- Añadida compatibilidad +SSSP con Mbox.
- Solucionado el problema de los philips con +SSSP en algunos canales Viaccess.
- Mayor estabilidad en los protocolos +SSSP
Seca3 smart card support
Soft 08.01 beta 01 do DSX6010
*DSX6010_08.01b2
DSX6010_08.02_SET.
- Opzione Auto protocollo, configurabile utilizzando i tasti +-B-4 del telecomando che, una volta impostata offre la possibilità di selezionare tra i tre protocoli dispnibili (MHWP, mbox, Gbox) e che si avvierà automaticamente alla successiva accensione del decoder.
- Possibilità di spegnere il decoder senza doverlo disconnettere da un protocollo.
- Trasferita la schermata delle informazioni sui parametri del canale dall'ubicazione +-B-4 alla sua nuova ubicazione +-B-6.
- Risolto il bug relativo alla corretta memorizzazione e visualizzazione dei nuovi canali aggiunti manualmente.
- Realizzati alcuni miglioramenti nel codice di programmazione interno ed nella visualizzazione di alcuni dati.
Questo firmware viene fornito senza flash512k e senza Eeprom in quanto per permetterne il suo miglior funzionamento è assolutamente necessario re-inizializzare il vostro decoder cancellandone e ricreandone la Eeprom interna tramite la procedura della minisintonia.
Questa operazione è strettamente necessaria anche se state già utilizzando una precedente versione di Jungle in quanto solo ricreandone i giusti parametri il vostro decoder potrà sfruttare appieno le opzioni disponibili in questa versione 8 del firmware.
DSX6010_08.03_SET
Zmiana sposobu szukania kluczy DW w rozkodowaym ECMie nagra2.
Multi-scan ordered SECA-ID, is able to sort up to 8 IDs at the same time,
the different platforms arranged by the supplier.
Occupy the channel list in the order created in the SECA ID
in the virtual card.
Checked-in time with the following ID is in SECAs Astra 19.2E:
SPAIN 4106
FRANCE 0081
HOLLAND 006A
soft is the software equivalent of 08.03 for 6010, not only sharing the rs (as easily as in 6010 can not be done).
So, summarizing:
- conax card support (including giving powers)
- support diseqc 1.0 (including support for diseqc standing near the primary and eeprom and excluding lnb power supply)
- patch clear
- manage blockers
- sending the slot on ecmów prov. Beef
- led indication (in normal operation it is recommended that you opt-out)
- record emmów to flash (6 is supported from the sectors 0xa0aa to 0xa0af, recalls that in 3010 they have a size of 0x10000)
- using an external module emu
- change in operation mode auto ecmpid
DSB3010_08.04 SET
New release jungle v10 by jungleteam
With :
codice:
Solution to 4 BUGs:
He who randomly changed in certain circumstances the "Self-System", "self-identity" and "Auto-Protocol" for values out of range.
- The block that prevented perso-2 channels
- The one we left the black screen until you restart the deco, after another satellite to scan and have not previously viewed channels were found.
- The sampling amending the last byte the VIACCESS ID.
Other News:
- The channel management, discontinue the column "Active" not be necessary. Marking group of channels (perso-2-serv), reports the detail of satellite groups and REDID transponder to make, which belong to the selected channel.
- Switching type settings separately for each antenna (the selection is eliminated general switching). Every moment we have the 32 selectable antennas, the sub-screen modification of the motor position is accessible only when we assign a position and thus define that uses antenna motor; Logically, if the engine parameters select Type "EmuMotor "does not show the access to modify the position defined.
- Adding a satellite channel, maintains the PID that we set earlier.
- Unified all transponder data "+, b, 5" to a single screen.
Dedica particolare:
Tratto da un post del prof.Ram
Corso di riparazione per alunni indisciplinati.
Grazie a questi alunni indisciplinati, Caro Prof Ram, Oggi è stato possibile realizzare questo nuovo firmware che il Team ANDRYSAT è orgoglioso di dedicarti con tutto il Cuore.
FW Sat *** v.1 per Philips DSX6071 e DSX6072
Realizzazione: ANDRYSAT Team
Grazie a: hubner, nonsacciunenti, ramas, celtic1, piterfree, ziganSky, MaXi, digital, marus, soave, Katrame, haron03, maildec, trani.
Inoltre un ringraziamento particolare va al nostro amico ideatore che ha scelto di rimanere fantasma.
Attenzione:
Questo firmware permette la visione dell'abbonamento Sky, soltanto inserendo nell’apposito slot LA CARD *** ATTIVA in vostro possesso. Per gli altri canali FTA non c'è bisogno di nessuna card inserita.
Il firmware non supporta nè contiene K.E.Y
NON MODIFICARE NE TOGLIERE QUESTE INFO:
Citazione:
· ANDRYSAT declina ogni responsabilità per l'utilizzo del FW per fini illegali come la visione di TV a pagamento o per le quali è previsto un regolare abbonamento.
· E' possibile pubblicarli su altri siti senza problemi, alla condizione che il file compresso venga pubblicato senza modifiche, lasciando intatto questo file leggimi.
Installazione:
Programmi da usare: Oslink V.4.00 (consigliato) oppure JTAG.
Caricare prima il firmware a FFFF, poi il firmware completo da 2 Mb scrivendo tutti i settori ed infine la eeprom allegata.
Nella prossima release che, al momento è allo studio, ci saranno ulteriori novità.
Features:
Menu languages: Dutch, English (Some French is implemented)
Seca2 smartcard support
Cardemulator support:
IRDETO1/BETACRYPT
NAGRAVISION2 (ROM120 MECM 60 and 61, AU)
VIACCESS 2.3
TPSCrypt --> REMOVED
CRYPTOWORKS
SECA1
SECA2 (nano 5105).
*** temp. fix PW