Dragon/T-Rex Cam FAQ Thread

Status
Not open for further replies.
C

costa46

Dragon/T-Rex Cam FAQ Thread

ps:- NEVER , NEVER , NEVER auto-detect your cards or they will require the repair files to repair them before you can use them for programming

ensure you KNOW which card you have , the older card is pic based , the newer card is a funcard 7 , also known as a prussian 5 card and says * Fun7 on it. The newest cards say f84a on them and are pic based once more

also remember that the card usually goes into a programmer with the contacts on the underside , but when placed into the cam the contacts should be on the upperside when reprogramming the cam

please note that there are only 2 types of files that can be used in your dragon cam

1) firecrypt ( the firmware it came with )

2) predator

nothing else can be used , and you cannot update the chip firmware from say v2.06 to v3 or v4 , once its programmed at the factory , it stays that way

************************************************** *

Some peeps think the loader card has to be kept in the cam. Like the old days...

It doesn't work like that.

The loader "loads" the firmware (information of channels and encryptions), and once done, YOU HAVE TO REMOVE THE CARD, and restart receiver for the Dragon to work.

And in the event of any code changes the channels are "updated" in the Debug section of your cam menu.

I know this may seem "obvious" to you experts but some newbies aren't aware of this

************************************************** ****

in response to questions about what kit is required !!!!!!!!!


nowadays you need a suitable funcard 7 programmer , I use the yellow adteknik 3.6 usb myself

usually the dragon should come with a funcard 7 loader card


thats all you need for almost everything available , but sometimes additional cards are required , like vr3 , opus , cerebro etc


and if you already have a suitable programmer , use it

examples:-

adteknik 3.6 usb ( yellow ) - either loader card
elvis (serial) by adteknik - funcard 7 loader card only
dynamite usb
infinity phoenix usb
infinity usb
infinity unlimited
cas2 with addon
cas 3

etc

************************************************** ****

please note there is only ONE WAY to program your dragon cam at the moment

that is with a dragon loader card

the old loader card was a pic based card
( the one I use myself )

the newer loader card is a funcard 7

only these 2 cards can be used , nothing else so dont ask !!!!!


so questions like:-


cas2 on its own ?? = NO
( use the cas2 addon to program the loader card )

cas 1 or cas plus ? = NO

pcmcia slot on a laptop/notebook etc ?? = NO

any other method ?? = NO

**********************************************
example1 :-

dragon + cas 2

can you program a dragoncam using a cas 2?

yes you can but you need the add on

and you still need the loader card

ie:- you cannot reprogram the cam using the cas2 , only by using the loader card , which is either a special pic based card OR by using a funcard 7

the cas2 and addon are used to program the loader card , the loader is then used to program the cam

************************************************** *

dragon and cas 3

You don't use the CAS 3 to programme a loader card (although you could).
You plug the Dragon into the CAM slot & then insert a dummy card on a ribbon cable.
This allows you to program the Dragon directly

************************************************** ****

nb:- the dra and bin files are exactly the same file but with a different suffix

so you can easily rename the files to .dra or .bin as required

there is nothing else to it , simple as that

************************************************** ****

Sim Card ..

This Card is for the 2 InXtc Tv and XPlus Tv
both on HB Freq:10852 Hor 27500 3/4.

Just take the SIM Card out of the Larger Card carefully and Open your Dragon/T-Rex Cam Sim Card Holder and slip the Card in with the Chips facing down into the Cam (just look where the Corner has been cut off) into Holder..clip the Holder back into Cam carefully so as NOT to Bend it in anyway and Insert into STB go to the Channels mentioned and start viewing...

First time Activation takes a little while to kick in but dont get impatient..
It WILL work..
Enjoy.

One little TIP write the Date of the Activation on the Card with a Marker Pen so that you can see if it works for your promised Sub..(9 Months or 1 Year.)
You should do this on ALL your Sub Cards.

Programming your Dragon Cam Using Infinity Pheonix USB @6mhz


For Predatorxxx read as Predator v3.32 or whatever version you are loading

Unzip Predatorxxx.zip file to a directory of your choice it has several files in but the one we want is the Predatorxxx.dra file

Do not insert card until you start your programmer. I use the Infinity USB program. DO NOT allow the programmer to auto detect the loader card.

