How to for Sammy DSR 9500 VIA CI with Revolution Gold Emu 4.x by MAHDI!
- Thread starter gorski
- Start date
How To Flash Your Sammy And Get The Au To Work!!!
HOW TO FLASH YOUR SAMMY PROPERLY AND GET THE AU TO DO ITS MAGIC!!! :clapping::thum:
[Remember: switch your Sammy off at the back BEFORE and AFTER you program the EMU in! Do not hurry, do not cut corners, if you want it all to work properly!]
After Sammy has cooled down a bit [say 5 - 10 minutes] switch it on at the back and keep it on Standby.
Now start the STUDIO 1.2 [or 1.3] by MAHDI and go to DSR FW Loader and Send FW, then choose the Emu you want to put in [in this case the excellent 5.9!] and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush!
When you start Sammy via a remote go to RESET EMU [again: via a remote] by pressing 0 + Menu quickly in succession, then go down to RESET TO EMU DEFAULTS and press the OK button on your remote.
(After it resets you can go back to EMU MENU to make sure you have the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!])
Put Sammy to Standby and then kill at the back for a few minutes.
Restart your Sammy at the back, then leave it on Standby.
Now put the RAM in [Cruiser's are excellent!], if you need to, then start Sammy via remote.
==================================================
Now the AU function for D+, Premiere and TPS
Go to a channel in D+, for instance [I just did it on Taquila 7], then do the following...
[By the way, sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!]
Go to EMU Menu, where you should have:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]
Now do the EMU RESET, as described above, by pressing 0 + Menu quickly in succession, then go to RESET TO EMU DEFAULTS and OK.
Wait a little bit - it's fast to AU on all 3 providers!
Once you have the pretty colours go to the next of the 3 big publicly hacked providers [a channel of your choice]. Put your Sammy to Standby, then re-start it. Repeat the EMU Menu Reset to AU.
It should AU, provided you scanned the transponder on which you wanna AU.
Just flashed the receiver with 5.9 and tested:
TPS AU works fast! AU on FRANCE 4 [or any channel on that transponder]. Works great, no problems with flickering and freezing!
D+, too!
Premiere also!
Showtime and Pehla tested by anyone? The reports are that, at the moment, they are not working AU...
Enjoy [you lazy sods, who can't be bothered to read a bit, too...]!!:thum::clapping:
HOW TO FLASH YOUR SAMMY PROPERLY AND GET THE AU TO DO ITS MAGIC!!! :clapping::thum:
[Remember: switch your Sammy off at the back BEFORE and AFTER you program the EMU in! Do not hurry, do not cut corners, if you want it all to work properly!]
After Sammy has cooled down a bit [say 5 - 10 minutes] switch it on at the back and keep it on Standby.
Now start the STUDIO 1.2 [or 1.3] by MAHDI and go to DSR FW Loader and Send FW, then choose the Emu you want to put in [in this case the excellent 5.9!] and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush!
When you start Sammy via a remote go to RESET EMU [again: via a remote] by pressing 0 + Menu quickly in succession, then go down to RESET TO EMU DEFAULTS and press the OK button on your remote.
(After it resets you can go back to EMU MENU to make sure you have the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!])
Put Sammy to Standby and then kill at the back for a few minutes.
Restart your Sammy at the back, then leave it on Standby.
Now put the RAM in [Cruiser's are excellent!], if you need to, then start Sammy via remote.
==================================================
Now the AU function for D+, Premiere and TPS
Go to a channel in D+, for instance [I just did it on Taquila 7], then do the following...
[By the way, sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!]
Go to EMU Menu, where you should have:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]
Now do the EMU RESET, as described above, by pressing 0 + Menu quickly in succession, then go to RESET TO EMU DEFAULTS and OK.
Wait a little bit - it's fast to AU on all 3 providers!
Once you have the pretty colours go to the next of the 3 big publicly hacked providers [a channel of your choice]. Put your Sammy to Standby, then re-start it. Repeat the EMU Menu Reset to AU.
It should AU, provided you scanned the transponder on which you wanna AU.
Just flashed the receiver with 5.9 and tested:
TPS AU works fast! AU on FRANCE 4 [or any channel on that transponder]. Works great, no problems with flickering and freezing!
D+, too!
Premiere also!
Showtime and Pehla tested by anyone? The reports are that, at the moment, they are not working AU...
Enjoy [you lazy sods, who can't be bothered to read a bit, too...]!!:thum::clapping:
In addition:
do NOT reset the EMU every time you want a provider to AU!!!
Do it just once, after the installation!
Then put the RAM.bin in...
Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...
Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!
There, my good deed for the day is done...:clapping::thum:
do NOT reset the EMU every time you want a provider to AU!!!
Do it just once, after the installation!
Then put the RAM.bin in...
Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...
Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!
