Problem with 525

brippi68

Registered
Messages
561
I HAVE PROBLEM
Dreambox DM520

M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@

BCM973625A0 CFE v15.3, Endian Mode: Little
Build Date: Fri Aug 19 11:48:16 2016 (Jann@Cynric)
Copyright (C) Broadcom Corporation.

CI box detected
card if inited
Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spare Area Size=16
MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256

CPU speed: 751MHz
DDR Frequency: 1061 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 16MB
RTS VERSION: rts_hevc10_1067
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1

DM init finalization
yxml: processing file of 131072 bytes... succeeded!
no file loaded, create xml restoring default xml
loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1
[1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options
[2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options
[3] type 1, dev eth0, loader elf, filesys tftp, file , options bmem=192M@64M console=ttyS0,1000000 root=/dev/nfs ip=dhcp
added 3 sources to autoboot list
init fp
Initializing USB.

CFE initialized.
found card in unknown state
ca valid!



***** DREAMBOX SSBL *****

Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 500ms to cancel
Proceeding with autoboot.. You can try aborting with Ctrl+C

*** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf)

Ethernet link is up: 100 Mbps Full-Duplex
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:
Loading: 0x80001000/7448768 0x8071b8c0/240192 Entry address is 0x805b01a0
Closing network eth0
Starting program at 0x805b01a0

▒[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.236000] loop: module loaded
[ 0.237000] brcmstb_nand: NAND controller driver is loaded
[ 0.238000] tun: Universal TUN/TAP device driver, 1.6
[ 0.239000] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 0.361000] bcmgenet: configuring instance #0 for internal PHY
[ 0.381000] bcmgenet bcmgenet.0: (unregistered net_device): link down
[ 0.382000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.383000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.383000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 0.415000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.421000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.422000] hub 1-0:1.0: USB hub found
[ 0.422000] hub 1-0:1.0: 2 ports detected
[ 0.423000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.424000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.424000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
[ 0.425000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
[ 0.491000] hub 2-0:1.0: USB hub found
[ 0.491000] hub 2-0:1.0: 2 ports detected
[ 0.492000] Initializing USB Mass Storage driver...
[ 0.493000] usbcore: registered new interface driver usb-storage
[ 0.494000] USB Mass Storage support registered.
[ 0.494000] i2c /dev entries driver
[ 0.495000] lirc_dev: IR Remote Control driver registered, major 253
[ 0.495000] usbcore: registered new interface driver btusb
[ 0.497000] TCP: cubic registered
[ 0.497000] NET: Registered protocol family 10
[ 0.499000] NET: Registered protocol family 17
[ 0.499000] Bluetooth: RFCOMM TTY layer initialized
[ 0.500000] Bluetooth: RFCOMM socket layer initialized
[ 0.501000] Bluetooth: RFCOMM ver 1.11
[ 0.501000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.502000] Bluetooth: BNEP filters: protocol multicast
[ 0.502000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.503000] L2TP core driver, V2.0
[ 0.503000] Registering the dns_resolver key type
[ 0.504000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.506000] EBI CS2: setting up NAND flash (primary)
[ 0.507000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 512MiB 3,3V 8-bit)
[ 0.508000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
[ 0.508000]
[ 0.510000] Bad block table found at page 262080, version 0x01
[ 0.511000] Bad block table found at page 262016, version 0x01
[ 0.512000] nand_read_bbt: bad block at 0x00000a1a0000
[ 0.513000] nand_read_bbt: bad block at 0x000018260000
[ 0.513000] nand_read_bbt: bad block at 0x00001e460000
[ 0.514000] nand_read_bbt: bad block at 0x00001fca0000
[ 0.515000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.516000] 0x000000000000-0x00001f500000 : "rootfs"
[ 0.518000] 0x000000000000-0x000020000000 : "entire_device"
[ 0.520000] 0x00001f500000-0x00001fa00000 : "kernel"
[ 0.521000] EBI CS0: setting up SPI flash
[ 0.522000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
[ 0.523000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
[ 0.524000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
[ 0.525000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.527000] UBI: attaching mtd0 to ubi0
[ 0.527000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.528000] UBI: logical eraseblock size: 126976 bytes
[ 0.528000] UBI: smallest flash I/O unit: 2048
[ 0.529000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.530000] UBI: data offset: 4096
[ 3.672000] UBI: max. sequence number: 2137
[ 3.688000] UBI: attached mtd0 to ubi0
[ 3.689000] UBI: MTD device name: "rootfs"
[ 3.689000] UBI: MTD device size: 501 MiB
[ 3.690000] UBI: number of good PEBs: 4005
[ 3.691000] UBI: number of bad PEBs: 3
[ 3.691000] UBI: number of corrupted PEBs: 0
[ 3.692000] UBI: max. allowed volumes: 128
[ 3.692000] UBI: wear-leveling threshold: 4096
[ 3.693000] UBI: number of internal volumes: 1
[ 3.693000] UBI: number of user volumes: 1
[ 3.694000] UBI: available PEBs: 0
[ 3.694000] UBI: total number of reserved PEBs: 4005
[ 3.695000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 3.696000] UBI: max/mean erase counter: 3/1
[ 3.696000] UBI: image sequence number: -547881637
[ 3.697000] UBI: background thread "ubi_bgt0d" started, PID 54
[ 3.699000] ALSA device list:
[ 3.699000] No soundcards found.