Start “Dragonload.exe”
Then you need the Dragon loader card inserted in the Infinity USB programmer before you press connect otherwise you will get the message “Unable to Connect, check setting, programmer and card”
Press “Program card” point program to the Predatorxxx.dra and click on it. The card should load (sometimes you have to do that bit twice) When it says something like “Card Loaded” remove card and move on to the Receiver with the Dragon cam inserted and on a Free to air channel (I usually use Rai 1 on Hotbird)

Turn off receiver and insert Loader card then power on. In cam menu it should say something like "dragon loader" click ok it will then say if you really want to load click ok and away you go you will have to press refresh a few times to check it up loading it will take about 10mins when its completed remove loader card restart receiver and away you go you should have the latest Predator loaded.

Livewirex

************************************************** **

or using infinity and v1.48 software and funcard 7

dragon funcard 7 programming

in version 1.48 direct dragon loadercard programming support is included,

you have to choose prussian 5 card and select proper files -

fun7 flash,

predator .dra file (not bin one) and if it ask you for spanning type select reverse spanning of file into eeproms (2nd choice)

everything else is automatic.

cheers
dolehaj

-----------------------------------------------------------------------

OR

ps:- found this too ( with a few amendments by me )

1 download predator 3.32 from toecutters den or dragonmodule
2 you will also need dragon loader file too.
3 save predator 3.32 file to desk top after unpacking with winrar or winzip
4 open the latest infinity program and put in phoenix mode 6 mhz
5 open dragon loader. in setting make sure same com port as infinity
6 find predator file on desk top and open
7 press connect should go green .prog file away you go.
7 put loader card in dragon cam. put cam in sat box
8 put sat on fta channel. turn sat box off then back on again
9 go to the cam menu look for dragonload, press load and wait until it says loading successful.
10 when all is done exit and turn sat box off. take loader card out , it has done its job.
11 turn sat box on . and have fun

**************************************************

OR

for a funcard 7 using an infinity programmer

Select Prussian 5
select flash and write fun7ldr hex (only if card is detected or damaged by other use)
select ext eep 1 and load bin1 file
select ext eep 2 and load bin2 file
select write

PS Bin file or avg update file are the same
 
C

costa46

ELVIS INSTRUCTIONS BY TJ1965

for the older serial "elvis" and definitely for the yellow 3.6 usb "elvis"

using multiprog v1.80 or v1.90, or later !!!


ALTERNATIVE METHOD
For this method, you need a FUN7 card
Using a suitable program, program the FLASH of the FUN7 card with FUN7LDR.HEX,
and program the EEPROM with predator2XX.bin. Make sure the program you use
handle the large eeprom size of the fun7 card correctly!
END alternative method

Insert the programmed card into the Dragon module. Insert this into a receiver
and turn on the receiver. make sure you are tuned to an FTA channel.

Go to the Common interface menu on the receiver, and select the "Dragon Loader" module.
In the next menu, select "yes, Load module".
Now a menu appears indicating that loading is in progress. To see the actual progress percentage,
select *********. There is no auto-refresh because some receivers had problems with that....

When loading is complete, a menu appears saying "Loading successful". REMOVE the loader
card from the module, and switch off and turn back on the receiver.

************************************************** ******

there are two type of dragonloader cards.
The first one was a pic based card (PIC16F84A).
The second one, is just a Fun7 (2x24LC1024) and it is marked as Fun7.
As an alternative, a standard Fun7 can be used as a dragonloader card.

To program the Fun7 based loader card, or a standard Fun7 card I recomend this way of doing it, since it is the fastest and easiest way of doing it. The best thing is that it also works on the serial version of the programmer, and it takes less than 2 minutes.

Go to the Funcard tab
Give the project a suitable name.
Load the *.dra file as external eeprom.Select EEprom as 2x24LC1024.
Fun7Ldr.hex as Flash (this file is normally distributed with the .dra file).
Leave (or make sure that) internal ee is unticked.
Press program, and wait about two minutes.

If this fails, it is most probably because the loadercard is read protected, and therefore needs to be erased. To do this, tick all three tickboxes for the memory, press erase, and try again.

************************************

To program the picbased card, one needs to have the USB version of the programmer, the old serial version can't handle this card.

