Installations Utility Enigma 1-2 for IPBox

Status
Not open for further replies.

juli13

Staff member
Administrator
Messages
10,194
For the flash memory or external hard drive

Preface: Since there are program changes frequently as descriptions of some warnings:
* This is OK now, instead of a period "." displayed.
* The implementation of the "long" command in the third box, the color remains red when you work - it will turn green.


***********************

Everything is explained step by step:

/ Configuration / setup /

1) Choose their profile:

At different firmwares - there are different passwords. Therefore, the presets (pre-configuration).

You can edit the password in the program and save it in the ini file.

Write the same IP address as the recipient. Is stored in the ini file.

2) Click on the button <Connect telnet> (Connect via Telnet)

If everything is configured correctly, all 3 red rectangles are green.

Excerpt from the log:
CODE connect to 192.168.1.4
..
Disk / dev / sda: 320.0 GB, 320072933376 bytes
Disk / dev / sdb: 1967 MB, 1967128576 bytes
.

If the third field is not switched on the green, then the password is either incorrect or non-standard invitation.
Press <Test> to receive the latest posts from the receiver.
Copy the log on the forum, stating the model receiver firmware version.

/ Formatting / FORMAT /

3) Select the Device --

Do not forget to save on "Settings" receiver via Bookmark Backup
then press the button on the next 1 to 2 - 3 - 4

1. umount. It is) necessary in the use of flash drives (or drive.
After successful Unmounting an OK is to see if they fail - an error message. You see the log
2. fdisk. This will delete all marked up with the disk and creates a new or multiple partitions.
Do not divide könnendie hard disk if the partition where you want to install Linux firmware format is referred to as "active".
3. format. In preparation for the file system. Does it have to do by the recipient. Only in this way is guaranteed by downloading firmware.
4. Embed mount (). Connect the device to the system receiver and mounted folder. (4. pryamouglnik green).

Log excerpt:
CODE fdisk / dev / sdb. . . . . . . . . . . . . .
Fdisk is ok
Ok
Writing inode tables: 0 / 15 ????? 1 / 15 ?????
........
/ Installation / Install /

Last necessary operations:

1. open e2. Select the firmware archive (tar or gz is)
2. copy (copy). Copies will be supporting the firmware via FTP to the receiver (on the devices to). If the receiver depends on this operation, it is possible that if a new mount the partition is not formatted correctly. Try to repeat the process for including too.
3. unpack (unzip the firmware)
4. flash. Describes the internal receiver firmware or the multi-boot.
To do that, they invite dasDatei.img into the receiver and press this button.
This function is update.sh controlled by the script to work with the Sif, NLB and UFM-enabling modifications.

Log excerpt:
QUELLTEXTFile: Ip-Box-AAF-RisingSun 9000HD.tar.gz
Connecting to 192.168.1.4:21
C: \ SAT \ Enigma \ Ip-Box-AAF-RisingSun 9000HD.tar.gz write ...
Successful Transfer. File is C: \ SAT \ Enigma \ Ip-Box-AAF-RisingSun 9000HD.tar.gz.
.

The process of Endpackens (and more) can take a very long time.

/ E2 /

In this area you can customize the network settings, and equipment.

1.correct ip (IP change) - fixed settings for the network. Installs IP (which is used for communication with the receiver configured), name server
2. correct (adjust fstab fstab) - corrects the settings for the system partition on the hard drive.
The settings are written to the hard disk or installed into the Flash (sda1 = swap,) sda2 = HDD;

/ Backup / backup /

In this section you can save your own receiver settings before you upgrade your version of the Enigma.
To save the files in the folder / var / config (2 units) and / usr/local/share/enigma2 (there are standard, channel lists, settings, etc. are stored)
DISEqC These settings are for Enigma2 (ISCAN Mod) and partly also valid for the AAF Enigma2. (Do not save the settings for network balloons??)

1. backup - save your settings into an archive. (backup.tar.gz the file is saved in the folder with the program (Enigma Setup).
2. restore - restore the settings from the archive.

Optionally, you can also use the settings of the Softcam (Emu) from the directory store / var keys /.

Save and unzip the files on the receiver to click) <mount> (connection.
All files that are in its path to be restored.

Sudden loss:
If something does not work, it is best to either the program closing and reopen them and start again from scratch.
Or, if you understand what the case, continue with the steps that are not completely in the last session. But it is necessary to have a connection to the Telnet. If you only want to download firmware, you must first create a "mount".

Of course, you can not so soon after the start of the program immediately unpack.
If the file name is not known, etc. In general, if you have problems, perform the above steps again.
 
Status
Not open for further replies.
Top