How to reach to KEY MENU or KEY TABLE??

M

mehdi3

Registered
Messages
155
Hi everyone

I have loaded the latest S/W to my Receiver FERGUSON AF-7018UCI but i dont know how to reach to KEY TABLE to Edit some new key like SECA,CYPTOWORKS,NAGRA2 and etc...

Thanks in Advance
 
M

mehdi3

Registered
Messages
155
I have AF7,but it think its better to load keys by softcam as all keys should be updated.

Where can i find KEY LOADER(KEY UPGRADE)and latest softcam for my receiver AF-7018UCI??

Thanks again
 
F

FanOfSat

Registered
Messages
710
Would bet AF7 on DSR 7001, if this is it, push the red button so the DVBXTREME Menu will open and show you the way.
Consider, i don't know what you want to edit. (Austriasat is down!)
 
M

mehdi3

Registered
Messages
155
I want to get Sky link 23.5
Sky Link 23.5E ] | Cryptoworks |Provider: 0D03 | Astra 23,5°E |
0D03 0004 00 00xxxxxxxxxxxxxxxxxxxxxxx
0D03 0004 06 27xxxxxxxxxxx
0D03 0008 01 00xxxxxxxxxxxxxxxxxxxxxxx
0D03 0008 06 27xxxxxxxxxxxx


No keys in chat section!
 
F

FanOfSat

Registered
Messages
710
OK, sorry for my prejudice.
If this not work with edit per RC, maybe it works with a new keyfile.
 
M

mehdi3

Registered
Messages
155
Yes im looking for key file or softcam to send it by key loader(key upgrade)
but its look like nobody knows about that on here??
 
O

Ord Mantel

Registered
Messages
2,707
You have in upload section key Keys RC8.... Sending with A07 Key Sender.
Or manualy; Press Red button - Cryptoworks table...
 
M

mehdi3

Registered
Messages
155
I have downloaded the latest software to my receiver Ferguson AF-7018UCI and now Im trying to reach to KEY TABLE by pressing red button but I can only see this menu DVBXTREME SUBTITLES TUNER RESTART and there is no any KEY TABLE.

Could you please help me with this maybe I need a different Firmware??

Please send the link so i can download to the receiver??

Kind regards
 
F

FanOfSat

Registered
Messages
710
Press Menü, then blind "19370" should open a small window. Press 2486 and the Emu is switched on (activated).

To switch off the Emu set HCAS Mode: OFF

Seems that SkyLink is not possible with this software, couldn't find a way to insert cardsystem key.

But Austriasat works with this software.;)
 
M

mehdi3

Registered
Messages
155
I have been trying to add or edit new keys for SKY LINK Astra 23.5 all day today but I didn't have any success.
I think,there is something wrong with KEY TABLE as I can NOT find even old KEY or Provider for CZECH LINK to edit them and save it.
This needs to be done by engineer and all KEYS needs to be updated.
 
M

mehdi3

Registered
Messages
155
Thanks for the NEW S/W,but you didn't send the key loader and could you please explain how to send that KEY FILE(IRK)??

Thanks in Advance
 
F

FanOfSat

Registered
Messages
710
Would it be possible to do the same change for software AF7 RC7 6018 (DSR7000)?
Complete software open with a hexeditor?

For sending a keyfile exists already some loaders, "gasoline" is my favorit for this.
 
M

mehdi3

Registered
Messages
155
Hi Makaroff

I have tested that key file which you updated by you but it didn't open those Astra3 Channels,I saw the key table and all key has been updated nicely and correctly.
Its look like something is not ACTIVE to UNLOCK those Channels.
I hope you can resolve this issue soon.

Regards
 
M

mehdi3

Registered
Messages
155
Sky Link 23.5E ] | Cryptoworks |Provider: 0D03 | Astra 23,5°E

0D03 0004 00 00xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

0D03 0004 06 27xxxxxxxx

0D03 0008 01 00xxxxxxxxxxxxxxxxxxxxxxxxxxx

0D03 0008 06 27xxxxxxxxxx


No keys outside key section
 
O

Ord Mantel

Registered
Messages
2,707
@makaroff
In your SW is no SkyLink RSA key.

@FanOfSat
With HexEditor you can open all SW and reediting. Best program for key sending is A07 Key Sender.

@mehdi3
Read my replay to makaroff.
 
You must log in or register to reply here.
Top