Go to the Dragonloader tab.
Give the project a name. Load the *.dra file, and select DragonLoader as card type. Then just press program, sit back and wait, since it takes a while.
This way of loading works for Fun7 based cards to, but it is much slower.

best regards
TJ


ps:- please note that the serial version of an elvis cannot program the pic version of the card because it does not have the 6.00 mhz phoenix mode required for this task

both of them ( serial and usb ) can program a funcard 7 ( prussian 5 )************************************************* * ******

for the ORANGE adteknik usb phoenix programmer

1) downloaded a proggy that told me which com port it was using it said 4.

2) I used my vx multi pro to load flash set as fun 2 (as it has no support for fun 7) but ANY funcard programmer will do this task as they all can manage a funcard 2

3) then using t.j.s banana dragon load software to load the latest .dra file it worked a treat.

before this all i got was a please remove card message. hope this helps. gaz1969

ps:- use the dragon loader software downloaded from the adteknik site set it to com 4 ( or whatever your com port actually is )
load the latest .dra file and press program
as long as you have the flash loaded on the card everything should be ok.
otherwise make sure you have programmed the funcard 7 with the flashloader first , then follow the above procedure
 
C

costa46

dynamite programmer instructions :- by stuartrob

Programming Dragon Cam with Dynamite

-------------------------------------------------------------------------

For an Echostar 2110, Dragon cam and Dynamite programmer and pic loader card

1. Make sure the Dynamite programmer is not connected to the usb.
2. Enter your internet connection
3. Go to _www.duolabs.com and select dynamite downloads.
4. Download Jungo driver 6.22
5. Download Dynamite set-up 2.6
6. Download the Predator xxx zip files.
7. Close the internet connection.
8. Unzip the Dynamite set-up
9. Unzip the Jungo Drivers
10. Unzip the Predator files.
11. Run the program called dynamite_setup26.exe
12. The setup will ask for the drivers, point it to the unzipped Jungo driver
13. At the end, click finish.
14. Shut down the computer and re-start.
15. Plug in the Dynamite programmer.
16. Go to the control panel and view system device manager and check that the Jungo is loaded.
17. Click on Jungo and ensure Dynamite is loaded the driver should have 9-7-2004 date (lastest on writing).
18. Close the control panel.
19. Open Dynamite 2.6 from the screen for some reason it tries to connect to the internet. Ignore the connection.
20. The screen should show ‘dynamite connected, Rel. 2.6 – Drv 6.22’ and the serial number at the bottom of the small screen.
21. Click on Phoenix. Click on button marked Phoenix @ 6.00 Mhz. Then click on the << at the top of the page to take you back to the first screen.
22. Enter the loader card into the programmer.
23. Press programmer and the ‘Loading Module’ will show, then the programmer screen. Ensure that the GoldWafer card is found and that it has the option of repairing the Dragon Card Loader.
24. Press on the Dragon Card Loader. It will set the card to the default for loading the cam. When the Flash memory and Internal EEPROM have been loaded a subform will say done. Click on this button. Close down this module.
25. Close the programmer and click on the OS Card button and choose the Dragon Card.
26. Find your *.dra unzipped file and enter it in the Firmware box.
27. Press the button ‘Write to Card’
28. A message will confirm that it is written to the card.
29. Remove the card.
30. Tune to a FTA signal and turn the satellite receiver is off.
31. Enter the Dragon loader card in the cam (contact face up)
32. Switch on the receiver.
33. Enter menu and select conditional access, it will take about 30 seconds to load this, then on the common Interface select Dragon Load.
34. It will ask to Load now, highlight and press ok on the remote.
35. It will take about 10 mins to load.
36. Loading complete will show when done.
37. Turn off the receiver by the remote, Remove the dragon loader card, count 20 seconds and then turn it back on.
38. If all is well, great!

__________________________________________________ _______________


dynamite programmer instructions

Programming Dragon Cam with Dynamite and fun7 loader card


open dynamite insert card CHIP FACE DOWN click PROG

where it says FunCard click arrow and change to PrussianCard5
it should now say it's a FunCard7 with 2X24LC1024

click flash memory folder and find FUN7LDR.HEX if you have it look at recent predator files
and program

IT'S NOW A DRAGONLOADER CARD

so from now on you only click the the DRAGON on the Dynamite main option

and you use the DRA file
 
C

costa46

programming a dragon loader card with the cas2 and its add-on:-

1. start the CASII-Soft --> now you are in the main-menu
2. click the button "PROG"
3. put the Fun7 into the cardreader
4. choose the type "Prussian 5"
5. click the button erase and wait until the card is completely erased
6. click the button on the right side "Repair Dragon Card Loader"
....and wait until the loader will be written to the card
8. now you can close this window and you are back in the main-menu again
9.click the button "DRAGON" --> a new window opens and the message "Dragon Card Loader detected"
10.click the folder-icon and choose the *.dra-file
11.click the button "Write to Dragon Loader Card" and wait until the card will be written.

