Tutorial: All settings vPlug_Server_v1.0.2.21 -Hadu -Tandberg by shishmish

jan55

Member
Messages
4,266
for me vPlug_Server (Tandberg) with oscam&cccam work very well via camd35 protocol and open all channels (Arena's, MDS, ...) :thum:
 

saul

Registered
Messages
15
Can you post your CCcam.cfg and vPlug_Server.xml files?

Thanks for your interest.
Here you are.

CCcam.cfg
C: 192.168.0.10 12002 user1 pass1
SERVER LISTEN PORT : 12002
WEBINFO USERNAME : user
WEBINFO PASSWORD : pass

vPlug_Server.xml
<vPlug_Server>
<section name="CCcam Server">
<ident name="Version">2.3.0</ident>
<ident name="Port">12002</ident>
<ident name="Active">1</ident>
<ident name="IP">192.168.0.10</ident>
</section>
<section name="General">
<ident name="Debug module">1</ident>
<ident name="Log DCW">1</ident>
<ident name="Log TCP Transfer">1</ident>
<ident name="ECM cache size">30</ident>
<ident name="EMM cache">1</ident>
<ident name="EMM rewrite">3</ident>
<ident name="Log To File">1</ident>
<ident name="Log To File Separate">0</ident>
<ident name="WebServer IP">192.168.0.10</ident>
<ident name="WebServer Port">81</ident>
<ident name="WebServer Active">1</ident>
<ident name="CCcam Extended Functions"></ident>
<ident name="StartUp Delay">0</ident>
</section>
<section name="User">
<ident name="User name">user1</ident>
<ident name="Pass">pass1</ident>
<ident name="ReShare">3</ident>
<ident name="AU Enabled">1</ident>
</section>
<section name="CARD" caid="1010" card_name="Tandberg">
<ident name="Comment">Tandberg 7E_10E</ident>
<ident name="ProviderID">000000,000001,000002,000003,000004,000005,00000C,000083,000084,0000C9,0000CA,0003E8,0003E9,0003EA,0003EB,0003EC,0003ED,000691,0006A4,0006AB,000A26,001600,0016E5,001771,001773,001774,001777,001778,001959,001ED5,002140,002249,00224A,002705,002706,00270D,002710,00FFFF</ident>
<ident name="max Good SIDs">255</ident>
<ident name="Good SID"></ident>
<ident name="Bad SID"></ident>
</section>
<section name="CARD" caid="0500" card_name="Viaccess">
<ident name="Comment">Mezzo</ident>
<ident name="ProviderID">007400</ident>
<ident name="max Good SIDs">255</ident>
<ident name="Good SID"></ident>
<ident name="Bad SID"></ident>
</section>
<section name="camd3 UDP Server">
<ident name="IP">192.168.0.10</ident>
<ident name="Port">5555</ident>
<ident name="Active">0</ident>
</section>
</vPlug_Server>

But I don't know if there need to change something also on CCcam.providers or other files.
Thanks again.
 

empb

SU Team: It's All Good (Fausto v1.45/Newcamd/vplug
Staff member
Administrator
Messages
10,231
This vplug server set up is working perfect for me with CCCam & Technomate (as is Fausto EMU).
 

percivjr

Registered
Messages
461
I can't see anything obviously wrong.

Can you connect to the CCcam web interface (look for WEBINFO LISTEN PORT in CCCam.cfg and point a browser to that port on your Dreambox).

Do you see your vPlug_server IP address under the 'Servers' tab and Tandberg listed under the 'Shares' and 'Providers' tabs?

Also, you can start CCcam with the -d option and see its log on the console. Does that show anything interesting when you switch to a Tandberg channel?
 

saul

Registered
Messages
15
I can't see anything obviously wrong.

1. Can you connect to the CCcam web interface (look for WEBINFO LISTEN PORT in CCCam.cfg and point a browser to that port on your Dreambox).

2. Do you see your vPlug_server IP address under the 'Servers' tab and Tandberg listed under the 'Shares' and 'Providers' tabs?

3. Also, you can start CCcam with the -d option and see its log on the console. Does that show anything interesting when you switch to a Tandberg channel?

