Instruction of burn loader
=========================
1: Install AIi_usb_driver into PC.
( Pls find the file of “ How to set up the driver for J-Tag, and follow the way to install the driver. )
2: Make sure the 6 pin Plug for J-Tag conncetion has soldered on main board. Pls find its position of E JTAG marked on the main board.
Make sure the 2 pin Plug ( JP1 ) for short-cut connection has soldered on main board.
You could use a Conductor, for example a Plier to make the Receiver in short-cut mode, that is ok.
Pls make sure the above condition is ok, and then pls go to below procedure.
3:*Put the file Burn_tool in Drive D:
4: Decompress the Burn-tool file into current folder in Drive D, and then the file name would be Burn_tool
5: Open the file Bure_tool, put the new software into this file "Burn_tool"
And then pls*do remember to change the name for this software as "product_rock_3329c_sdk.abs".
The software name has been changed to “product_rock_3329c_sdk.abs" as below pictures shows.
Pls go to next step directly.
Remark: Pls always change the software name in such .abs format if you use any new software.
( The software could not be detected and download if you do not change the file name in this way. If the software could not be detected, pls check the software name, and correct it. )
Remark: The file "Need_file" is a data file, pls keep it still, don't move this file away, or you can't update the software according to our attached burn_tool.
6: connected J-Tag with PC via USB cable:
And then connected J-Tag with DVB by 6 pin plug ( on EJTAG )
Pls pay attention to the plug port direction, if you could not connect the plug well, pls turn to the opposite direction.
7: power off the DVB, and then make the DVB in short-cut mode by connected the two pin plug ( on JP1 ).
And then power on the DVB. Then remove the short-cut tool ( Plier ) after 3~5 second
8: Dblclick the file "Burn_3329C.bat", the updating will begin at once.
** The relative information will be showed on the PC.
9: When there are some character string such as “ Burn 001F0000 OK, Terminate monitor thd, wait monitor thd "
on the screen, that shows the updating is finished.
*
10: After finished the above procedure, the Flash redownload is successful, pls power off the DVB, and then remove the short-circuit, and disconnect the J-Tag from DVB, then everything is ok, the software will work accordingly.
Note: If fail burn loader, pls reconnect the J-tag and retry.
=========================
1: Install AIi_usb_driver into PC.
( Pls find the file of “ How to set up the driver for J-Tag, and follow the way to install the driver. )
2: Make sure the 6 pin Plug for J-Tag conncetion has soldered on main board. Pls find its position of E JTAG marked on the main board.
Make sure the 2 pin Plug ( JP1 ) for short-cut connection has soldered on main board.
You could use a Conductor, for example a Plier to make the Receiver in short-cut mode, that is ok.
Pls make sure the above condition is ok, and then pls go to below procedure.
3:*Put the file Burn_tool in Drive D:
4: Decompress the Burn-tool file into current folder in Drive D, and then the file name would be Burn_tool
5: Open the file Bure_tool, put the new software into this file "Burn_tool"
And then pls*do remember to change the name for this software as "product_rock_3329c_sdk.abs".
The software name has been changed to “product_rock_3329c_sdk.abs" as below pictures shows.
Pls go to next step directly.
Remark: Pls always change the software name in such .abs format if you use any new software.
( The software could not be detected and download if you do not change the file name in this way. If the software could not be detected, pls check the software name, and correct it. )
Remark: The file "Need_file" is a data file, pls keep it still, don't move this file away, or you can't update the software according to our attached burn_tool.
6: connected J-Tag with PC via USB cable:
And then connected J-Tag with DVB by 6 pin plug ( on EJTAG )
Pls pay attention to the plug port direction, if you could not connect the plug well, pls turn to the opposite direction.
7: power off the DVB, and then make the DVB in short-cut mode by connected the two pin plug ( on JP1 ).
And then power on the DVB. Then remove the short-cut tool ( Plier ) after 3~5 second
8: Dblclick the file "Burn_3329C.bat", the updating will begin at once.
** The relative information will be showed on the PC.
9: When there are some character string such as “ Burn 001F0000 OK, Terminate monitor thd, wait monitor thd "
on the screen, that shows the updating is finished.
*
10: After finished the above procedure, the Flash redownload is successful, pls power off the DVB, and then remove the short-circuit, and disconnect the J-Tag from DVB, then everything is ok, the software will work accordingly.
Note: If fail burn loader, pls reconnect the J-tag and retry.