There, my good deed for the day is done...:clapping::thum:
mohsendust
Registered
- Messages
- 1
what is the new firmware now?
i am beginner. can you help me?
i am beginner. can you help me?
- Messages
- 6,174
Latest firmware is with highest number here:
http://www.sat-universe.com/forumdisplay.php?f=44
atm 5.9 as plyma mentioned.
Now it's much easier, as you know, guys.
Download the EMU v. 5.8 and unpack. Then replace 5.8 with 5.9 BIN EMU file.
As you start the Sammy's Share SW - it'll automatically start the GBox and it's a breeze... :thum:
Wrooom, wrooom... On we go!!!!!!!! :clapping: What an excellent piece of work this is!!!!!!!!!!!!!!!! BRAVO MAHDI!!!!!!!!!!!!!:thum:
Download the EMU v. 5.8 and unpack. Then replace 5.8 with 5.9 BIN EMU file.
As you start the Sammy's Share SW - it'll automatically start the GBox and it's a breeze... :thum:
Wrooom, wrooom... On we go!!!!!!!! :clapping:
What an excellent piece of work this is!!!!!!!!!!!!!!!! BRAVO MAHDI!!!!!!!!!!!!!:thum:If you have problems maybe uploading the new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well, kill your Sammy at the back and then... Here's a copy of my post from other threads:
keshamonas
Registered
- Messages
- 1
D+ down ???
Hi, I don`t normally work on Samsung but I have done it to some friends and worked out well.
Now I have one different from the others and is not communicating with Semco Editor. First I am trying to read the channel list and it is giving me Unknown Database received! (Database ver:20010405). So I am still afraid to send the Firm (EMU) before I be sure.
This Samsung is 9500 via ci. It has no switch at the back and the the
System info is
Loader version 101
Software version 133
Hardware version 104
I wonder if someone could be of some help please.
This seems like it had never been upgraded with any version
Does this one take the Emu 7.3?
Will it upgrade the system version with the Emu or there is some thing else?
Thanks
Now I have one different from the others and is not communicating with Semco Editor. First I am trying to read the channel list and it is giving me Unknown Database received! (Database ver:20010405). So I am still afraid to send the Firm (EMU) before I be sure.
This Samsung is 9500 via ci. It has no switch at the back and the the
System info is
Loader version 101
Software version 133
Hardware version 104
I wonder if someone could be of some help please.
This seems like it had never been upgraded with any version
Does this one take the Emu 7.3?
Will it upgrade the system version with the Emu or there is some thing else?
Thanks
No this version is
Loader version 101
Software version 133
Hardware version 104
That is why I am puzzled.
ThX
Summing up...........
0) One must have Loader 500 or 501 in one's machine [See your basic Settings in the Menu to check it], in order to programme it via a serial 9-pin cable.
If it doesn't work, one must use JTAG to put the Loader 500/501 in, then do the Emu via the serial cable.
Do not hurry, do not cut corners, if you want it all to work properly!
1) Connect Sammy with your PC/laptop
-for an older PC one needs only a serial cable, as chances are it has the serial [9 pin] port
-for a newer PC, if it has no serial but only a USB port, first connect your straight serial 9-pin cable into Sammy, plugging the other end of the cable into a "serial/USB" cable adaptor, so one can plug the other end of the adaptor into the USB port of your PC/laptop
2) Download the following, freshest files to your PC/laptop:
-EMU [the latest Emu is v. 8.4.]
-Tools
-Settings list
-RAM.bin
Unpack them to your PC/lappy, to their respective folders.
The programming itself
3) Switch off the receiver at the back, for 10-20 seconds, then turn it back on again.
4) Start STUDIO 1.5.1 by Maestro MAHDI (choose the right port, for instance COM1 or USB1 or whatever it is in your setup)
-click on DSR FW Loader, then
-Send FW, then
-choose the Emu you want to programme (the latest now is SamsungDSR9500_RVGOLD_V8.4) and then
-Open -> to programme the EMU.
One will see the progress on the LED or maybe on the TV screen, if one is connected to the TV.
WAIT for the CLOCK on Sammy display - do NOT hurry!!!
When it's finished, put the channels list in, using, for instance, Semco Editor.
Btw, SetEdit 1.12 exists, too. It does the job, too!
Receiver must be in Standby mode (using your remote control).
5) Start the Semco Editor (the right port should be chosen, for instance COM1 or USB1), then
-go to File in the upper left corner, then
-to Open
-a new window will appear, to choose a list on your PC (format "something.sdb"), then
-click on Open
-when Semco Editor opens it, click on the Load Data Base From PC To Set Top Box icon.
Wait.
When it is done, quickly do the Emu reset [one must be connected to the TV to see the options], which one does only once now, after programming the Emu:
6) Start Sammy from Standby using your remote and execute RESET OF EMU:
-press 0 + Menu on your remote, quickly, one after the other, then
-choose RESET TO EMU DEFAULTS and
-press OK on your remote.
