SCT - Strong Connection Tool 1.0

Here can you testing with you Receivers.
This is a tool e.g. SBCL. You can communication with plugins e.g. vplug to you Receiver.

Functioning
-------------------------------------
HOW IT WORKS SCT
-------------------------------------
1. Connect the receiver via the serial port to the PC.
2. Starting SCT.exe
3. On SCT Select the COM port connection.
4. Turn the channel decoder on a FREE To Air or position on a
These
5. SCT Press on the button ConnecT you will see in the window at the bottom of the log
Communications
6. The Plugins enable you want to use using the monitor (if not
You see the monitor menu | + select Options Show Plugins Area
7. You change channels using the remote control to the receiver that real
The virtual creation.

-----------------------------------------
Operation Technical SCT
-----------------------------------------
The receiver is enabled by SCT to send a series of data between these we
ECM flow and EMM.
Regarding the ECM are sent automatically to every change
Channel and are managed by SCT in each mode (remember the setting of
Receiver set in the panel | SETTINGS RS232 ---> ECM OUT)
Regarding the EMM however, as the flow of data is enormous and
Impossible to transmit in real time, we decided:
1. To filter the flow EMM according to the provider and based on the setting of vplug
(See v_emm.ini)
2. To enable the transmission manually flow through ozione in
Tab | REMOTE | Remote Option ---> Ams Out (enables flow)
We recommend to disable this feature when the flow is used by
Vplug to avoid impallamenti the receiver or system.

-------------------------------------------------- ---
COMPATIBILITY OF SCT WITH FIRMWARE
-------------------------------------------------- ---
Currently SCT is only compatible with the firm for Revolution 3 SCT strong.
The series SatTracker is not compatible, as the previous releases of revolution.
We have deliberately left in the SCT communication protocols of serial
For philips receiver models and pioneer. We never tested on SCT
These receiver, but can not exclude that operate cmq

--------------------------------------------------
COMPATIBILITY OF SCT PLUGINS WITH
--------------------------------------------------
SCT is fully compatible with Vplug and WinCSC. Regarding other
Plugins are yet to be tested or problems in communication
Data.

HOW CARICARE I PLUGINS
To load plugins simply put the plugin files into the directory
MDPLUGINS you find in SCT

-------------------------------------
Settings on the decoder
-------------------------------------
These settings are valid only on the firmware of the Revolution series SCT.
Go menu and the panel | Settings RS232 put
The following options:
- Dly1 = 5
- Dly2 = 2
Tis ECM-Out (for users who have other deco ECM out Philips or ECM Out
Pioneer)
- Rs232 = ON
RS-baud rate = 4800 bps
- Apid = No
And yet, enable the bandeau (+ key on the channel) enter into options (B button
And 3) and put AutoPid = YES and AeS CHK = NO

-----------------------------------
Settings on SCT
-----------------------------------
MAIN ------- --- Panel
Remember to select Check Box in the ECM PID correct channel. Usually
This is identified by the system automatically, but if this is not the case
Then select it manually.
Use the key RESTART note that if the exchange rate channel is not written
Log information on the new channel

REMOTE Panel --- ------
In DECODER REMOTE OPTION selected INTERNAL AU. Select EMM
OUT only allow sending of the EMM plugins.
In ECM OUT OPTION left AutoPid = One Time
In WAIT DWs put First ECM = 5 and Next ECM = 2

Panel --- ----- OPTION
--> Communication
TIS-Mode Select (who use the pioneer / philips must use other systems)
Input Buffer = 2536
Timeout = -1
Wait ECM (x philips only mode) = 135

--> Log
Settate as better believe for your needs.

--> Plugins
Packet Size = 184
Fake ECM = send on FTA
Send DWs = odd or even and select DWs checksum (although using
Vplug not need)
Ams (vplug) = selected
Set to 00 via Prov selected =
Add 00 to prefix = selected --> = selected if necessary
Packet Filter = FF
TDT = selected
GMT Offset = -2
Delay = EN 300468 --> in = 300 sec slide.

--> Decoder
Select all fields
Regarding AutoChange to Channel with AU year if it is checked
You have to enter the channel number corresponding to your list channels
Contains the channel that sends data for the AU

--> Other
Select all fields

Click to expand...