I

afmr

Registered
Messages
6
I have bought an new DM 520 and i have flashed the latest openatv file to DM 520. An error occoured but the button to reebot was active.

I have reeboted and ever since the box has the red light frozen and i can connect to it, not even true DCC.

Can anywhone help me please.

I am a rookie in this kind of subsjects.

Thank you
 

toysoft

Member
Messages
1,828
Connect to the mini USB port on the back with Putty, and 115200 bps as speed. If you have text going, this means the box is still alive, and posting what you see, could give a clue on how to fix.

TS
 

afmr

Registered
Messages
6
Connect to the mini USB port on the back with Putty, and 115200 bps as speed. If you have text going, this means the box is still alive, and posting what you see, could give a clue on how to fix.

TS

This is the text:

Dreambox DM520

M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@

BCM973625A0 CFE v15.3, Endian Mode: Little
Build Date: Fri Jun 24 16:38:03 2016 (Jann@Cynric)
Copyright (C) Broadcom Corporation.

card if inited
Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spar e Area Size=16
MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256

CPU speed: 751MHz
DDR Frequency: 1061 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 16MB
RTS VERSION: rts_hevc10_1067
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1

DM init finalization
yxml: processing file of 131072 bytes... succeeded!
no file loaded, create xml restoring default xml
loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1
[1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options
[2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options
[3] type 1, dev eth0, loader elf, filesys tftp, file , options bmem=192M@64M con sole=ttyS0,1000000 root=/dev/nfs ip=dhcp
added 3 sources to autoboot list
init fp
Initializing USB.

CFE initialized.
found card in unknown state
ca valid!



***** DREAMBOX SSBL *****

Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 5 00ms to cancel
Proceeding with autoboot.. You can try aborting with Ctrl+C

*** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf)

Ethernet Cable unplugged
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:
Loading: 0x80001000/7448768 0x8071b8c0/240128 Entry address is 0x805af9b0
Closing network eth0
Starting program at 0x805af9b0

[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.236000] loop: module loaded
[ 0.237000] brcmstb_nand: NAND controller driver is loaded
[ 0.238000] tun: Universal TUN/TAP device driver, 1.6
[ 0.239000] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 0.361000] bcmgenet: configuring instance #0 for internal PHY
[ 0.381000] bcmgenet bcmgenet.0: (unregistered net_device): link down
[ 0.382000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.383000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.383000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 0.415000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.421000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.422000] hub 1-0:1.0: USB hub found
[ 0.422000] hub 1-0:1.0: 2 ports detected
[ 0.423000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.424000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.424000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
[ 0.425000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
[ 0.491000] hub 2-0:1.0: USB hub found
[ 0.491000] hub 2-0:1.0: 2 ports detected
[ 0.492000] Initializing USB Mass Storage driver...
[ 0.493000] usbcore: registered new interface driver usb-storage
[ 0.494000] USB Mass Storage support registered.
[ 0.494000] i2c /dev entries driver
[ 0.495000] lirc_dev: IR Remote Control driver registered, major 253
[ 0.495000] usbcore: registered new interface driver btusb
[ 0.497000] TCP: cubic registered
[ 0.497000] NET: Registered protocol family 10
[ 0.499000] NET: Registered protocol family 17
[ 0.499000] Bluetooth: RFCOMM TTY layer initialized
[ 0.500000] Bluetooth: RFCOMM socket layer initialized
[ 0.501000] Bluetooth: RFCOMM ver 1.11
[ 0.501000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.502000] Bluetooth: BNEP filters: protocol multicast
[ 0.502000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.503000] L2TP core driver, V2.0
[ 0.503000] Registering the dns_resolver key type
[ 0.504000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.506000] EBI CS2: setting up NAND flash (primary)
[ 0.507000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 512MiB 3,3V 8-bit)
[ 0.508000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
[ 0.508000]
[ 0.510000] Bad block table found at page 262080, version 0x01
[ 0.511000] Bad block table found at page 262016, version 0x01
[ 0.512000] nand_read_bbt: bad block at 0x000002280000
[ 0.513000] nand_read_bbt: bad block at 0x000005fe0000
[ 0.513000] nand_read_bbt: bad block at 0x00000ec20000
[ 0.514000] nand_read_bbt: bad block at 0x000014d00000
[ 0.515000] nand_read_bbt: bad block at 0x000018da0000
[ 0.515000] nand_read_bbt: bad block at 0x00001c820000
[ 0.516000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.517000] 0x000000000000-0x00001f500000 : "rootfs"
[ 0.519000] 0x000000000000-0x000020000000 : "entire_device"
[ 0.521000] 0x00001f500000-0x00001fa00000 : "kernel"
[ 0.523000] EBI CS0: setting up SPI flash
[ 0.523000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
[ 0.524000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
[ 0.525000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
[ 0.526000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.528000] UBI: attaching mtd0 to ubi0
[ 0.528000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.529000] UBI: logical eraseblock size: 126976 bytes
[ 0.530000] UBI: smallest flash I/O unit: 2048
[ 0.530000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.531000] UBI: data offset: 4096
[ 3.675000] UBI: max. sequence number: 1535
[ 3.692000] UBI: attached mtd0 to ubi0
[ 3.692000] UBI: MTD device name: "rootfs"
[ 3.693000] UBI: MTD device size: 501 MiB
[ 3.693000] UBI: number of good PEBs: 4002
[ 3.694000] UBI: number of bad PEBs: 6
[ 3.694000] UBI: number of corrupted PEBs: 0
[ 3.695000] UBI: max. allowed volumes: 128
[ 3.695000] UBI: wear-leveling threshold: 4096
[ 3.696000] UBI: number of internal volumes: 1
[ 3.697000] UBI: number of user volumes: 1
[ 3.697000] UBI: available PEBs: 0
[ 3.698000] UBI: total number of reserved PEBs: 4002
[ 3.698000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 3.699000] UBI: max/mean erase counter: 3/1
[ 3.699000] UBI: image sequence number: 1129702877
[ 3.700000] UBI: background thread "ubi_bgt0d" started, PID 53
[ 3.702000] ALSA device list:
[ 3.702000] No soundcards found.