Sammy should switch itself off now. Start Sammy from Standby using the remote.
{After it resets, you can go back to EMU MENU to make sure you have the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD
...or simply play with whatever Sammy has in RG 8.4 }
[Oh, by the way: sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!]
Now, let's put RAM.bin in [it contains the keys to open the hacked channels...]
7) Sammy is in Standby mode
-Start Samsung DSR Studio 1.5.1 -> choose Ram Editor modus (a special TAB).
-Click on Open File and find the latest RAM.bin on your PC/laptop
-If "Empty Write" is ticked/chosen - remove it.
-Click on Write and wait for "End Write"
Startaj Sammy and watch...
============BY THE WAY+++++++++++++
How to put the keys via remote in
Go to a coded channel and press 0, then Menu [as above] to open the EMU Menu.
At the bottom of the list you'll see Key Editor Menu -> choose a coding system -> Ident -> key one wants to edit.
The scheme is as follows:
0 = 0 Button
1 = 1 Button
2 = 2 Button
3 = 3 Button
4 = 4 Button
5 = 5 Button
6 = 6 Button
7 = 7 Button
8 = 8 Button
9 = 9 Button
A = PG+ Button
B = PG- Button
C = GREEN Button
D = YELLOW Button
E = BLUE Button
F = RED Button
Del = LAST Button
An example (thanx to Dalen)
=====================================
Newer EMU Gold 4.3 has more places/digits to put in.
The procedure is the same, except that one needs to press the EXIT button when finished:
410100xxxxxxxxxxxxxxxx -> EXIT takes you automatically back, having written the key in and the again
410101xxxxxxxxxxxxxxxx -> EXIT and that's it!
===========================================
Thanx to Cruiser:
Thanx to Maumixio, how to enter a DCW:
===========================================
Thanx to Cruiser for the list of channels which can be seen using Sammy's Emu and RAM.bin file/keys:
N*gra:
DigiTV 1°W ok key 00-17.06.09.
Tv Globo 13°E ok
Multicanal 30°W
Seca:
RAI 13°E- ok next key 0D July
Mediatech 4°W- ok next key 0D July
Cryptoworks:
Kingston 5°E
Jetix 13° 10723/H/29900
Cartoon Network & TNT Germany ok 9°E 11728/V/27500
Viaccess:
Mezzo 13°E 12245/H/27500
SIC Int. 16°E 12568/H/3703
MCM Belgique 5°W 12543/H/27500
Biss Channel:
12149 TVE 1 30°W;
11931 LDTV 30°W;
12149 TVM 2 30°W;
12092 AXN PORTUGAL 30°W;
11474 TV CANARIA 30°W;
12735 ENTV 15°W;
11177 FOX TV 12,5°W;
11373 TOUCH TV 12,5°W;
11188 FOX GERMANY 12,5°W;
11066 Fox Sport 8°W; new PMT
11066 Discovery 8°W;
11066 Fox news 8°W;
12583 2M 12,5°W;
11423 AL RIYADIAH 7°W;
11065 Canal 6 Feed 5°W
11065 ENTV 5°W
12543 FOX LIFE 5°W;
10722 MEGASPORT 4°W;
10722 TV KYIV 4°W;
10722 1PLUS1 4°W;
10759 Qtv 4°W;
11766 TET 5°E;
12073 OCK 5°E;
11823 S2K (Sat 2000) 9°E;
11296 S2K (Sat 2000) 13°E;
12673 TVM MAROC 13°E;
11643 MBC US 26°E;
12608 IMED 42°E;
11894 Ans TV 42°E
11178 Ekin Turk TV (USUK TV) 42°E;
12678 24 42°E;
12593 RUSTAVI 2 42°E;
11054 NTV SPOR 42°E;
11607 AZERBAYCAN TV 42°E;
11870 TV8 42°E;
12605 Georgian TV - 42°E;
11044 STS 53°E;
11044 STS 53°E;
11044 TELEKANAL 53°E;
11161 STOLICNOE TV 53°E;
11044 Nash Dom 53°E
==================================================
How the AU function for DigiTV [if it still functions, by the time you read this]
(Firstly, I do not know EXACTLY nowadays how and IF it functions, as I gave my Sammy away, so you must play with it a bit to see what works... Now...)
Go to a channel in DigiTV package, then do the following...
Go to EMU Menu, where you should have:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]
I hope you'll soon have the pretty colours...
In addition: do NOT reset the EMU every time you want a provider to AU!!!
Do it just once, after the installation!
Then put the RAM.bin in...
Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...
Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!
==========IN CASE OF TROUBLE===========
If your Sammy must be flashed with a new SW from scratch/zero/from the beginning, as it were - but your screen is black and it keeps giving you these numbers in the display [I had this problem!: 6-01 changing to 6-03 then]:
Kill your Sammy at the back for a few minutes and then...:
When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
If you do not manage the first time - keep trying until you get it right...