Congratulation your Dragonloadercard is written successfully

Now put it into your Dragon-Cam to upgrade the Predator.

************************************************** ****

programming a dragon/trex cam with the cas3:-


You don't use the CAS 3 to programme a loader card (although you could if you want to).
You plug the Dragon into the CAM slot & then insert a dummy card on a ribbon cable.
This allows you to program the Dragon directly using the cas studio software
 
C

costa46

Patching with DCP

-------------------------------------------------------------------------

Softcam Patch

1) Get the latest DCP software,patchtables,Predator firmware (check the Dragoncam stickys here) and softcam file (Mach1's works well).
2)Unzip patchtable,Predator and softcam files into a known area of your hard drive (IE: My Documents).
3) Open the DCP.exe, you will see "step-by-step" areas 1,2 and 3 have folder icons, use these to load the patchtables,Predator firmware and finally the softcam file.
4) Click option 4 "Patch and save Firmware" this will ask you where you want to save your patched file. Once saved you can use this file to program your dragon loader card in the normal way.

Con@x key patch

1) Get the latest DCP software,patchtables, Predator firmware (check the Dragoncam stickys here) and finally the con@x key.
2) Unzip patchtable and Predator files into a known area of your hard drive (IE: My Documents)
3) Open the DCP.exe, you will see "step-by-step" use the folder icons in areas 1 and 2 to load the current patchtables and Predator firmware.
4) Click on the key icon at the bottom of the DCP page then scroll down to the bottom where you will see the various con@x keys.
5) Copy and paste the full key string* (NO gaps) in the correct area (20,21,22 or 23)
6) Patch and save by clicking the first icon (page folder) at the bottom of the DCP page then option 4, this will ask you where you want to save your patched file. Once saved you can use this file to program your dragon loader card in the normal way.

*To make a usable key string first join up the exp numbers, then the mod numbers. You then join the exp and mod together so you have a continuous string that starts with the exp numbers. You may find the key string is ready made depending on your source.
 
C

costa46

Programmer manuals for loading FUN7 loadercards ( by Parker )

When you detect your loadercard or use it for other purpose your flash is damaged and you have to repair it with Loader repairfile so look in the software section

Why not autodetect:
Whats happening when you detect your card?
For autodetect a card, the programmer need to overwrite the flash with a small code who answer to programmer with the card characteristics.
The original flash is destroyed by this writing and become unuseable, you need to repair your Dragoncard flash with a correct image flash (Fun7ldr.hex) or (LDR2MB.HEX)

For most programmers there are different approaches to program but this manual shows you the quickest and easiest way to program your card
This Page will be in progress with your help
If there is a new soft or programmer which do the trick with the FUN7 ,make a brief how to in steps like shown below and PM me Parker Thanks in advance


Keep your gear uptodate and ALWAYS use the newest software!!!!!


A Infinity usb (typical when using dra file only)
B Infinity usb (using splitted files like JFK, this works on other usb programmers too)
C Infinity usb phoenix (also for all other phoenix 6mhz prog)
D Cas II addon
E Dynamite programmer
F Elvis serial programmer
G Adteknik programmer Yellow usb and Orange usb
H Vxmulti 2 pro



AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA

Infinity USB programmer
When using one firmware file predator DRA
1 start programmer software
2 select prussian 5 (= fun7)
3 select flash (only if card is detected or used for other purpose)
4 select LDR.FUN7.HEX on flash (delivered by all the predators)
5 select Ext EEP1
6 open firmware file predator x.xx dra (not bin)
7 span option apears, select option 2 Revers span
8 select write


BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB BB

When using splitted file like JFK files for USB programmers like the Infinity usb, Uniplat usb and all other usb programmers who can handle fun7 cards
1 start programmer software
2 select prussian5 (=fun7)
3 select flash
4 select LDR.FUN7.HEX on flash (delivered by all the predators)
5 select Ext EEP1 and open fun7 eeprom1 hex
6 select Ext EEP2 and open fun7 eeprom2 hex
7 select write


CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CC

Infinity usb Phoenix in phoenix mode (als for all other phoenix 6mhz programmers)
1 start programmer software
2 select phoenix mode
3 popup appears, here you select phoenix 6mhz
4 The screen disapear and a icoon appears in the taskbar below
5 Open dragonloader exe
6 click on connect (in some cases you have to do this several times)
7 select program card
8 open your Predator dra file (not bin)
9 popup appears Programming progress when the bar is full the card is loaded

Note :In A lot of cases The Mastercrd6 need to be set in mouse 6mhz mode to do the Job

DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD DD


1. start the CASII-Soft --> now you are in the main-menu

Notice:
Steps 2 to 8 are only usefull, if the LoaderCard is new, or the Loader is damaged.
Otherwise you have to go to step 9.

2. click the button "PROG"
3. put the loadercard (Fun7) into the cardreader
4. the program will detect a FUN-Card (if automatic detection is enabled)
5. choose the type "Prussian 5"
6. click the button erase and wait until the card is completely erased
7. click on the right side the button "Repair Dragon Card Loader"
...and wait until the loader will be written to the card
8. and now you can close this window --> now you are in the main-menu again

9.click the button "DRAGON" --> a new window opens and the message "Dragon Card Loader detected"
10.click the folder-icon and choose the *.dra-file
11.click the button "Write to Dragon Loader Card" and wait until the card will be written.

Congratulation your Dragonloadercard is written successfully

By bigwaller

EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE EEEE

Dynamite programmer
1 Start the programmer software
2 select smartcard
3 select OS with dragon logo
4 select firmware and open your file (predator x.xx DRA)
5 select write to dragonloadercard
If the bar is totaly blue, you can remove the card and program your cam with it



FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF FFFFF

Elvis programmer
Adteknik

For serial and yellow 3.6 usb elvis programmers

FUN7 for both versions
Use software multiprog 1.80 or 1.90 later

1 open multiprog 1.90
2 select fun
3 select Ext ee --> 2x 24C1024
4 select and load external eeprom and load firmware dra file Predator x.xx
5 select and load the fun7ldr file to the flash section
6 do not load anything in the internal eeprom section and leave unticked
7 select Program and the card will be loaded , wait until its finished


SINGLE PIC only usb version

1 select single chip
2 select chip (pic 16F84A)
3 select load and load the firmware predator x.xx
4 select program and the card will be loaded


Loader repair single pic
1.open multi prog 1.80 or later
2.select single chips
3.select Chip (pic 16F84A)
4.select load and load LDR2MB.HEX
5.select program

Loader repair FUN7
1. open multi prog 1.80 or later
2. select megapic/MII/titanium/Dragonloader
3. select card
4. select dragonloader and load (fun7ldr.hex)
5. select program

Note By use of battery with old elvis the result is not how it should be, the reciever will say "card does not have a valid image" when you use a power supply 9 to 12 v the problem would be solved

GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG GGGGGGGGGG

Orange adteknik

1.Open Dragoncardloader AD USB sm/phoenix v1.1 or newer
2.Select file
3.Load your file
4.Select program

HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHH


Vx multi pro/ Mastera / mastercard / SC-Master

1.Switch loader in 0 mode Phoenix 6mhz
2.Open dragonload exe
3.Select connect
4.Select program card en laad firmware predator x.xx
5.after programming "card loaded" appears

Flash repair

1.open software **********
2.select avr 90s8515
3.click on the first load on toolbar
4.load fun7ldr.hex
5.Select write use mode 4


Success
Parker
 
C

costa46

Programming Dragon 4.1 with Infinity USB Unlimited Programmer

I couldn’t get the Infinity Unlimited Programmer to work with the usual Dragonloader.exe files. Therefore had to use the software provided with the programmer. Very easy to use when you know how.

Check which card loader you have as the programming is different depending on your card. Cards will be printed with a label. If it says “F84A” it is a PIC card. If it says "FUN" then it is a FUN card. The loader file for the Fun7 is included in the Predator folder as FUN7LDR. The PIC loader, LOAD2MB, is not usually included in the Predator folder. A version can be found as part of the “Dragon CAM-Help-Files.zip.”.