[ 3.753000] UBIFS: recovery needed
[ 3.812000] UBIFS: recovery completed
[ 3.813000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs"
[ 3.814000] UBIFS: file system size: 500666368 bytes (488932 KiB, 477 MiB, 3943 LEBs)
[ 3.815000] UBIFS: journal size: 25014272 bytes (24428 KiB, 23 MiB, 197 LEBs)
[ 3.816000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 3.816000] UBIFS: default compressor: lzo
[ 3.817000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 3.818000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 3.819000] devtmpfs: error mounting -2
[ 3.820000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 3.821000] Rebooting in 180 seconds..
 

toysoft

Member
Messages
1,828
I PM you where to post your log, where you could have help about how to fix hardware/software.

TS
 

majid3770

Registered
Messages
3
I have bought an new DM 520 and i have flashed the latest openatv file to DM 520. An error occoured but the button to reebot was active.

I have reeboted and box has the red light:(:(:(

Dreambox DM520

M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@

BCM973625A0 CFE v15.3, Endian Mode: Little
Build Date: Fri Jun 24 16:38:03 2016 (Jann@Cynric)
Copyright (C) Broadcom Corporation.

card if inited
Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spar
e Area Size=16
MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256

CPU speed: 751MHz
DDR Frequency: 1061 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 16MB
RTS VERSION: rts_hevc10_1067
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1

DM init finalization
yxml: processing file of 131072 bytes... succeeded!
no file loaded, create xml restoring default xml
loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1
[1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options
[2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options
[3] type 1, dev eth0, loader elf, filesys tftp, file , options bmem=192M@64M con
sole=ttyS0,1000000 root=/dev/nfs ip=dhcp
added 3 sources to autoboot list
init fp
Initializing USB.

CFE initialized.
found card in unknown state
ca valid!



***** DREAMBOX SSBL *****

Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 5
00ms to cancel
Proceeding with autoboot.. You can try aborting with Ctrl+C

*** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf)

Ethernet link is up: 100 Mbps Full-Duplex
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:
Loading: 0x80001000/7448768 0x8071b8c0/240128 Entry address is 0x805af9b0
Closing network eth0
Starting program at 0x805af9b0