But!
Before you do any of that you must make sure you have Sammy connected to a PC via a serial cable and your HyperTerminal prepared, as Papagen already described beautifully:
Or another possibility:
If you have problems uploading a new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well,
1) kill your Sammy at the back and then...
2) when you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
3) Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.
If it times-out [in both cases] - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!
GREAT JOB, MAHDI [& co.]!!!:thum:
HOW TO PROGRAMME YOUR SAMMY
including VIACI, CI, FTA and EMVIA versions
including VIACI, CI, FTA and EMVIA versions
0) One must have Loader 500 or 501 in one's machine [See your basic Settings in the Menu to check it], in order to programme it via a serial 9-pin cable.
If it doesn't work, one must use JTAG to put the Loader 500/501 in, then do the Emu via the serial cable.
Do not hurry, do not cut corners, if you want it all to work properly!
1) Connect Sammy with your PC/laptop
-for an older PC one needs only a serial cable, as chances are it has the serial [9 pin] port
-for a newer PC, if it has no serial but only a USB port, first connect your straight serial 9-pin cable into Sammy, plugging the other end of the cable into a "serial/USB" cable adaptor, so one can plug the other end of the adaptor into the USB port of your PC/laptop
2) Download the following, freshest files to your PC/laptop:
-EMU [the latest Emu is v. 8.4.]
-Tools
-Settings list
-RAM.bin
Unpack them to your PC/lappy, to their respective folders.
The programming itself
3) Switch off the receiver at the back, for 10-20 seconds, then turn it back on again.
4) Start STUDIO 1.5.1 by Maestro MAHDI (choose the right port, for instance COM1 or USB1 or whatever it is in your setup)
-click on DSR FW Loader, then
-Send FW, then
-choose the Emu you want to programme (the latest now is SamsungDSR9500_RVGOLD_V8.4) and then
-Open -> to programme the EMU.
One will see the progress on the LED or maybe on the TV screen, if one is connected to the TV.
WAIT for the CLOCK on Sammy display - do NOT hurry!!!
When it's finished, put the channels list in, using, for instance, Semco Editor.
Btw, SetEdit 1.12 exists, too. It does the job, too!
Receiver must be in Standby mode (using your remote control).
5) Start the Semco Editor (the right port should be chosen, for instance COM1 or USB1), then
-go to File in the upper left corner, then
-to Open
-a new window will appear, to choose a list on your PC (format "something.sdb"), then
-click on Open
-when Semco Editor opens it, click on the Load Data Base From PC To Set Top Box icon.
Wait.
When it is done, quickly do the Emu reset [one must be connected to the TV to see the options], which one does only once now, after programming the Emu:
6) Start Sammy from Standby using your remote and execute RESET OF EMU:
-press 0 + Menu on your remote, quickly, one after the other, then
-choose RESET TO EMU DEFAULTS and
-press OK on your remote.
Sammy should switch itself off now. Start Sammy from Standby using the remote.
{After it resets, you can go back to EMU MENU to make sure you have the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD
...or simply play with whatever Sammy has in RG 8.4 }
[Oh, by the way: sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!]
Now, let's put RAM.bin in [it contains the keys to open the hacked channels...]
7) Sammy is in Standby mode
-Start Samsung DSR Studio 1.5.1 -> choose Ram Editor modus (a special TAB).
-Click on Open File and find the latest RAM.bin on your PC/laptop
-If "Empty Write" is ticked/chosen - remove it.
-Click on Write and wait for "End Write"
Startaj Sammy and watch...
============BY THE WAY+++++++++++++
How to put the keys via remote in
Go to a coded channel and press 0, then Menu [as above] to open the EMU Menu.
At the bottom of the list you'll see Key Editor Menu -> choose a coding system -> Ident -> key one wants to edit.
The scheme is as follows:
0 = 0 Button
1 = 1 Button
2 = 2 Button
3 = 3 Button
4 = 4 Button
5 = 5 Button
6 = 6 Button
7 = 7 Button
8 = 8 Button
9 = 9 Button
A = PG+ Button
B = PG- Button
C = GREEN Button
D = YELLOW Button
E = BLUE Button
F = RED Button
Del = LAST Button
An example (thanx to Dalen)
=====================================
Newer EMU Gold 4.3 has more places/digits to put in.
The procedure is the same, except that one needs to press the EXIT button when finished:
410100xxxxxxxxxxxxxxxx -> EXIT takes you automatically back, having written the key in and the again
410101xxxxxxxxxxxxxxxx -> EXIT and that's it!
===========================================
Thanx to Cruiser:
Thanx to Maumixio, how to enter a DCW:
===========================================
Thanx to Cruiser for the list of channels which can be seen using Sammy's Emu and RAM.bin file/keys:
N*gra:
DigiTV 1°W ok key 00-17.06.09.
