Clarke-Tech 5000 Combo + and CCAM

T

tehu

Registered
Messages
12
Hi,

does someone know if there is a p firmware or another possibility to use CCAM with the CT 5000+ ?

Thanks for your comments...
 
R

ronald68

Registered
Messages
71
CT Connect

Connect youre reciever to a pc whith 0 modem cable, install fausto 1.39b on youre pc and make sssp active on youre reciever.
Read Fausto Client CCCam English PDF
and you can connect to a cccam server.
Good luck.

It works on mij CT 5000Combo +

GRR Ronald
 
Last edited:
R

ronald68

Registered
Messages
71
CT connect

When you run Fausto more times it will see to much providers an crash (above Ca.50)

You can ignore the not needed shares from server side ( ask the server owner to do it for you ).

You can even ask to have 2 different lines with different incoming shares.
He can even disable channels for you.

The hops doesnt matter, if its hop1 or hop2 or hop 15, as long the total dcw timeout is under 2 seconds for main systems and under 450ms for ***.

On server side can ignore like this :
F: username pass 3 0 0 { 0:0:1, 0100:0, 0500:0, 0604:0 }
This line will block all caid 0100 ( seca ) all 0500 viaccess and irdeto 0604.

Using the above example can block every provider you dont need,
example:
if you want only sexview from viaccess card 032000 to be blocked can done like this:
F: username pass 3 0 0 { 0:0:1, 0500:032000 }
 
D

DonRandy

Registered
Messages
12
ronald68 said:
When you run Fausto more times it will see to much providers an crash (above Ca.50)

You can ignore the not needed shares from server side ( ask the server owner to do it for you ).

You can even ask to have 2 different lines with different incoming shares.
He can even disable channels for you.

The hops doesnt matter, if its hop1 or hop2 or hop 15, as long the total dcw timeout is under 2 seconds for main systems and under 450ms for ***.

On server side can ignore like this :
F: username pass 3 0 0 { 0:0:1, 0100:0, 0500:0, 0604:0 }
This line will block all caid 0100 ( seca ) all 0500 viaccess and irdeto 0604.

Using the above example can block every provider you dont need,
example:
if you want only sexview from viaccess card 032000 to be blocked can done like this:
F: username pass 3 0 0 { 0:0:1, 0500:032000 }
Click to expand...

Where do i put the C: line?
 
J

jastaja

Registered
Messages
11
ronald68 said:
When you run Fausto more times it will see to much providers an crash (above Ca.50)

You can ignore the not needed shares from server side ( ask the server owner to do it for you ).

You can even ask to have 2 different lines with different incoming shares.
He can even disable channels for you.

The hops doesnt matter, if its hop1 or hop2 or hop 15, as long the total dcw timeout is under 2 seconds for main systems and under 450ms for ***.

On server side can ignore like this :
F: username pass 3 0 0 { 0:0:1, 0100:0, 0500:0, 0604:0 }
This line will block all caid 0100 ( seca ) all 0500 viaccess and irdeto 0604.

Using the above example can block every provider you dont need,
example:
if you want only sexview from viaccess card 032000 to be blocked can done like this:
F: username pass 3 0 0 { 0:0:1, 0500:032000 }
Click to expand...

how to activate sssp on ctech 5000c+, which remote type? ty
 
R

ronald68

Registered
Messages
71
activate sssp

Install 1.79p software
-> menu
-> Installation
-> Pin Code (default 0000)
-> Option
-> Serial mode, choose sssp

Gr ronald68
 
R

ronald68

Registered
Messages
71
c;line

Fausto 1.39b version has implemented cccam just jet.
You have to put in a f: line in menu client -> configuration.
Read Fausto & cccam pdf use example on page 2 not page 1
Dont forget to rename Fausto clients Example.Cfg to Fausto clients.Cfg
Then you can connect to cccam server
Files are now in this section (ct connect)

Gr Ronald
 
Last edited:
R

robertjust

Registered
Messages
86
ronald68 said:
Fausto 1.39b version has implemented cccam just jet.
You have to put in a f: line in menu client -> configuration.
Read Fausto & cccam pdf use example on page 2 not page 1
Dont forget to rename Fausto clients Example.Cfg to Fausto clients.Cfg
Then you can connect to cccam server
Files are now in this section (ct connect)

Gr Ronald
Click to expand...

