How to use vPlug Server.
1. Find what is your PC IP address via cmd "ipconfig"
2. We have to add "Softcam.Key" to root folder where we have vPlug Server. Due to we added Softcam.Key to root folder, vPlug Server will read keys automatically from Softcam.Key and not from v_keys.db.
3. Of course we must add "Tandberg.mdl" to "vModules" folder for decoding Tandberg channels.
4. Run vPlug Server and click to "vPlug Server Options" and edit IP address of "CCCam Server IP". You can leave "CCcam Server Port" as it is (12000). Now you can click to "CCCam Server active" and click to "Save"
5. Now we have running CCCam Server, but we have to add some keys to vPlug Server. So, if you want to use it for Tandberg, you have to add a new card with CAID 1010, so click to "Edit CARD(s)" and later click to "Add card" and set card name ("Tandberg" for example).
6. Now we must fill in some informations:
- Card CAID: 1010
- ProviderID(s): 000000
- Comment: (only if you want.. You can fill in "Tandberg" again. It's just only for information)
At the end don't forget to click to "Save"
7. If we already have Tandberg keys (classic key format "T 2705 01 xxxxxxxxxxxxxx00") in Softcam.Key, we can just connect receiver to vPlug Server. Just add cline to your favorite emulator (I preffer mgcamd).
8. If we will use mgcamd, we have to add cline to "cccamd.list" and set correct value in "mg_cfg"
cccamd.list:
mg_cfg: you have to set mgcamd to reading from cccam, so set "G: { 33 }" for best config.
9. Now you can just run mgcamd and tune Tandberg channel and it should decoding Tandberg channels. Due to all Tandberg's feeds are off we can't test it but if you do all stepts correctly, you can just wait for Tandberg feeds. :thum:
(Sorry for my bad English)
1. Find what is your PC IP address via cmd "ipconfig"
2. We have to add "Softcam.Key" to root folder where we have vPlug Server. Due to we added Softcam.Key to root folder, vPlug Server will read keys automatically from Softcam.Key and not from v_keys.db.
3. Of course we must add "Tandberg.mdl" to "vModules" folder for decoding Tandberg channels.
4. Run vPlug Server and click to "vPlug Server Options" and edit IP address of "CCCam Server IP". You can leave "CCcam Server Port" as it is (12000). Now you can click to "CCCam Server active" and click to "Save"
5. Now we have running CCCam Server, but we have to add some keys to vPlug Server. So, if you want to use it for Tandberg, you have to add a new card with CAID 1010, so click to "Edit CARD(s)" and later click to "Add card" and set card name ("Tandberg" for example).
6. Now we must fill in some informations:
- Card CAID: 1010
- ProviderID(s): 000000
- Comment: (only if you want.. You can fill in "Tandberg" again. It's just only for information)
At the end don't forget to click to "Save"
7. If we already have Tandberg keys (classic key format "T 2705 01 xxxxxxxxxxxxxx00") in Softcam.Key, we can just connect receiver to vPlug Server. Just add cline to your favorite emulator (I preffer mgcamd).
8. If we will use mgcamd, we have to add cline to "cccamd.list" and set correct value in "mg_cfg"
cccamd.list:
Code:
C: ip_pc_address 12000 user1 pass1 #(user1 and pass1 are default values. You can change it too, but you can leave it as it is...)mg_cfg: you have to set mgcamd to reading from cccam, so set "G: { 33 }" for best config.
Code:
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccam netclient
# 33 cccam newcamd netclient
G: { 33 }9. Now you can just run mgcamd and tune Tandberg channel and it should decoding Tandberg channels. Due to all Tandberg's feeds are off we can't test it but if you do all stepts correctly, you can just wait for Tandberg feeds. :thum:
(Sorry for my bad English)
Last edited:
