CCCam issues after IPTV.sh

Zoeper

Registered
Messages
8
Hi gals and guys!

Beginning of July I tried this Read Forum Rules Payserver discussions are Not permitted !! on my DM800se.
I wanted to see the quality of IPTV, and they weren’t great.
I have a wired connection to a Fiber line and hardly ever have issues streaming others, this was just terrible.

So I wanted to revert back to my CLine I have at digame.
They confirm the line is active, but neither on OSCAM nor on CCCam O have picture on non FTA channels.

Anyone an idea what I should do?

I already removed the iptv.sh from the box, I’ve checked CRON jobs, nothing there, and my official cards as well as FTA is working as it should.
Just the Clines don’t work. I can access the box via FTP too.

I wonder if it is an outgoing/incoming connection issue?
 

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,480
I could be a coincidence your CCcam is playing up after you installed IPTV. It could be a connection issue . What is CCcam info telling you ?

I guess the best way to solve this is flash a fresh image with your CCcam setup again and go from there.
 

Zoeper

Registered
Messages
8
Thank you for the reply!

And I already tried that, of course ;). I reset it to “Factory Setting” did a “Factory Reset”, and then, a day later, I flashed it with my known OpenPli Enigma2.

Is there a way to flush everything, so that it does not remember a thing from previous settings? I think that is causing the issue, as it does not remove certain settings/tools/programs after flashing.

Is there another image that I could/should use, as OpenPli is no longer supporting the DM800?
 

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,480
Factory reset is no good really and the only way to do a full flush as you put it is to reflash the image and start from scratch.
 

Zoeper

Registered
Messages
8
The update I did was no good, or so it seems.
How do I do such a „Full Flush“?

What I did was:
1 Power plug out
2 Press On and hold
3 Power plug in
4 Hold power button and wait for it to say STOP
5 Go to IP address and upload a new image

What should I additionally do?
BTW any image better than OpenPli Enigma2?
 

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,480
I finally found an error message: "nc : can't connect to remote host (127.0.0.1)".

Thats a standard loopback address so it carnt connect on your network was you trying to reach the CCcam web info page ?

If you were you need to use the IP for the receiver
 

Zoeper

Registered
Messages
8
Where should I setup that in CCCam?

I was just checking the CCCam information on the box (via the remote control).

I also installed OSCAM just now, and for the CLINES it just says "ERROR"?

Is there anywhere where I can change these loopback address setting on the box (via FTP). Wouldn't know where to start via Telnet.
 

Zoeper

Registered
Messages
8
Put this in your browser but with your boes IP address

http://192.168.0.?.:16001

That gives me an interesting view.
Now with channels that used to come in through the CLINE (e.g. 123.45.67.89:12345) it says /dev/sci0/ (it is trying to use the card).
The link also only works for CCCam 2.3.0 (and above?).

I can only download CCCam 2.0.9, CCCam 2.2.1 and CCCam 2.3.0 for OpenPli4

//edit
Found the CCCam 2.2.1 port (12000) but it does not load ATM. I am looking at the config to see if something is blocking it?
 
Last edited:

Ferret

Marching On Together !
Staff member
Administrator
Messages
17,480
16001 is the port number to reach CCcam the configs for the other CCcams could be using a different port.
 

Zoeper

Registered
Messages
8
16001 is the port number to reach CCcam the configs for the other CCcams could be using a different port.

Now it isn't reacting to anything at either port...

I am going to remove one of the two cccam...

No more response at 16001...

I am gonna toss this stupid DM800se out of the window... after I've removed the hard drive...
 

Zoeper

Registered
Messages
8
So I've tried switching to OScam and same issue.
Each [reader] is shown with status:"ERROR"

I am adding the content of my OSCAM config and server files for reference...

--== oscam.config ==--
[global]
disablelog = 1
logfile = /dev/tty
preferlocalcards = 1
disablecrccws_only_for = 0500:032830,030B00;1811:003311,003315;1819:00006D;098C:000000;09C4:000000;098D:000000;0500:050F00

[cache]

[cs378x]
port = 12005

[dvbapi]
enabled = 1
au = 1
pmt_mode = 6
user = dvbapiau
boxtype = dreambox

[webif]
httpport = 8081
httpallowed = 10.0.0.0-10.255.255.255,172.16.0.0-172.31.255.255,192.168.0.0-192.168.255.255,127.0.0.1

======================

--== oscam.server ==--
[reader]
label = ORF-card
description = ORF-card
protocol = internal
device = /dev/sci0
detect = cd
mhz = 450
cardmhz = 2700
group = 1
emmcache = 1,3,15,0
ratelimitecm = 4
ecmunique = 1
ratelimittime = 10000
srvidholdtime = 2000
cooldown = 30,600

[reader]
label = upper_card
protocol = internal
device = /dev/sci1
detect = cd
cardmhz = 2700
group = 1
emmcache = 1,3,15,0
ratelimitecm = 4
ecmunique = 1
ratelimittime = 10000
srvidholdtime = 2000
cooldown = 30,600

[reader]
label = Mainreceiver
enable = 0
protocol = cs378x
device = ip_adress_mainreceiver,12005
user = 2nd_box
password = 2nd_box
group = 1

[reader]
label = Cline
enable = 1
protocol = cccam
device = xxx.xxx.xxx.xxx,xxxxx
user = UserName
password = UserPassword
group = 1
cccversion = 2.3.0
cccmaxhops = 2
ccckeepalive = 1
audisabled = 1

======================

Looking at VU+, but from what I've read the issues could be the same there...
 
Top