1. Yes
2. Yes
3. similar to vPlug server's log, with info about Viaccess decryption when I select to watch Mezzo, but nothing happens when switching to a Tandberg channel :mecry:

Thanks a lot for your interest.

 

jan55

Member
Messages
4,266
try change ver. of CCcam in vPlug_Server and add in your c-line ( no { 0:0:2 }
Thanks for your interest.
Here you are.

CCcam.cfg
C: 192.168.0.10 12002 user1 pass1 no { 0:0:2 }
SERVER LISTEN PORT : 12002
WEBINFO USERNAME : user
WEBINFO PASSWORD : pass

vPlug_Server.xml
<vPlug_Server>
<section name="CCcam Server">
<ident name="Version">2.0.11</ident>
<ident name="Port">12002</ident>
<ident name="Active">1</ident>
<ident name="IP">192.168.0.10</ident>
</section>
<section name="General">
<ident name="Debug module">1</ident>
<ident name="Log DCW">1</ident>
<ident name="Log TCP Transfer">1</ident>
<ident name="ECM cache size">30</ident>
<ident name="EMM cache">1</ident>
<ident name="EMM rewrite">3</ident>
<ident name="Log To File">1</ident>
<ident name="Log To File Separate">0</ident>
<ident name="WebServer IP">192.168.0.10</ident>
<ident name="WebServer Port">81</ident>
<ident name="WebServer Active">1</ident>
<ident name="CCcam Extended Functions"></ident>
<ident name="StartUp Delay">0</ident>
</section>
<section name="User">
<ident name="User name">user1</ident>
<ident name="Pass">pass1</ident>
<ident name="ReShare">3</ident>
<ident name="AU Enabled">1</ident>
</section>
<section name="CARD" caid="1010" card_name="Tandberg">
<ident name="Comment">Tandberg 7E_10E</ident>
<ident name="ProviderID">000000,000001,000002,000003,000004,000005,00000C,000083,000084,0000C9,0000CA,0003E8,0003E9,0003EA,0003EB,0003EC,0003ED,000691,0006A4,0006AB,000A26,001600,0016E5,001771,001773,001774,001777,001778,001959,001ED5,002140,002249,00224A,002705,002706,00270D,002710,00FFFF</ident>
<ident name="max Good SIDs">255</ident>
<ident name="Good SID"></ident>
<ident name="Bad SID"></ident>
</section>
<section name="CARD" caid="0500" card_name="Viaccess">
<ident name="Comment">Mezzo</ident>
<ident name="ProviderID">007400</ident>
<ident name="max Good SIDs">255</ident>
<ident name="Good SID"></ident>
<ident name="Bad SID"></ident>
</section>
<section name="camd3 UDP Server">
<ident name="IP">192.168.0.10</ident>
<ident name="Port">5555</ident>
<ident name="Active">0</ident>
</section>
</vPlug_Server>

But I don't know if there need to change something also on CCcam.providers or other files.
Thanks again.

... you check card in vPlug_Server:
 
Last edited:

percivjr

Registered
Messages
461
but nothing happens when switching to a Tandberg channel

So 'yes' and 'yes' means that vPlug_server is working and CCcam can see it OK.

But I'd have expected to see something in the CCcam log on Tandberg. Stupid question, but are you sure that the channel is actually transmitting?!!!
 

saul

Registered
Messages
15
try change ver. of CCcam in vPlug_Server and add in your c-line -> no { 0:0:2 }


... you check card in vPlug_Server:

Yes, I'm seeing cards in vPlug server.
I have tried these changes, but with no success :mecry:
Thanks a lot in any case.
 

saul

Registered
Messages
15
So 'yes' and 'yes' means that vPlug_server is working and CCcam can see it OK.

But I'd have expected to see something in the CCcam log on Tandberg. Stupid question, but are you sure that the channel is actually transmitting?!!!


Exactly, vPlug server is working -- but only with encryption different than Tandberg :mecry: I've tried Viaccess with success.
Yes, the channel is trasmitting... I'm watching the same channel right now on PC with Skystar, using DVBDream and vPlug (I have a twin LNB in motor dish, the other end goes to STB)... but still nothing on Dreambox with CCcam connected to vPlug server.