Sorry for my english but you're talking about Clarke tech and Diablo or only with Clarke Tech that is possible the cs with sssp router etc??
 
R

ronald68

Registered
Messages
71
Diablo

I tested whith internal cardreader from CT 5000 c+
SSSP-> PC (fausto 1.39b)-> CCCam server (dreambox)
Canaldigital (NL) and Premiere (DE) works OK
In Fausto is also setup For diablo possible.
I dit not test this (i have no diablo)

Gr ronald68
 
R

robertjust

Registered
Messages
86
ronald68 said:
I tested whith internal cardreader from CT 5000 c+
SSSP-> PC (fausto 1.39b)-> CCCam server (dreambox)
Canaldigital (NL) and Premiere (DE) works OK
In Fausto is also setup For diablo possible.
I dit not test this (i have no diablo)

Gr ronald68
Click to expand...

Sorry but I am new with cs. I can only calrke tech 5000C plus do cs? And if so, can you tell me how or where can I find documentation?:eek:
Thk.
 
P

pigeone

Registered
Messages
414
ronald68 said:
I tested whith internal cardreader from CT 5000 c+
SSSP-> PC (fausto 1.39b)-> CCCam server (dreambox)
Canaldigital (NL) and Premiere (DE) works OK
In Fausto is also setup For diablo possible.
I dit not test this (i have no diablo)

Gr ronald68
Click to expand...


What made the connection with the CT 5000 c + with ineternet, or the pc com port ?
 
R

ronald68

Registered
Messages
71
CT connect

The pc connects to internet.
Info in this section.
Also see post: ct connect -> pdf. file
 
R

robertjust

Registered
Messages
86
ronald68 said:
The pc connects to internet.
Info in this section.
Also see post: ct connect -> pdf. file
Click to expand...

Sorry again, I want to be sure. But faustoclients.cfg need to be able to do CS with my card in my home or you can take the cards from outside of your home??
I have problem to config faustoclients.cfg .... user pass etc.
Help me in pm.
Sorry my bad english.:(
 
R

ronald68

Registered
Messages
71
Out home

Fausto can connect to anywhere over the internet (ethernet)
With server (card)
Whats youre problem wit config?

Example that works:

##########################################################################################################
# syntax for CCcam Client connection
# F: IP PORT WANTEMU USERNAME PASSWORD {CAID-4 byte len/PROVIDS-6 bytes len}
# WANTEMU=0 Disable CCCam Emu on sharing
# WANTEMU=1 Enable CCCam Emu on sharing
# example:
# F: 127.0.0.1 9000 1 dummy dummy


F: kallo789.no-ip.kiz 14000 0 donald 14333 (i changed F line in detial for privecy)

Gr ronald68
 
Last edited:
R

robertjust

Registered
Messages
86
ronald68 said:
Fausto can connect to anywhere over the internet (ethernet)
With server (card)
Whats youre problem wit config?

Example that works:

##########################################################################################################
# syntax for CCcam Client connection
# F: IP PORT WANTEMU USERNAME PASSWORD {CAID-4 byte len/PROVIDS-6 bytes len}
# WANTEMU=0 Disable CCCam Emu on sharing
# WANTEMU=1 Enable CCCam Emu on sharing
# example:
# F: 127.0.0.1 9000 1 dummy dummy


F: kallo789.no-ip.kiz 14000 0 donald 14333 (i changed F line in detial for privecy)

Gr ronald68
Click to expand...

I have to change the faustoclients.cfg:
-Only f: Kallo ......?

-F: Kallo is the address for take the key out door for cs?

-The rest of faustoclients not be changed?

-My address and port do not need to insert in?

I am new to cs.(and see:D)

Thank you.

Robertjust
 
Last edited:
You must log in or register to reply here.
Top