Tv Globo 13°E ok
Multicanal 30°W
Seca:
RAI 13°E- ok next key 0D July
Mediatech 4°W- ok next key 0D July
Cryptoworks:
Kingston 5°E
Jetix 13° 10723/H/29900
Cartoon Network & TNT Germany ok 9°E 11728/V/27500
Viaccess:
Mezzo 13°E 12245/H/27500
SIC Int. 16°E 12568/H/3703
MCM Belgique 5°W 12543/H/27500
Biss Channel:
12149 TVE 1 30°W;
11931 LDTV 30°W;
12149 TVM 2 30°W;
12092 AXN PORTUGAL 30°W;
11474 TV CANARIA 30°W;
12735 ENTV 15°W;
11177 FOX TV 12,5°W;
11373 TOUCH TV 12,5°W;
11188 FOX GERMANY 12,5°W;
11066 Fox Sport 8°W; new PMT
11066 Discovery 8°W;
11066 Fox news 8°W;
12583 2M 12,5°W;
11423 AL RIYADIAH 7°W;
11065 Canal 6 Feed 5°W
11065 ENTV 5°W
12543 FOX LIFE 5°W;
10722 MEGASPORT 4°W;
10722 TV KYIV 4°W;
10722 1PLUS1 4°W;
10759 Qtv 4°W;
11766 TET 5°E;
12073 OCK 5°E;
11823 S2K (Sat 2000) 9°E;
11296 S2K (Sat 2000) 13°E;
12673 TVM MAROC 13°E;
11643 MBC US 26°E;
12608 IMED 42°E;
11894 Ans TV 42°E
11178 Ekin Turk TV (USUK TV) 42°E;
12678 24 42°E;
12593 RUSTAVI 2 42°E;
11054 NTV SPOR 42°E;
11607 AZERBAYCAN TV 42°E;
11870 TV8 42°E;
12605 Georgian TV - 42°E;
11044 STS 53°E;
11044 STS 53°E;
11044 TELEKANAL 53°E;
11161 STOLICNOE TV 53°E;
11044 Nash Dom 53°E
==================================================
How the AU function for DigiTV [if it still functions, by the time you read this]
(Firstly, I do not know EXACTLY nowadays how and IF it functions, as I gave my Sammy away, so you must play with it a bit to see what works... Now...)
Go to a channel in DigiTV package, then do the following...
Go to EMU Menu, where you should have:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]
I hope you'll soon have the pretty colours...
In addition: do NOT reset the EMU every time you want a provider to AU!!!
Do it just once, after the installation!
Then put the RAM.bin in...
Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...
Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!
==========IN CASE OF TROUBLE===========
If your Sammy must be flashed with a new SW from scratch/zero/from the beginning, as it were - but your screen is black and it keeps giving you these numbers in the display [I had this problem!: 6-01 changing to 6-03 then]:
Kill your Sammy at the back for a few minutes and then...:
When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
If you do not manage the first time - keep trying until you get it right...
But!
Before you do any of that you must make sure you have Sammy connected to a PC via a serial cable and your HyperTerminal prepared, as Papagen already described beautifully:
Or another possibility:
If you have problems uploading a new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well,
1) kill your Sammy at the back and then...
2) when you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
3) Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.
If it times-out [in both cases] - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!
GREAT JOB, MAHDI [& co.]!!!:thum:
Hi
QUOTE=gorski;518027]
0) One must have Loader 500 or 501 in one's machine [See your basic Settings in the Menu to check it], in order to programme it via a serial 9-pin cable.
If it doesn't work, one must use JTAG to put the Loader 500/501 in, then do the Emu via the serial cable.
Do not hurry, do not cut corners, if you want it all to work properly!
1) Connect Sammy with your PC/laptop
-for an older PC one needs only a serial cable, as chances are it has the serial [9 pin] port
-for a newer PC, if it has no serial but only a USB port, first connect your straight serial 9-pin cable into Sammy, plugging the other end of the cable into a "serial/USB" cable adaptor, so one can plug the other end of the adaptor into the USB port of your PC/laptop
2) Download the following, freshest files to your PC/laptop:
-EMU [the latest Emu is v. 8.4.]
-Tools
-Settings list
-RAM.bin
Unpack them to your PC/lappy, to their respective folders.
The programming itself
3) Switch off the receiver at the back, for 10-20 seconds, then turn it back on again.
4) Start STUDIO 1.5.1 by Maestro MAHDI (choose the right port, for instance COM1 or USB1 or whatever it is in your setup)
-click on DSR FW Loader, then
-Send FW, then
-choose the Emu you want to programme (the latest now is SamsungDSR9500_RVGOLD_V8.4) and then
-Open -> to programme the EMU.
One will see the progress on the LED or maybe on the TV screen, if one is connected to the TV.
