Tools For Vu+

Status
Not open for further replies.

elgeneral

Registered
Messages
7,811
HP USB Disk Storage Format Tool modified

Format Tool modified Boot Dos included

Gracias a stauffie
 

elgeneral

Registered
Messages
7,811
Vu+ Settings Backup Tool by Lee.

This util will make a backup of your Vu+ settings, Channel List, Satellites, Dish Positions, Radio Stations, Favourites, Timezone.

Unzip Instructions

Unzip all the files including the "enigma2" & "tuxbox" folders in this zip to your local HDD.
Be sure to tick the box "Use Folder Names" or "Extract Full Paths" depending on your Zip Utility.
File structure should look like this on your Hard Disk after unzipping.

enigma2 (folder)
tuxbox (folder)
Instructions.txt (this file)
Vu_Settings_backup.exe (Main Program)

If you don't see the "enigma2" & "tuxbox" folders then you've unzipped the files incorrectly and the application won't
function without them.

Instructions

To get the IP number of the Vu+ Press Menu on Vu+ Remote Control.
Select Setup and Press OK
Select System and Press OK
Select Network and Press OK
Select Network Test and Press OK

This will show the Vu+ IP Address, example 192.168.1.7

Program Instructions

1. Run the Vu_Settings_backup.exe program.
2. Enter the IP address of your Vu+ in the IP Address field
3. If you have changed the password on your receiver, enter the password in the password field otherwise leave blank.
4. Click Connect Button

Now click on BACKUP button.
This will backup all the settings files from the Vu+ to the /enigma2 and /tuxbox folders on your PC HDD.
The /enigma2 and /tuxbox folders are located in the same folder as this program.

To RESTORE your Vu+ settings after flashing a new Image simply do the following.

1. Run the Vu_Settings_backup.exe program.
2. Enter the IP address of your Vu+ in the IP Address field
3. If you have changed the password on your receiver, enter the password in the password field otherwise leave blank.
4. Click Connect Button

Now click on the RESTORE button.

All your backup data will be restored to the /etc/enigma2 and /etc/tuxbox folders on the Vu+
Once the files have successfully been restored you'll need to reboot the receiver by powering off and on using the switch on
the back of the receiver.
 

elgeneral

Registered
Messages
7,811
Vu+ Settings Backup Tool V1.2 by Lee

This util will make a backup of your Vu+ settings, Channel List, Satellites, Dish Positions, Radio Stations, Favourites, Timezone.

Unzip Instructions

Unzip all the files in this archive to your local HDD.

Instructions
------------------

To get the IP number of the Vu+ Press Menu on Vu+ Remote Control.
Select Setup and Press OK
Select System and Press OK
Select Network and Press OK
Select Network Test and Press OK

This will show the Vu+ IP Address, example 192.168.1.7

Program Instructions
---------------------------------

1. Run the Vu_Settings_backup.exe program.
2. Enter the IP address of your Vu+ in the IP Address field
3. If you have changed the password on your receiver, enter the password in the password field otherwise leave blank.
4. Click Connect Button

Now click on BACKUP button.
This will backup all the settings files from the Vu+ to the /enigma2 and /tuxbox folders on your PC HDD.
The /enigma2 and /tuxbox folders will be created in the same folder as this program.

To RESTORE your Vu+ settings after flashing a new Image simply do the following.

1. Run the Vu_Settings_backup.exe program.
2. Enter the IP address of your Vu+ in the IP Address field
3. If you have changed the password on your receiver, enter the password in the password field otherwise leave blank.
4. Click Connect Button

Now click on the RESTORE button.

All your backup data will be restored to the /etc/enigma2 and /etc/tuxbox folders on the Vu+
Once the files have successfully been restored you'll need to reboot the receiver by powering off and on using the switch on
the back of the receiver.

