How To for DM 800 HD

B

boxgot

How to flash your Dreambox DM800 PVR

How to flash your Dreambox DM800 PVR
Flashing a new firmware (image) by Browser
 
K

k@lkov

Super VIP
Messages
10,003
How to flash your Dreambox DM800 PVR

How to flashing a new firmware DM800 with browser
Thanks Olmi
 
K

k@lkov

Super VIP
Messages
10,003
Temperature measurement and installation ventilator

By BEBI.
 
Last edited:
S

sugarnspice

Registered
Messages
354
How to install a fan in your DM800 by M.D

How to install a fan in your DM800


Firstly you need to take the USB cable and use wire strippers to get to the center wiring, you will get through a
layer of silver wiring and then you'll see 4
different coloured wires: White, Green, Red,
and Black.

You can hack the green and white one's off if theyre in your way.

You only need the red and black ones for power
(the others are for data).

Now you atach the black wire which is comming from the USB cable with the black wire from the fan cable,
and also do the same for the red with the red by snipping abit of the rubber off the ends and then twisting the wires together.

Then you will need to put some tape round them so they dont touch each other and so they stay seperate.
When all done, you can put some tape round over them all to make it look a single tidy cable as shown in the pic.
Normaly on a pc fan you would get a black and red wire to make it easy for you to know which is which, but in my case i had to find out which is which as i had three silver wires ;) lol.
The usb connection is located under the hard drive bay.
My fan lights up in a nice blue colour now, when switched on.

Enjoy... :D ​
 
B

boxgot

How do I get to Bios [DM 800 HD PVR]

How do I get to Bios [DM 800 HD PVR]

! ! ! The box must be connected to a DHCP server hang! ! !

1st First,shut down the box and disconnect from the network (min 1 minute)

2ndpress Power button on the front page and plug the box .

3rd The display xxx.xxx.xxx.xxx DHCP (IP address) *** *** STOP

4th In the Window's on Start -> Run -> go and telnet
followed by the box IP. (z.b. telnet 192.168.2.105) per
of network configuration

Now appears the bios of the box.

Here are pictures Bios
Click to expand...
 
Last edited:
S

sonic67

Registered
Messages
208
Use This ( Very Easy ) :

j8pquo.jpg


2dw6x46.jpg


1ruioh.jpg


2lia2h0.jpg


2d9p94j.jpg
 
B

Brummie

Staff member
Administrator
Messages
5,794
if i paid £359 for a receiver, if it being a dreambox or another receiver i would not want to be seeing these how to fit a fan to get it running smoothly.
 
E

elgeneral

Registered
Messages
7,811
Backup and restore settings from Enigma2

Backup and restore settings from Enigma2



Description:
It explains how you SadButTrue in boxing Enigma2 settings easily via an image update can be saved!

This applies to the DM7025 and DM800!

The OSD - Shots correspond to a DM7025 is here but the menu similar to the DM800.

Thanks to SadButTrue
 
L

lolazoca

Registered
Messages
704
How to install CCcam on Gemini Image (for Dreambox800)

How to install CCcam on Gemini Image (for Dreambox800)
 
B

Brummie

Staff member
Administrator
Messages
5,794
Setting up a DM800 none usals

a little howto hope it can help a few of you out.
 
B

Brummie

Staff member
Administrator
Messages
5,794
Barryallen how to

Barryallen how to

thanks to Ferret for the telnet commands and the first part of the how to.
 
L

lolazoca

Registered
Messages
704
How to change the boot image?

How to change the boot image?

hi,
i want to change the boot image

i have nabilosat BH v0.11 (BL69) in flash on dreambox800 HD and trying to find the file named "bild " in
/root/platform/kernel/bild
but noway to find it
can someone help me?
thks.

ps: here"s the tuto

Creating your own Dreambox Boot Logo


How to create your own startup, shutdown, radio, scan and mp3 logos

The dimension of these pictures must be 720×576 pixels in PAL format.
Path where the boot image is stored is /root/platform/kernel and is called bild.
Path where the other pictures are stored is /var/tuxbox/config/enigma/pictures.

The program we will use to create the pictures is called TMPGEnc.
Download TMPGEnc from official site
Unzip the file to your chosen destination.
Double click the ‘TPMGEnc.exe MPEG Encoder’ file and click ‘OK’ on the small pop up window. Then click ‘Cancel’ on the ‘Project Wizard (1/5)’ window that appears.
Next screen, bottom right…’Stream type’, check the box ‘ES (Video only)’.
Next, bottom left…’Video source:’ click on ‘Browse’ and select the background/photo that you want as your new logo.
Next, bottom left… ‘Output file name:’ click on browse and choose the path for your finished ‘new’ boot background/photo and edit the name to ‘bild’ (minus the ‘….’ and in lower case) ie: the line that apperars in the ‘Output file name:’ should read similar to C:\Documents and Settings\Whatever\My Documents\bild ( the actual name of the photo does NOT appear).
Next, bottom right…click on ‘Setting’ and check that the value settings are:

…..’Stream type:’ = MPEG-1 Video
…..’Size’ = 720 x576 pixels
…..’Aspect ratio:’ = 1:1 (VGA)
…..’Frame rate:’ = 25 fps
…..’Rate control mode:’ = Constant bitrate (CBR)
…..’Bitrate:’ = 12000
…..’Motion search precision:’ = Normal

When checked, click ‘OK’ to exit the screen.

Top left click ‘Start’, if all is goes well, the ‘100%’ bar appears and your completed ‘bild’ file is in your chosen ‘Output…’ location.

*** If You want to change the boot picture before compressing the image (after the ‘make rebuild-flash’ command ) , just copy it into /tuxbox-cvs/root/cdkflash/boot/root/platform/kernel before executing the ‘make flash-compress’ command.
Click to expand...
:thum:
 
You must log in or register to reply here.
Top