Anyway, a big thank you for trying to help me :)
 

percivjr

Registered
Messages
461
but still nothing on Dreambox with CCcam

It's like CCcam isn't receiving the stream, since there's nothing in the log. I don't think it's a configuration problem - for example if you had set CCcam to ignore CAID 1010, the log would tell you.

I'm at a loss, sorry.
 

fiji

Member
Messages
1,074
My working Vplug server Tandberg

Info: Server [19:56:44.917] -------------------------------------------------------------------
Info: Server [19:56:44.917] Starting vPlug Server, Ver 1.0.2.21
Info: Server [19:56:45.179] Loading Drecrypt.mdl ...
Info: Server [19:56:45.179] Loaded module: Drecrypt.mdl, Version: 10/07/2014, Author: DebugProcess
Info: Server [19:56:45.179] Loading Irdeto.mdl ...
Info: Server [19:56:45.179] Loaded module: Irdeto.mdl, Version: V 1.1, Author: V
Info: Server [19:56:45.179] Loading ***.mdl ...
Info: Server [19:56:45.179] Loaded module: ***.mdl, Version: V 1.1, Author: V
Info: Server [19:56:45.179] Loading PowerVu.mdl ...
Info: Server [19:56:45.179] Loaded module: PowerVu.mdl, Version: V 1.4, Author: PowerVU CSA Test
Info: Server [19:56:45.179] Loading Seca.mdl ...
Info: Server [19:56:45.179] Loaded module: Seca.mdl, Version: V 1.3, Author: V
Info: Server [19:56:45.179] Loading Tandberg.mdl ...
Info: Server [19:56:45.179] Loaded module: Tandberg.mdl, Version: V 1.0, Author: SPC
Info: Server [19:56:45.179] Loading Viaccess.mdl ...
Info: Server [19:56:45.179] Loaded module: Viaccess.mdl, Version: V 1.4, Author: DebugProcess
Info: Server [19:56:45.489] Added 10 card(s) from XML
Info: Server [19:56:45.529] Added 0 server connection(s) from XML
Info: Server [19:56:45.529] Added 1 user(s) from XML: my name
Info: Server [19:56:46.229] CCcam server configured with version: 2.1.3, build 3165, node ID 8CB8BBAD1199158A
Info: Server [19:56:46.229] CCcam server is active on IP: my pc ip, port: my port
Info: C000001D0 [19:56:51.709] Incomming CCcam connection from: my emulator ip for comport to connect My Box
Info: C000001D0 [19:56:51.709] Login username from CCcam client C000001D0, User: my name
Info: C000001D0 [19:56:51.729] CCcam client with User: my name, Client Node ID: 2923BE84E16CD6AE, want EMUs: 0, Version: 2.1.3, Build: 3165
Info: C000001D0 [19:56:56.879] ECM request: 1010/000000/0001/C7180143 for ShareID: 00000068 I1
Info: Server [19:56:56.899] ECM decrypted by vPlug Module
Info: C000001D0 [19:56:56.909] ECM successfully decrypted by ShareID 00000068 (27) , ECM Nr.: 1
 

Robertooo

Senior Member
Messages
5,668
Does sb know why vplug server writes this error?

N_vtelen2.jpg


It doesn't allow to add or modify key in v_keys.db file.
 

jan55

Member
Messages
4,266
in vPlug Server DB Editor - you can only change or corrected keys ...
new keys you can add in new v_keys.db & SoftCam.key
 

ganihot

Registered
Messages
3
Reload new system and the return of Tandberg vid Premier ship 7E

A new system update Tandberg and new:

Tandberg Model V 1.2

- Added new nano-ED, E1 and E4 and media support.

Usage:

- Use the new `poc.exe` to find new ECM keys.

- Then update the `old Tandberg.mdl` file with the new one.

To download:
 

Tancro

Registered
Messages
1
Hi,
Can you help?
Myy spider box connects to the vplug server and then disconnects, connects and disconnects, no reason why, it starts sending data but keeps disconnecting.
Have i missed something ?
Thank you in advance.
 

resbaloso

Registered
Messages
2
Todavia se puede ver algo con la visonplus 1020a

Todavia se puede ver algo con la visonplus 1020a utilizando el protocolo newcam por iks?
Vivo en Puerto Rico y me interesa este tema, alguien puede ayudarme?
 
Top