
5) Flash first a BootLoader (ex: bl76.nfi) reboot DM800 and hold power button
7) Wait for IP to appear on DM800 screen
8)Type in that address in IE
9) Flash your desired image

have dream up but need loader bootloader 76c

can anyone help

thanks :)
 
Ferret

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,550
satguy7 said:
was going well lol, got boquests on etc

then spent some time get it to setup internal hd it failed each,

so i seen in another thread that OpenPli was great,

so i get image for dm800 here

http://openpli.org/download/

image rights to my box ok, completes fully says will reboot.

now have "error no CA"

so i find the solution

Solution:
1) Use DreamUp 1.3.3 with serial (null modem) cable
2) Choose COM1, connect, power ON DM800 and wait
3) After a few seconds the DM800 screen will come back with an IP address
4) Type in that address in IE
5) Flash first a BootLoader (ex: bl76.nfi) reboot DM800 and hold power button
7) Wait for IP to appear on DM800 screen
8)Type in that address in IE
9) Flash your desired image

have dream up but need loader bootloader 76c

can anyone help

thanks :)
Click to expand...

Yeah as you found out that is not a clone image.

Here is 76c

http://www.sat-universe.com/showpost.php?p=664871&postcount=4

But you could use later bootloader but maybe stick with what you know to get back uo and running.
 
S

satguy7

Member
Messages
72
still trying to fix lol

downloaded dream up from dream website

ver v1.3.3.4

using usb to rs232 dongle and rs232 cable to box


Click connect in dream up power box

fully uploads flash loader.

"update complete, wiating for acknowledgement.

but at this stage dream box switches back to error no ca on dislpay again.


is it possible the version of dreamup is not for clone?


thanks again for the help.
 
A

appy

Registered
Messages
7
Hi Make sure the ip address in the display is same as the browser that happened to changed the web browser to same bingo after few second flash loaded
Regards
appy
 
S

satguy7

Member
Messages
72
kit im using

usb to r3232 adaptor, rs232 cable,

first method:

click connect power dm800 - upload flash loader completes.

dreamup Status: "box is in networked HTTP mode"


front of DM800 shows ip:

"192.168.1.18"

" *** SERIAL MODE *** "


Then i click flash selct ssl76C file


Then dreamup status sticks at:

"Calculating checksum"



the only thing is dont have any computers kicking around
any more with rs232 port, i guess the usb to rs232 adaptor is the
problem.


tried entering ip in browser but doesnt load,
 
Ferret

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,550
Don't use the 76c mate there is more than that to patching images.

Use a patched image from the thread I linked to .

When the HTTP mode ip shows I just then use browser flashing as normal.

Like I say use a prepatched image.
 
S

satguy7

Member
Messages
72
Ferret said:
Don't use the 76c mate there is more than that to patching images.

Use a patched image from the thread I linked to .

When the HTTP mode ip shows I just then use browser flashing as normal.

Like I say use a prepatched image.
Click to expand...

thanks mate, tried that in browser, must be because its not rs232 to rs232.
 
Ferret

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,550
If it showing a IP then I don't understand why it wont work when you use the IP in IE does it show you the firmware upgrade page ?
 
S

satguy7

Member
Messages
72
Ferret said:
If it showing a IP then I don't understand why it wont work when you use the IP in IE does it show you the firmware upgrade page ?
Click to expand...

im an idiot lolol,

i just had power cable +rs232 cable connected to dm800as i had to move box next to PC,

the penny dropped after your last post.

i had to connect ethernet cable them boom browser page worked and flashed with GP3 for now.

many many thanks for all the help mate really good of you,

the other year when i bought it i found an awesone walk through to setup usuals, i have motorised dish, obv i have complete forgot how to do it, guess will need to find walkthrough again,

again many thanks for your help.
 
Ferret

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,550
Usuals is easy

Menu-setup-service searching-Tuner config

Simple
Positioner

Then enter your coordinates
 
You must log in or register to reply here.
Top