WAIT for the CLOCK on Sammy display - do NOT hurry!!!
When it's finished, put the channels list in, using, for instance, Semco Editor.
Btw, SetEdit 1.12 exists, too. It does the job, too!
Receiver must be in Standby mode (using your remote control).
5) Start the Semco Editor (the right port should be chosen, for instance COM1 or USB1), then
-go to File in the upper left corner, then
-to Open
-a new window will appear, to choose a list on your PC (format "something.sdb"), then
-click on Open
-when Semco Editor opens it, click on the Load Data Base From PC To Set Top Box icon.
Wait.
When it is done, quickly do the Emu reset [one must be connected to the TV to see the options], which one does only once now, after programming the Emu:
6) Start Sammy from Standby using your remote and execute RESET OF EMU:
-press 0 + Menu on your remote, quickly, one after the other, then
-choose RESET TO EMU DEFAULTS and
-press OK on your remote.
Sammy should switch itself off now. Start Sammy from Standby using the remote.
{After it resets, you can go back to EMU MENU to make sure you have the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD
...or simply play with whatever Sammy has in RG 8.4 }
[Oh, by the way: sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!]
Now, let's put RAM.bin in [it contains the keys to open the hacked channels...]
7) Sammy is in Standby mode
-Start Samsung DSR Studio 1.5.1 -> choose Ram Editor modus (a special TAB).
-Click on Open File and find the latest RAM.bin on your PC/laptop
-If "Empty Write" is ticked/chosen - remove it.
-Click on Write and wait for "End Write"
Startaj Sammy and watch...
============BY THE WAY+++++++++++++
How to put the keys via remote in
Go to a coded channel and press 0, then Menu [as above] to open the EMU Menu.
At the bottom of the list you'll see Key Editor Menu -> choose a coding system -> Ident -> key one wants to edit.
The scheme is as follows:
0 = 0 Button
1 = 1 Button
2 = 2 Button
3 = 3 Button
4 = 4 Button
5 = 5 Button
6 = 6 Button
7 = 7 Button
8 = 8 Button
9 = 9 Button
A = PG+ Button
B = PG- Button
C = GREEN Button
D = YELLOW Button
E = BLUE Button
F = RED Button
Del = LAST Button
An example (thanx to Dalen)
=====================================
Newer EMU Gold 4.3 has more places/digits to put in.
The procedure is the same, except that one needs to press the EXIT button when finished:
410100xxxxxxxxxxxxxxxx -> EXIT takes you automatically back, having written the key in and the again
410101xxxxxxxxxxxxxxxx -> EXIT and that's it!
===========================================
Thanx to Cruiser:
Thanx to Maumixio, how to enter a DCW:
===========================================
Thanx to Cruiser for the list of channels which can be seen using Sammy's Emu and RAM.bin file/keys:
N*gra:
DigiTV 1°W ok key 00-17.06.09.
Tv Globo 13°E ok
Multicanal 30°W
Seca:
RAI 13°E- ok next key 0D July
Mediatech 4°W- ok next key 0D July
Cryptoworks:
Kingston 5°E
Jetix 13° 10723/H/29900
Cartoon Network & TNT Germany ok 9°E 11728/V/27500
Viaccess:
Mezzo 13°E 12245/H/27500
SIC Int. 16°E 12568/H/3703
MCM Belgique 5°W 12543/H/27500
Biss Channel:
12149 TVE 1 30°W;
11931 LDTV 30°W;
12149 TVM 2 30°W;
12092 AXN PORTUGAL 30°W;
11474 TV CANARIA 30°W;
12735 ENTV 15°W;
11177 FOX TV 12,5°W;
11373 TOUCH TV 12,5°W;
11188 FOX GERMANY 12,5°W;
11066 Fox Sport 8°W; new PMT
11066 Discovery 8°W;
11066 Fox news 8°W;
12583 2M 12,5°W;
11423 AL RIYADIAH 7°W;
11065 Canal 6 Feed 5°W
11065 ENTV 5°W
12543 FOX LIFE 5°W;
10722 MEGASPORT 4°W;
10722 TV KYIV 4°W;
10722 1PLUS1 4°W;
10759 Qtv 4°W;
11766 TET 5°E;
12073 OCK 5°E;
11823 S2K (Sat 2000) 9°E;
11296 S2K (Sat 2000) 13°E;
12673 TVM MAROC 13°E;
11643 MBC US 26°E;
12608 IMED 42°E;
11894 Ans TV 42°E
11178 Ekin Turk TV (USUK TV) 42°E;
12678 24 42°E;
12593 RUSTAVI 2 42°E;
11054 NTV SPOR 42°E;
11607 AZERBAYCAN TV 42°E;
11870 TV8 42°E;
12605 Georgian TV - 42°E;
11044 STS 53°E;
11044 STS 53°E;
11044 TELEKANAL 53°E;
11161 STOLICNOE TV 53°E;
11044 Nash Dom 53°E
==================================================
How the AU function for DigiTV [if it still functions, by the time you read this]
(Firstly, I do not know EXACTLY nowadays how and IF it functions, as I gave my Sammy away, so you must play with it a bit to see what works... Now...)
