[Help] x403p - Doesn't boot anymore after channel list update

genuineboy · Jan 5, 2012

I've installed the ps_lemontree_1.4.34.rar and it was working fine... until I forgot and I have uploaded the previous channel list done with 1.3.81 version.

Now the receiver doesn't boot anymore... it carry on rebooting itself... without showing anything on the screen. I can only see on the front the "on" coming and disappearing... What can I do?

regards

genuineboy · Jan 6, 2012

Fixed! Bought a null-modem cable and reflashed the rom.

Chejuli · Jul 6, 2012

Help x403p - Doesn't boot anymore after software update only shows 00:00 on front panel.

JAKITAKI · Jul 6, 2012

Chejuli said:
Help x403p - Doesn't boot anymore after software update only shows 00:00 on front panel.

upload software, via RS232 ,using the Upgrade Tool

Chejuli · Jul 6, 2012

JAKITAKI said:
upload software, via RS232 ,using the Upgrade Tool

upgrade tool is failing to connect via rs232. receiver is not coming on but pc detects using lan

JAKITAKI · Jul 6, 2012

Chejuli said:
upgrade tool is failing to connect via rs232. receiver is not coming on but pc detects using lan

must succeed, try to continue

Chejuli · Jul 6, 2012

I have been trying all day. Decoder is not communicating via rs232. I tried switching it on and off still only shows 00:00 does not even display on message

JAKITAKI · Jul 6, 2012

Chejuli said:
I have been trying all day. Decoder is not communicating via rs232. I tried switching it on and off still only shows 00:00 does not even display on message

try with another upgrade

Chejuli · Jul 6, 2012

JAKITAKI said:
try with another upgrade

This is what i get Open Serial Port..
Sync to serial port..
Target not connect or target is error status!

JAKITAKI · Jul 6, 2012

Chejuli said:
This is what i get Open Serial Port..
Sync to serial port..
Target not connect or target is error status!

do not use the files that you have given
and you are asking for help

make sure you have good nullmodem

Chejuli · Jul 6, 2012

Chejuli said:
This is what i get Open Serial Port..
Sync to serial port..
Target not connect or target is error status!

Is my orton dead?

Chejuli · Jul 7, 2012

JAKITAKI said:
do not use the files that you have given
and you are asking for help
make sure you have good nullmodem

I have tried 3 nullmodem cables with same results

Chejuli · Jul 8, 2012

Please how else can i revive this decoder?

DM9004K · Jul 10, 2012

my ortonx403p also in front panel 00:00 i tried lot of times but not sucess if any have a solution plz help

Chejuli · Jul 14, 2012

lonezahoor said:
my ortonx403p also in front panel 00:00 i tried lot of times but not sucess if any have a solution plz help

Has anyone assisted you yet. Mine still has the same problem. Please anyone with jtag for orton x403p.

lnbbeisser · Jul 14, 2012

i don`t know, if your usb works,

take a firmware , is ok, then write ZB XXXX. abs to XXXX.AUTO.
connect usb with reciver, start reciver and now your reciver update automatic.

sorry for my bad engl. is copy by Lothar Matheus

Chejuli · Jul 15, 2012

lnbbeisser said:
i don`t know, if your usb works,

take a firmware , is ok, then write ZB XXXX. abs to XXXX.AUTO.
connect usb with reciver, start reciver and now your reciver update automatic.

sorry for my bad engl. is copy by Lothar Matheus

Can this make the decoder to work again? Am not sure if the usb works

Chejuli · Jul 15, 2012

Can you please explain the procedure. The receiver is not detecting the usb

Chejuli · Aug 1, 2012

Please anyone to assist to make this receiver work again.

Chejuli · Aug 1, 2012

lonezahoor said:
my ortonx403p also in front panel 00:00 i tried lot of times but not sucess if any have a solution plz help

Has anyone managed to revive this receiver please?

[Help] x403p - Doesn't boot anymore after channel list update

Registered