Version History
V1.2 Released 2 June 2010 |Application now creates enigma2 and tuxbox folders on the local HDD before backing up the settings.
V1.1 Released 20 May 2010 |Minor bug fixed.
V1.0 Released 19 May 2010
 

elgeneral

Registered
Messages
7,811
Vu+ Settings Backup Tool V1.3 by Lee

V1.3 Released 19 June 2010

Fixed problem backing up settings when an additional folder exists in 'enigma2' or 'tuxbox' folders
 

MIKAME

Super VIP
Messages
5,429
****************************************
** TooLVu+ Version 1.0 - TechSat TEAM**
****************************************




This program includes several tools for Vu+


Usage:
1) run program (toolVU.exe)
2) Choose the tool

tool included :

- DreamLogo Generator
- DreamBox Edit
- VuSettings Backup
- e2skinner
- Vu Util
- DreamMaker
- Putty
- Filezilla

note:This tool is portable, can be used from a USB stick


-------------
TechSat TEAM
-------------
 

elgeneral

Registered
Messages
7,811
Vu+ Duo DVB Module Updater by Lee - Goldwafers

Vu+ Duo DVB Module Updater by Lee - Goldwafers

New DVB Modules in "module" folder is Version mbox-dvb-modules-bm750-2.6.18-7.3-4.1.1-20100827
Old DVB Modules in "backup" folder is Version mbox-dvb-modules-bm750-2.6.18-7.3-20100611

WARNING READ THIS VERY CAREFULLY:
I recommend backing up your original DVB modules first before uploading new ones.
Older Images like Dream Elite BH 1.3.3F won't work with the latest DVB Modules.
Dream Elite BH 1.3.3F will only work with mbox-dvb-modules-bm750-2.6.18-7.3-20100611 or below.

If your receiver doesn't boot after upgrading don't worry just use the Restore Original DVB Modules option.

The backup folder contains the mbox-dvb-modules-bm750-2.6.18-7.3-20100611 modules by default.

Unzip Instructions
---------------------------

Unzip all the files and folders in this archive to your local HDD.

Instructions
------------------

Enter the receiver IP address in the IP Address field.
Username: root
Password:

There is no default password so leave this field blank unless you have changed the password in which case enter your password.

Click the Connect Button.

I recommend backing up your original DVB modules first before uploading new ones.

Click the Backup Original DVB Modules Button.

Wait until the “Successfully backed up original modules to backup folder.” Message appears.

Click the Upload New DVB Modules Button.

Wait until the “Successfully uploaded new modules to Vu+ Duo, Now Reboot Receiver.” Message appears.

Now close the program and reboot your receiver.

Please note it can take approx 3 minutes for the receiver to boot up after a reboot so be patient.

If you should experience any problems after updating DVB Modules then you can always revert back to the original DVB Modules from the backup you made at the start.

To restore original DVB Modules:

Click the Restore Original DVB Modules Button.

Wait until the “Successfully restored backup modules to Vu+ Duo, Now Reboot Receiver.” Message appears.

Now close the program and reboot your receiver.

Please note it can take approx 3 minutes for the receiver to boot up after a reboot so be patient.


Keeping DVB Drivers up to date:

Download the latest drivers from

http://archive.vuplus.com/download/drivers/

Use Winrar to unrar the latest mbox-dvb-modules-bm750-2.6.18-7.3-4.1.1 files to the “modules” folder. The “modules” folder is located in the same folder as the Vu+ Duo DVB Module Updater application.


Trouble Shooting:
Q. I can't connect to the receiver.
A. Check you have entered the IP Address correctly.
Check Firewall isn't blocking the application. The application requires Network access to backup &
upload the DVB Module files.

Q. Receiver wont boot after updating to the latest DVB Modules.
A. Older images like Dream Elite BH 1.3.3F will only work with mbox-dvb-modules-bm750-2.6.18-7.3-20100611 or below.
If your receiver doesn't boot after upgrading don't worry just use the Restore Original DVB Modules option.