Go to a channel in DigiTV package, then do the following...
Go to EMU Menu, where you should have:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]
I hope you'll soon have the pretty colours...
In addition: do NOT reset the EMU every time you want a provider to AU!!!
Do it just once, after the installation!
Then put the RAM.bin in...
Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...
Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!
==========IN CASE OF TROUBLE===========
If your Sammy must be flashed with a new SW from scratch/zero/from the beginning, as it were - but your screen is black and it keeps giving you these numbers in the display [I had this problem!: 6-01 changing to 6-03 then]:
Kill your Sammy at the back for a few minutes and then...:
When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
If you do not manage the first time - keep trying until you get it right...
But!
Before you do any of that you must make sure you have Sammy connected to a PC via a serial cable and your HyperTerminal prepared, as Papagen already described beautifully:
Or another possibility:
If you have problems uploading a new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well,
1) kill your Sammy at the back and then...
2) when you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
3) Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.
If it times-out [in both cases] - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!
GREAT JOB, MAHDI [& co.]!!!:thum:[/QUOTE]
:mecry:I see in my sammy:File CheckSum:1BF9
File Size:1631 KB
Port Open
Upload Start
Upload End
This for after few seconds???!!and Downloading software...stooped!
In SemcoEditor start the upload the Setting,but the few seconds trassmision closing???!!!Thanx!
QUOTE=gorski;518027]
HOW TO PROGRAMME YOUR SAMMY
including VIACI, CI, FTA and EMVIA versions
including VIACI, CI, FTA and EMVIA versions
0) One must have Loader 500 or 501 in one's machine [See your basic Settings in the Menu to check it], in order to programme it via a serial 9-pin cable.
If it doesn't work, one must use JTAG to put the Loader 500/501 in, then do the Emu via the serial cable.
Do not hurry, do not cut corners, if you want it all to work properly!
1) Connect Sammy with your PC/laptop
-for an older PC one needs only a serial cable, as chances are it has the serial [9 pin] port
-for a newer PC, if it has no serial but only a USB port, first connect your straight serial 9-pin cable into Sammy, plugging the other end of the cable into a "serial/USB" cable adaptor, so one can plug the other end of the adaptor into the USB port of your PC/laptop
2) Download the following, freshest files to your PC/laptop:
-EMU [the latest Emu is v. 8.4.]
-Tools
-Settings list
-RAM.bin
Unpack them to your PC/lappy, to their respective folders.
The programming itself
3) Switch off the receiver at the back, for 10-20 seconds, then turn it back on again.
4) Start STUDIO 1.5.1 by Maestro MAHDI (choose the right port, for instance COM1 or USB1 or whatever it is in your setup)
-click on DSR FW Loader, then
-Send FW, then
-choose the Emu you want to programme (the latest now is SamsungDSR9500_RVGOLD_V8.4) and then
-Open -> to programme the EMU.
One will see the progress on the LED or maybe on the TV screen, if one is connected to the TV.
WAIT for the CLOCK on Sammy display - do NOT hurry!!!
When it's finished, put the channels list in, using, for instance, Semco Editor.
Btw, SetEdit 1.12 exists, too. It does the job, too!
Receiver must be in Standby mode (using your remote control).
5) Start the Semco Editor (the right port should be chosen, for instance COM1 or USB1), then
-go to File in the upper left corner, then
-to Open
-a new window will appear, to choose a list on your PC (format "something.sdb"), then
-click on Open
-when Semco Editor opens it, click on the Load Data Base From PC To Set Top Box icon.
Wait.
When it is done, quickly do the Emu reset [one must be connected to the TV to see the options], which one does only once now, after programming the Emu:
6) Start Sammy from Standby using your remote and execute RESET OF EMU:
-press 0 + Menu on your remote, quickly, one after the other, then
-choose RESET TO EMU DEFAULTS and
-press OK on your remote.
Sammy should switch itself off now. Start Sammy from Standby using the remote.
{After it resets, you can go back to EMU MENU to make sure you have the following configuration:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD
...or simply play with whatever Sammy has in RG 8.4 }
[Oh, by the way: sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!]
Now, let's put RAM.bin in [it contains the keys to open the hacked channels...]
7) Sammy is in Standby mode
-Start Samsung DSR Studio 1.5.1 -> choose Ram Editor modus (a special TAB).
-Click on Open File and find the latest RAM.bin on your PC/laptop
-If "Empty Write" is ticked/chosen - remove it.
-Click on Write and wait for "End Write"
Startaj Sammy and watch...
============BY THE WAY+++++++++++++
How to put the keys via remote in
Go to a coded channel and press 0, then Menu [as above] to open the EMU Menu.
