|
#1
|
|||
|
|||
![]() Hi
i have vu + solo 2 time bomb bricked receiver trying to recover with j tag BBS cypress device i have j tag flash file downloaded from vu-hd.com installed broadband studio 3 and bcm 97346 after that successfully connected to samsung flash K9F2G08U0C and also downloaded flash file 100% but still only light on front pannel no usb port working. one thing i have noticed that when i flashed box with flash file and box unsuccessful for start and i am trying to connect with broadband 3 bcm it was connected but when trying to connect with flash K9F2G08U0C it shows i/o error and couldnot detect flash after that many time i pressed refresh button some time 7 some time 8 and some time 6 then it was detect flash after that i was perform erase entire flash then easily it will detect the flash ic i could not under stand what is this i think boot loader is wrong for this box The Chip is K9F2G08U0C and the board is Lonrisun. |
The Following User Says Thank You to starfox1 For This Useful Post: | ||
WAC2504 (13-02-2018) |
#2
|
||||
|
||||
![]() Try this bootloader mate.
But that input output error could mean the nand is write protected or faulty.
__________________
![]() VU+ Duo2 Japhar DM8000 A8P DM800SE Amazon Fire TV Box 2nd Gen T95Z Plus S912 3GB+16GB TX3 Mini |
#3
|
|||
|
|||
![]() Quote:
now two case: first if the nand is write protected is their a way to remove the protection? if the answer is no: and the nand is faulty can i replace it with empty one and reflash with the same bootloader? thanx in advance Ferret |
#4
|
||||
|
||||
![]() Quote:
If that does not work there is a problem with the nand and it needs replacing.
__________________
![]() VU+ Duo2 Japhar DM8000 A8P DM800SE Amazon Fire TV Box 2nd Gen T95Z Plus S912 3GB+16GB TX3 Mini |
#5
|
|||
|
|||
![]() Will this work for vu+ solo2 clone about a year old Nov 2013 ish
|
#6
|
|||
|
|||
![]() Quote:
Because my solo 2 is stopped at VFD writes starting on VFD. |
#7
|
||||
|
||||
![]() Quote:
But starting on display probably means the bootloader is ok i take it you tried a simple reflash ?
__________________
![]() VU+ Duo2 Japhar DM8000 A8P DM800SE Amazon Fire TV Box 2nd Gen T95Z Plus S912 3GB+16GB TX3 Mini |
The Following User Says Thank You to Blade For This Useful Post: | ||
Robertooo (16-11-2017) |
#8
|
|||
|
|||
![]() Quote:
I've got a problem with my original solo 2. I've used open pli 4 and I tried to update it online. But after rebooting the VFD writes starting only and stops here. I've tried to install open pli 4 from pendrive, my backup from pendrive but it doesn't recognize it and VFD writes only starting. The led of the pendrive is twinkles about 5-10 secs after power on and 10 secs later it burns continuously. /Sorry for my bad English./ |
#9
|
||||
|
||||
![]() That bootloader is no good ill try find you correct one.
__________________
![]() VU+ Duo2 Japhar DM8000 A8P DM800SE Amazon Fire TV Box 2nd Gen T95Z Plus S912 3GB+16GB TX3 Mini |
The Following User Says Thank You to Blade For This Useful Post: | ||
Robertooo (16-11-2017) |
#10
|
||||
|
||||
![]() Ive just fond this info else where by Aliraza63 try this with the attached files.
I have used the method according to instruction and luckly recoverd back my Solo 2 and my Friends Solo2 Se . Both boxes are working fine For other members I m pasting pics and Files set for the forum. 1. First of All Install Mcu_ Flash file With the RS-232 Cable from the folder 2. Switch off the Receiver 3. Open Hyper terminal 4. According to PDF guide Connect and load the boot laoder in this folder 5. After Successfull Complete Just Uplaod any Safe Image with Usb . ![]() ![]()
__________________
![]() VU+ Duo2 Japhar DM8000 A8P DM800SE Amazon Fire TV Box 2nd Gen T95Z Plus S912 3GB+16GB TX3 Mini |
![]() |
Thread Tools | |
Display Modes | |
|
|