[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.232000] console [ttyS0] enabled, bootconsole disabled
[ 0.236000] loop: module loaded
[ 0.237000] brcmstb_nand: NAND controller driver is loaded
[ 0.238000] tun: Universal TUN/TAP device driver, 1.6
[ 0.239000] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 0.361000] bcmgenet: configuring instance #0 for internal PHY
[ 0.381000] bcmgenet bcmgenet.0: (unregistered net_device): link down
[ 0.382000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.383000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.383000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus numbe
r 1
[ 0.415000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.421000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.422000] hub 1-0:1.0: USB hub found
[ 0.422000] hub 1-0:1.0: 2 ports detected
[ 0.423000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.424000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.424000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus numbe
r 2
[ 0.425000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
[ 0.491000] hub 2-0:1.0: USB hub found
[ 0.491000] hub 2-0:1.0: 2 ports detected
[ 0.492000] Initializing USB Mass Storage driver...
[ 0.493000] usbcore: registered new interface driver usb-storage
[ 0.494000] USB Mass Storage support registered.
[ 0.494000] i2c /dev entries driver
[ 0.495000] lirc_dev: IR Remote Control driver registered, major 253
[ 0.495000] usbcore: registered new interface driver btusb
[ 0.497000] TCP: cubic registered
[ 0.497000] NET: Registered protocol family 10
[ 0.499000] NET: Registered protocol family 17
[ 0.499000] Bluetooth: RFCOMM TTY layer initialized
[ 0.500000] Bluetooth: RFCOMM socket layer initialized
[ 0.501000] Bluetooth: RFCOMM ver 1.11
[ 0.501000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.502000] Bluetooth: BNEP filters: protocol multicast
[ 0.502000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.503000] L2TP core driver, V2.0
[ 0.503000] Registering the dns_resolver key type
[ 0.504000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.506000] EBI CS2: setting up NAND flash (primary)
[ 0.507000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 5
12MiB 3,3V 8-bit)
[ 0.508000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B
OOB, 8-bit, BCH-4
[ 0.508000]
[ 0.510000] Bad block table found at page 262080, version 0x01
[ 0.511000] Bad block table found at page 262016, version 0x01
[ 0.512000] nand_read_bbt: bad block at 0x000019ce0000
[ 0.513000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.514000] 0x000000000000-0x00001f500000 : "rootfs"
[ 0.516000] 0x000000000000-0x000020000000 : "entire_device"
[ 0.518000] 0x00001f500000-0x00001fa00000 : "kernel"
[ 0.520000] EBI CS0: setting up SPI flash
[ 0.520000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
[ 0.521000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated

[ 0.522000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
[ 0.523000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.525000] UBI: attaching mtd0 to ubi0
[ 0.525000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.526000] UBI: logical eraseblock size: 126976 bytes
[ 0.527000] UBI: smallest flash I/O unit: 2048
[ 0.527000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.528000] UBI: data offset: 4096
[ 3.680000] UBI: max. sequence number: 1397
[ 3.697000] UBI: attached mtd0 to ubi0
[ 3.697000] UBI: MTD device name: "rootfs"
[ 3.698000] UBI: MTD device size: 501 MiB
[ 3.698000] UBI: number of good PEBs: 4007
[ 3.699000] UBI: number of bad PEBs: 1
[ 3.699000] UBI: number of corrupted PEBs: 0
[ 3.700000] UBI: max. allowed volumes: 128
[ 3.700000] UBI: wear-leveling threshold: 4096
[ 3.701000] UBI: number of internal volumes: 1
[ 3.702000] UBI: number of user volumes: 1
[ 3.702000] UBI: available PEBs: 0
[ 3.703000] UBI: total number of reserved PEBs: 4007
[ 3.703000] UBI: number of PEBs reserved for bad PEB handling: 40
[ 3.704000] UBI: max/mean erase counter: 2/1
[ 3.704000] UBI: image sequence number: -2022897891
[ 3.705000] UBI: background thread "ubi_bgt0d" started, PID 53
[ 3.707000] ALSA device list:
[ 3.707000] No soundcards found.