At the bottom of the list you'll see Key Editor Menu -> choose a coding system -> Ident -> key one wants to edit.
The scheme is as follows:
0 = 0 Button
1 = 1 Button
2 = 2 Button
3 = 3 Button
4 = 4 Button
5 = 5 Button
6 = 6 Button
7 = 7 Button
8 = 8 Button
9 = 9 Button
A = PG+ Button
B = PG- Button
C = GREEN Button
D = YELLOW Button
E = BLUE Button
F = RED Button
Del = LAST Button
An example (thanx to Dalen)
=====================================
Newer EMU Gold 4.3 has more places/digits to put in.
The procedure is the same, except that one needs to press the EXIT button when finished:
410100xxxxxxxxxxxxxxxx -> EXIT takes you automatically back, having written the key in and the again
410101xxxxxxxxxxxxxxxx -> EXIT and that's it!
===========================================
Thanx to Cruiser:
Thanx to Maumixio, how to enter a DCW:
===========================================
Thanx to Cruiser for the list of channels which can be seen using Sammy's Emu and RAM.bin file/keys:
N*gra:
DigiTV 1°W ok key 00-17.06.09.
Tv Globo 13°E ok
Multicanal 30°W
Seca:
RAI 13°E- ok next key 0D July
Mediatech 4°W- ok next key 0D July
Cryptoworks:
Kingston 5°E
Jetix 13° 10723/H/29900
Cartoon Network & TNT Germany ok 9°E 11728/V/27500
Viaccess:
Mezzo 13°E 12245/H/27500
SIC Int. 16°E 12568/H/3703
MCM Belgique 5°W 12543/H/27500
Biss Channel:
12149 TVE 1 30°W;
11931 LDTV 30°W;
12149 TVM 2 30°W;
12092 AXN PORTUGAL 30°W;
11474 TV CANARIA 30°W;
12735 ENTV 15°W;
11177 FOX TV 12,5°W;
11373 TOUCH TV 12,5°W;
11188 FOX GERMANY 12,5°W;
11066 Fox Sport 8°W; new PMT
11066 Discovery 8°W;
11066 Fox news 8°W;
12583 2M 12,5°W;
11423 AL RIYADIAH 7°W;
11065 Canal 6 Feed 5°W
11065 ENTV 5°W
12543 FOX LIFE 5°W;
10722 MEGASPORT 4°W;
10722 TV KYIV 4°W;
10722 1PLUS1 4°W;
10759 Qtv 4°W;
11766 TET 5°E;
12073 OCK 5°E;
11823 S2K (Sat 2000) 9°E;
11296 S2K (Sat 2000) 13°E;
12673 TVM MAROC 13°E;
11643 MBC US 26°E;
12608 IMED 42°E;
11894 Ans TV 42°E
11178 Ekin Turk TV (USUK TV) 42°E;
12678 24 42°E;
12593 RUSTAVI 2 42°E;
11054 NTV SPOR 42°E;
11607 AZERBAYCAN TV 42°E;
11870 TV8 42°E;
12605 Georgian TV - 42°E;
11044 STS 53°E;
11044 STS 53°E;
11044 TELEKANAL 53°E;
11161 STOLICNOE TV 53°E;
11044 Nash Dom 53°E
==================================================
How the AU function for DigiTV [if it still functions, by the time you read this]
(Firstly, I do not know EXACTLY nowadays how and IF it functions, as I gave my Sammy away, so you must play with it a bit to see what works... Now...)
Go to a channel in DigiTV package, then do the following...
Go to EMU Menu, where you should have:
EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]
I hope you'll soon have the pretty colours...
In addition: do NOT reset the EMU every time you want a provider to AU!!!
Do it just once, after the installation!
Then put the RAM.bin in...
Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...
Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!
==========IN CASE OF TROUBLE===========
If your Sammy must be flashed with a new SW from scratch/zero/from the beginning, as it were - but your screen is black and it keeps giving you these numbers in the display [I had this problem!: 6-01 changing to 6-03 then]:
Kill your Sammy at the back for a few minutes and then...:
When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
If you do not manage the first time - keep trying until you get it right...
But!
Before you do any of that you must make sure you have Sammy connected to a PC via a serial cable and your HyperTerminal prepared, as Papagen already described beautifully:
Or another possibility:
If you have problems uploading a new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well,
1) kill your Sammy at the back and then...
2) when you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
3) Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.
If it times-out [in both cases] - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!
GREAT JOB, MAHDI [& co.]!!!:thum:[/QUOTE]
:mecry:I see in my sammy:File CheckSum:1BF9
File Size:1631 KB
Port Open
Upload Start
Upload End
This for after few seconds???!!and Downloading software...stooped!
In SemcoEditor start the upload the Setting,but the few seconds trassmision closing???!!!Thanx!