Software for Opticum 4100tscx

bidja

Registered
Messages
12
Hi Everybody
I am quite new in this and I need some help about this receiver.
I have Opticum 4100tscx(chip 5119) and would like to know which software i can load in it. Also would like to know is it possible to watch any channels in USA with this receiver (i am working on ship and very soon I will go there).
Thanks
 

dreamer1983

Super VIP
Messages
4,878
Hi Everybody
I am quite new in this and I need some help about this receiver.
I have Opticum 4100tscx(chip 5119) and would like to know which software i can load in it. Also would like to know is it possible to watch any channels in USA with this receiver (i am working on ship and very soon I will go there).
Thanks

Here have you all the last firmware for truman version & check in key wich channal can you watch by opticum keys by dreamer1983
http://www.sat-universe.com/showpost.php?p=593673&postcount=13
 

bidja

Registered
Messages
12
Thanks for Your answer, but I made mistake. My receiver is opticum 4100 tscxe. Which SW I have to download?
Thanks
 

altero

Registered
Messages
6
firmware and software for opticum 4100tscx

hi there,
i've got this combo receiver, which i would use for DVB-T networks. i've seen there's different firmware available.which one should i use?as i'm not much into upgrading:confused:, is there any step by step guide i might follow?
thanks in advance
:)
 

wolf5

Registered
Messages
69
For Opticum CR/CX, TS, TS(CR,CX), Yumatu Saphire, Megasat 2000 CX(Combo),............. Receiver with 5119


you need:

-RS232 null modem cable

-Tools: AVChannelEdit_3.1.05 and AVUpgrade 3.1.07 (2 MB ver)

-Firmeware: truman_5119_house_emu_2.4.73_all_By dreamer1983

-:D act. Ke*file

>connect PC to receiver via rs232 cabel <

First you save your settings list AVChannelEdit_3.1.05.

1)Receiver no voltage and start AVchanneledit
****> IRD****> upload from Receiver****> Upgrade Data****> OK****> give name****> save****> receiver on
The fuse is!
If the receiver displays 1203 and then restarts it's done!


2)Receiver no voltage and start AVUpgrade 3.1.07.
****>open****>truman_5119_house_emu_2.4.73_all_By dreamer1983.dld****>start****>receiver on
In few minutes the receiver display 1203 and then restarts it´s done!



3)Receiver no voltage and start AVUpgrade 3.1.07.
****>open****>your setting list****>start****>receiver on
In few secondes the receiver display 1203 and then restarts it´s done!




4)Receiver no voltage and start AVUpgrade 3.1.07.
****>open****>act. Ke*file****>start****>receiver on
In few secondes the receiver display 1203 and then restarts it´s done!


Ready :clapping:
 
Last edited:

altero

Registered
Messages
6
act.Ke*file

thank you so much for your answer and hints to my post. i've found most of the files you suggested, and i just still need to buy the cable.
only wonder that exacty is act.Ke*file :confused: and where i might search for it.
sorry but i'm just a beginner.
thanks again
 

altero

Registered
Messages
6
great!:thum:
sounds like i just still need the cable...
thanks alot for the support
:clapping:
 

altero

Registered
Messages
6
everything done.
i wonder if i need any con*x card emulating software as my slot is empty...
i'm using my opticum 4100tscx only as a dvb-t receiver.
every suggestion would be highly welcome
;)
thanks
 

wolf5

Registered
Messages
69
only as a dvb-t? terr.

dvb-s as you have to use it already;) sat

e.g. Astra 19.2 and Hotbird 13 degrees

no card required
 
Top