If you have the Fun7 card:

1. Load FUN7LDR.hex into the flash area i.e. against the box labelled PIC
2. Load the xxx.dra file into ext EEprom, select [2] Reverse Span when asked
3. When done the window will look like this:

PIC: FUN7LDR.hex
Int. EEprom: Empty
Ext. EEprom: <Data from Ext. EEprom-file>
Ext. EEprom2: .dra

4. Press “write” and sit back as the card is programmed

If you have the PIC16F84A card:
1. Load LOAD2MB.hex into the flash area i.e. against the box labelled PIC
2. Load xxx.dra file into ext EEprom, select [2] Reverse Span when asked
3. When done the window will look like this:

PIC: LOAD2MB.hex
Ext. EEprom: <Data from Ext. EEprom-file>
Ext. EEprom2: .dra

4. Press “write” and sit back as the card is programmed

When the programmer is finished it is then the normal method of loading the card into the Dragon CAM and the receiver.
 
C

costa46

programming a dragon Fun7 loader card with the cas2 and its add-on:- or cas3


there are two type of dragonloader cards.
The first one is a pic based card (PIC16F84A).
The second one, is just a Fun7 (2x24LC1024) and it is marked as Fun7.
As an alternative, a standard Fun7 can be used as a dragonloader card.

1. start the cas2 / cas3 Soft -->
cas2 > you now you are in the main-menu.
cas3 > select Smartcard from top menu.
2. click the button "PROG"
3. put the Fun7 into the cardreader
4. choose the type "Prussian 5"
5. click the button erase and wait until the card is completely erased
6. click the button on the right side "Repair Dragon Card Loader"
....and wait until the loader will be written to the card
8. now you can close this window and you are back in the main-menu again
9.click the button "DRAGON" --> a new window opens and the message "Dragon Card Loader detected / recognized"
10.click the folder-icon and navigate to the required *.dra-file
11.click the button "Write to Dragon Loader Card" and wait for "Dragon Card programmed."

Congratulation your Dragonloadercard is written successfully

Now put it into your Dragon-Cam to upgrade the Predator.

original by echelon
modified by spider
 
C

costa46

Programming Dragoncam / T-rex using dummy card.

connect one end of 20pin ribbon cable to cas3
and the other end to dummy card.
insert Dragoncam into pcmcia slot of cas3
and insert dummy card into dragoncam slot (contacts facing up)
insert usb cable, and start cis software.
click cam module, then other cams, then Dragoncam.
select cam version, either ( 2.x ) or ( 3.x - 4.x )
click file name [...] and navigate to required *.dra
a new window opens...(common interface host)
select Dragonload. then click the Enter Selected button
select "Yes, Load Module", then Enter Selected button.
dragoncam will now be loaded with selected file.
a progress monitor will be shown in dragoncam loader window.
wait for loader successful, then remove cam.

c/o SPIDER

thanks m8
 
C

costa46

--------------------------------------------------------------------------------

Q:- updating dragon with cas3 and dummy card

-------------------------------------------------------------------------

did i read a post from someone who said they could update the dragon using the dummy card?
my loader card wont take any files, have tried reprogramming it but still no difference. can anybody help?

theblueirish

__________________________________________________ _____

ANSWER:-

TEZAK:-

There you go mate I hade it somwhere


connect one end of 20pin ribbon cable to cas3
and the other end to dummy card.
insert Dragoncam into pcmcia slot of cas3
and insert dummy card into dragoncam slot (contacts facing up)
insert usb cable, and start cis software.
click cam module, then other cams, then Dragoncam.
select cam version, either ( 2.x ) or ( 3.x - 4.x )
click file name [...] and navigate to required *.dra
a new window opens...(common interface host)
select Dragonload. then click the Enter Selected button
select "Yes, Load Module", then Enter Selected button.
dragoncam will now be loaded with selected file.
a progress monitor will be shown in dragoncam loader window.
wait for loader successful, then remove cam.

you can insert your loader card or a fun 7 card if not recognised as dragon loader in cas, first do a repair. CAS will write the flash and your loader will be repaired. Now go back and choose dra and write to card
 
Status
Not open for further replies.
Top