Regards

Lee.
Goldwafers
 

hilton

Registered
Messages
7,622
Vu+ Duo_Solo Toolbox Ver. 3.1

NEWS:Ver. 3.1

07-10-10

- add sound
- add new Tools and FAQs
- Removed old Tools
- Small bugs fixed

-----------------------------

Vu+ Duo Solo Toolbox Ver. 2.0
08-08-10
- more Tools & FAQs
- Style fixed
- Small bugs fixed.

Code:
http://rapidshare.com/#!download|953l32|446299219|Vu__Duo_Solo_Toolbox_Ver._3.1.rar|39758
 

joedenob

Registered
Messages
319
Sat4Fun Vu+ MultiTool

Sat4Fun Vu+ MultiTool
29.10.2010



This MultiTool has:


Vu+ Util

Vu+ CC

Vu+ Settings Backup Tool

DreamBoxEdit 3.0.0.0

Dream Logo Generator

e2skinner

Picon Creator

Dreamset

FAT32 for USB Pens

Vu+ Duo DVB Module Updater

Vu+ Solo DVB Module Updater



DOWNLOAD
 

aguda

Registered
Messages
2,879
VuUtil for MacOSX - BETA Version

schermata20101124a13443.png
MaxOSX Porting
- Wine 1.3.7


Program:
Utilities and usages for upgrading your box

You have two choices to upgrade firmware of your vu+ box.
One is using MAC program and the other is using USB memory stick.
You can freely choose upgrade method at your convenience.

Using MAC

* MAC program
* Usages


Credit:
Bobsilvio


schermata20101124a13304.png
schermata20101124a13310.png
schermata20101124a13314.png

 

elgeneral

Registered
Messages
7,811
VU+ Easy Load Tools for CCcam-Exchange


cccamscreen.jpg



The first ever release of VU+ Easy Load Tools created by

This release includes the following software, tool and utils in one easy to run portable file:

VU+ Settings Backup Tool
VU+ SOLO DVB Module Updater
VU+ DUO DVB Module Updater
VuUtil
VU+ Control Centre
USB Format Tool
DreamBoxEdit
Dream Logo Generator
E2 Skinner
PuTTY
WinSCP

Download VU Easy Load Tools Version 1.0 CCcam-Exchange
 
Last edited by a moderator:

elgeneral

Registered
Messages
7,811
ZebraDem-Feedbox for Vuplus

Available Future
:
- Skin
- Boot Logo
- Spinner
- Plugin

Available functions:
- under "?" FAQ at Skincrash with Green Screen
- *. ipk copy from the PC to the box and install
- pictures / info download the skins / plugin / Spinner / boot logo of feed in the tool server and show
- *. ipk copy from the server to feed the box and install
- uninstall Skin & Plugins
- look for converging packages (via a search term), can uninstall list &

ZebraDem and a spinner as well as boat logo are also available

Coll are only a few feed entries, will change but more on that here _

Talk about problems, bugs, or requests for changes, then it goes here weiter_

A big thank you for the test goes to:

gladiator-01, Einstein67, malau


gracias a tuete2501
 

marce

VIP
Messages
7,115
ZebraDem-Feedbox-VUplus v.1.1

feedbox11.jpg



Code:
So, now the new version with some quite

The following was changed:

Features Available:
- Picon

Available functions:
- FAQ -> Prepare for USB Picon
- Query Enigma2 restart "after the installation of Packet
Thx tuete2501
 

elgeneral

Registered
Messages
7,811
ZD-Feedbox-Setup-v1.2.0


Features:
- Skin
- Bootlogo
- Spinner
- Plugin
- Picon (ZD-Feedbox-v1.1.0)
- Radiologo (ZD-Feedbox-v1.2.0)

gracias a tuete2501
 

marce

VIP
Messages
7,115
ZD-Feedbox-Setup-v1.2.1


Code:
Available functions:

- for Picon
- Installation & Moutmanager
Thx tuete2501
 

marce

VIP
Messages
7,115
ZD-Feedbox-Setup-v1.2.2

Code:
Available functions:

- for Picon
- Installation & Moutmanager
--- Mount Manager adjusted
 
Status
Not open for further replies.
Top