[ 3.749000] UBIFS: recovery needed
[ 3.781000] UBIFS: recovery completed
[ 3.782000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs"
[ 3.783000] UBIFS: file system size: 501047296 bytes (489304 KiB, 477 MiB, 3946 LEBs)
[ 3.784000] UBIFS: journal size: 25141248 bytes (24552 KiB, 23 MiB, 198 LEBs)
[ 3.785000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 3.785000] UBIFS: default compressor: lzo
[ 3.786000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 3.788000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 3.789000] devtmpfs: error mounting -2
[ 3.789000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 3.791000] Rebooting in 180 seconds..

my lan dreambox is off
Tried with dreamup
and various programs of recoveri
I can not solve the problem
Do you have any suggestions?
 

brippi68

Registered
Messages
561
Thanks for your answer.
I have proceeded to the return and replacement of the product.
I tried to understand if it was possible to unlock the decoder
 

Tonio20

Registered
Messages
11
Hi. Your dm52o is ok
Diagnostic good
Flash via interner with image originale unstale.
Regatds
 

seened

Registered
Messages
6
Ctrl+C

CFE> ephycfg

1) Internal 10/100Mbps PHY (build-in PHY)
2) MII to external 10/100Mbps PHY (e.g. bcm53101E)
3) RGMII ID mode disabled for external 10/100/1000Mbps PHY (e.g. bcm5461x)
4) RGMII to external Gigabit Switch (e.g. bcm531x5)
5) RGMII ID mode disabled for external Gigabit Switch
6) RGMII to RGMII (e.g. STB<->3383)

Selection:1

Enter

reboot
 

seened

Registered
Messages
6
USB to RJ45 10/100 Mbps USB Ethernet Adapter
HTB1Qt7hJWSWBuNjSsrbq6y0mVXaa.jpg

CFE> ephycfg


Please select the board PHY design for eth0 interface
1) Internal 10/100Mbps PHY (build-in PHY)
2) MII to external 10/100Mbps PHY (e.g. bcm53101E)
3) RGMII ID mode disabled for external 10/100/1000Mbps PHY (e.g. bcm5461x)
4) RGMII to external Gigabit Switch (e.g. bcm531x5)
5) RGMII ID mode disabled for external Gigabit Switch
6) RGMII to RGMII (e.g. STB<->3383)


Selection: 2
 
Top