Vantage X211SCI Return to no emu latest firmware

pss1

Registered
Messages
10
Hi friends!
Need help.
I found an Vantage X211SCI receiver at a fleamarked.
Starting it sows the follwing:
- boot
- 4444
- after power on/off, STBstarting goes to stby.
- starting to menu manualy & trying to set factory defoult
box is asking keyword.
- can´`t enter?; remote controller no reaction at all functions !!?

thats all for now !!!
are there any solutions possible ???
thanks for any answes...........pss:confused:
 
Last edited:

bonou2

Registered
Messages
375
hi @pss1

is likely to be a fault in the power suplly
so please upload 1-2 photos with power suplly from your receiver Vantage X211SCI
 

pss1

Registered
Messages
10
hi @pss1

is likely to be a fault in the power suplly
so please upload 1-2 photos with power suplly from your receiver Vantage X211SCI

I cannot post an IMG or do know howto, any sggestion?
Iam an newbe.
Thanks............pss1
 

pss1

Registered
Messages
10
Dear bonou2
I Have checked the Voltages on the Power Supply, all ok.
The 30VDC output is not active, there are no components on
the Powersupplyboard, it looks like this is willingly so
greetings-----------pss1
 

pss1

Registered
Messages
10
All Voltages are as written OK on the Powersupply
I cannot use the RCU, Box is not respondig at all.
Greetings.............pss1
 

bonou2

Registered
Messages
375
Dear bonou2
I Have checked the Voltages on the Power Supply, all ok.
The 30VDC output is not active,:mad::mad: there are no components on
the Powersupplyboard, it looks like this is willingly so
greetings-----------pss1

check these components:
C1--68uF/450V--------310V
D51,C51,C52,C62------14,8V
D61,C61----------------20V
 

pss1

Registered
Messages
10
Powersupply shows to be ok.Voltages on the outputconnector are as follows:
5V = 5,2v
3v3 = 3,5v
GND = GND
12V = 11.9v
5v? = 5,1v
6v6 = 6v
23v = 24v
16v = 17,8v
23V = 24,8v
16v = 17,8v
30v = no output, no components on the PCB to provide voltage.

What is the meaning of displaying "4444" ?
After repeating Power on/off receiver starts normal and is controllable via the frontpanel upto the point where the inputs from RCU are needed;Inputs are not recogized at all.
Is there a way to test the IR-Port of my Box ?
Thank for your replays.............pss1
 

pss1

Registered
Messages
10
Another question is, what firmware is a non-emu soft.
Operating via the frontpanel iam still finding Emusoft, where i
cant wipe the K*ys ?
Its only possible using the RCU but the RX isn`t receiving IR signals.
any suggestins ??
 

pss1

Registered
Messages
10
Another question is, what firmware is a non-emu soft.
Operating via the frontpanel iam still finding Emusoft, where i
cant wipe the K*ys ?
Its only possible using the RCU but the RX isn`t receiving IR signals.
any suggestins ??
 

pss1

Registered
Messages
10
Hi everybody!
during last night i tryed to check the IR-Sensor of the receiverusing a oscilloskope.
results: the IR-RX Diode is receiving signals from the RCU (pulspattern is visible).
On the frontpanel there is an IC named "Apllo A 06 50",where
the pulspsttern should end (assuming so).
Q:
1-is a datasheet for this IC available?
2-is sambody having a Sevicemanual or wiring(schematic)diagram ?
Asking vor help...........pss1
 
Top