vu+ solo 2 time bomb bricked jtag problem

[starfox1]

Hi
i have vu + solo 2 time bomb bricked receiver trying to recover with j tag BBS cypress device i have j tag flash file downloaded from vu-hd.com installed broadband studio 3 and bcm 97346 after that successfully connected to samsung flash K9F2G08U0C and also downloaded flash file 100% but still only light on front pannel no usb port working.
one thing i have noticed that when i flashed box with flash file and box unsuccessful for start and i am trying to connect with broadband 3 bcm it was connected but when trying to connect with flash K9F2G08U0C it shows i/o error and couldnot detect flash after that many time i pressed refresh button some time 7 some time 8 and some time 6 then it was detect flash after that i was perform erase entire flash then easily it will detect the flash ic i could not under stand what is this i think boot loader is wrong for this box
The Chip is K9F2G08U0C and the board is Lonrisun.

[Blade]

Try this bootloader mate.

But that input output error could mean the nand is write protected or faulty.

[starfox1]

Originally Posted by Ferret

Try this bootloader mate.

But that input output error could mean the nand is write protected or faulty.

I tried yhe attached file with no luck.
now two case:
first if the nand is write protected is their a way to remove the protection? if the answer is no:
and the nand is faulty can i replace it with empty one and reflash with the same bootloader?

thanx in advance Ferret

[Blade]

Originally Posted by starfox1

I tried yhe attached file with no luck.
now two case:
first if the nand is write protected is their a way to remove the protection? if the answer is no:
and the nand is faulty can i replace it with empty one and reflash with the same bootloader?

thanx in advance Ferret

Ask your supplier to supply you with the correct bootloader they should know your not the first with this problem. Make sure your selecting the correct flash device to flash the bootloader to do this look at the nand chip and write down the ference use this in BB3

If that does not work there is a problem with the nand and it needs replacing.

[Blade]

Ive just fond this info else where by Aliraza63 try this with the attached files.

I have used the method according to instruction and luckly recoverd back my Solo 2 and my Friends Solo2 Se . Both boxes are working fine For other members I m pasting pics and Files set for the forum.

1. First of All Install Mcu_ Flash file With the RS-232 Cable from the folder
2. Switch off the Receiver
3. Open Hyper terminal
4. According to PDF guide Connect and load the boot laoder in this folder
5. After Successfull Complete Just Uplaod any Safe Image with Usb .

[starfox1]

Thank you i'll try this and feedback if that works !!

[kerrmuir]

Will this work for vu+ solo2 clone about a year old Nov 2013 ish

[darius1]

hey
is there any for vu solo?

[cifria]

I bought JTAG cypress and reloaded BOOTLOADER Lonrisun v4, but I still have the same problem with the tuner.
I have a new bootloader for Lonrisum but a .dat (is to come out with a fix for the tuner to be sent via HyperTerminal serial).
I have to load it using JTAG but having .dat extension decoder does not boot and I had to put the bootloader v4.
How can I convert the bootloader .dat to .bin?

[Talks]

Originally Posted by cifria

I bought JTAG cypress and reloaded BOOTLOADER Lonrisun v4, but I still have the same problem with the tuner.
I have a new bootloader for Lonrisum but a .dat (is to come out with a fix for the tuner to be sent via HyperTerminal serial).
I have to load it using JTAG but having .dat extension decoder does not boot and I had to put the bootloader v4.
How can I convert the bootloader .dat to .bin?

Hi cifria.
I have found this and it may help you to convert,
do a google serch with this name,
shc-3.8.6.tgz download
Regards Talks.