[ 3.758000] UBIFS: recovery needed
[ 3.760000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
1051:71680, written 0 bytes
[ 3.761000] UBI warning: ubi_eba_write_leb: failed to write data to PEB 1051
[ 3.762000] UBI: recover PEB 1051, move data to PEB 2417
[ 3.763000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2417:2048, written 0 bytes
[ 3.764000] UBI warning: recover_peb: failed to write to PEB 2417
[ 3.765000] UBI: try again
[ 3.765000] UBI: run torture test for PEB 2417
[ 3.766000] UBI: recover PEB 1051, move data to PEB 2418
[ 3.767000] UBI error: do_sync_erase: cannot erase PEB 2417, error -5
[ 3.767000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2418:2048, written 0 bytes
[ 3.767000] UBI warning: recover_peb: failed to write to PEB 2418
[ 3.767000] UBI: try again
[ 3.767000] UBI: recover PEB 1051, move data to PEB 2419
[ 3.768000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2419:2048, written 0 bytes
[ 3.768000] UBI warning: recover_peb: failed to write to PEB 2419
[ 3.768000] UBI: try again
[ 3.768000] UBI: recover PEB 1051, move data to PEB 2420
[ 3.768000] UBI error: ubi_io_write: error -5 while writing 2048 bytes to PEB
2420:2048, written 0 bytes
[ 3.768000] UBI warning: recover_peb: failed to write to PEB 2420
[ 3.768000] UBI warning: ubi_ro_mode: switch to read-only mode
[ 3.768000] UBIFS error (pid 1): ubifs_leb_write: writing 2048 bytes to LEB 1
:67584 failed, error -5
[ 3.768000] UBIFS warning (pid 1): ubifs_ro_mode: switched to read-only mode,
error -5
[ 3.768000] Call Trace:
[ 3.768000] [<805b24e4>] dump_stack+0x8/0x34
[ 3.768000] [<8020ee3c>] ubifs_leb_write+0xc4/0xcc
[ 3.768000] [<802159c0>] ubifs_write_master+0xd8/0x138
[ 3.768000] [<8020d06c>] ubifs_mount+0xfbc/0x1580
[ 3.768000] [<800d3a7c>] mount_fs+0x20/0xe4
[ 3.768000] [<800f0258>] vfs_kern_mount+0x58/0xf4
[ 3.768000] [<800f0c7c>] do_kern_mount+0x4c/0x124
[ 3.768000] [<800f2b04>] do_mount+0x448/0x7b0
[ 3.768000] [<800f3154>] sys_mount+0x94/0xe4
[ 3.768000] [<806def0c>] mount_block_root+0x148/0x2a8
[ 3.768000] [<806df2c4>] prepare_namespace+0xfc/0x224
[ 3.768000] [<806dec14>] kernel_init+0x258/0x260
[ 3.768000] [<8000614c>] kernel_thread_helper+0x10/0x18
[ 3.768000]
[ 3.785000] UBI error: erase_worker: failed to erase PEB 2417, error -5
[ 3.786000] UBI: mark PEB 2417 as bad
[ 3.786000] UBI error: ubi_io_mark_bad: read-only mode
[ 3.787000] UBI error: do_work: work failed with error code -30
[ 3.787000] UBI error: ubi_thread: ubi_bgt0d: work failed with error code -30

[ 3.794000] VFS: Cannot open root device "ubi0:dreambox-rootfs" or unknown-bl
ock(31,0): error -5
[ 3.795000] Please append a correct "root=" boot option; here are the availab
le partitions:
[ 3.796000] 1f00 513024 mtdblock0 (driver?)
[ 3.796000] 1f01 524288 mtdblock1 (driver?)
[ 3.797000] 1f02 5120 mtdblock2 (driver?)
[ 3.797000] 1f03 16384 mtdblock3 (driver?)
[ 3.798000] 1f04 491412 mtdblock4 (driver?)
[ 3.799000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(31,0)
[ 3.800000] Rebooting in 180 seconds..
 

John-2k10

Registered
Messages
2
Since you still have access with the network and the rescue mode I advise you to use the front push button method.

So, you need to go to the rescue mode which can only be seen on the tv screen.
It's not so easy to reach, you must after switching on the box touch the button on the front.
Mostly you need to do several attempt to got there, you need seconds after turning on the box touch the button.
When it's reacts, you see it flashing, and afterwards you get the ip number or a http address on screen which you can use in your browser to access the box etc.

Upload a image file which is suitable for the sim card or sim card chip that has been placed in your box.
If you have a sim card sim 2.30 then use image files which are written for these cards search to dm520 sim 2.30 image files.

If you have a box, equipped with a A8P sim card or chip, then you can use the original image files as from OpenAtv.

Anyways, before you upload a image file it's better to look in the box to see which sim card it has before uploading a image file.
 
Top