Go Back   Sat Universe > Cams > Cam Files > X-cam

Note: Visitors from certain countries might see in-text advertising(underlind words in posts) or pop-under ads.
It is only shown to unregistered visitors or members that haven't made any posts. So you can easily get rid of it.

World-Of-Satellite

How To X-Cam

X-cam

Closed Thread
  #1  
Old 27-07-2007, 18:01  Translate from English to Italian  Translate from English to French  Translate from English to German  Translate from English to Spanish  Translate from English to Dutch  Translate from English to Greek  Translate from English to Portuguese  Translate from English to Russian  Translate from English to Russian
costa46
Guest
 
Posts: n/a
Thumbs up How To X-Cam

How To Program an XCam

Quote:
Downloading Main Program
1. Install and open the proggy Xcloader.
2. Select the download file and set the block item to Block2.
3. Press the connect buton.
4. Now go to your receiver and select Update item from CI menu.
5. Press “OK” to Activate loader
6. Wait until ‘Transfer Done!’ message on Xcloader program appears.
7. Shut off receiver even when it's not giving you the message it's finished.
8. Put on receiver, go into the CI-menu again, go to settings and select “default Key”.
9. Enjoy!
Quote:
Downloading new Key Table
1.Select the key table file(softcam.key) and set the block item to Block14.
2. Press Connect button, then the following message will pop-up:
3. Now go to your receiver and select Update item from CI menu.
4. Press “OK” key of to Activate loader
5. Wait until ‘Transfer Done!’ message on Xcloader program appears.
6. Shut off receiver even when it's not giving you the message it's finished.
7. Put on receiver, go into the CI-menu again, go to settings and select “default Key”.

Enjoy.
  #2  
Old 27-07-2007, 18:02  Translate from English to Italian  Translate from English to French  Translate from English to German  Translate from English to Spanish  Translate from English to Dutch  Translate from English to Greek  Translate from English to Portuguese  Translate from English to Russian  Translate from English to Russian
costa46
Guest
 
Posts: n/a
Default

A Useful procedure if something goes wrong with programming the CAM - It works:

Code:
Just in case of a possible not complete firmware updating you can have the followings malfunctions: 
- CAM shows an anomalous operation in “EMU” mode 
- If you insert an official card you have frequent freezing 
- Impossibility to program a new Firmware 

Then you can try the following procedure: 

1) Use a Decoder that powers the CAM also in Stand By 
2) Insert the CAM into the Decoder (switch off with remote (DO NOT POWER DOWN AT THE MAINS) 
3) Insert the serial programmer into your XCAM 
4) Switch-on the decoder and go to a FTA channel 
5) Verify the installed firmware (1.01 or 1.02 or 1.03T) 
6) On the PC start the X-Loader Program 

Now it’s where you have to trick your CAM. 
All of you is aware of the fact that in Block 2 you should write the Firmware and on Block 14 the softcam.key. 
In this case (and remember on in this case of anomalous CAM), you load the softcam.key in block 2 instead of block 14. 

7) Press Connect 
 Go to the CAM parameters 
9) Activate the loader 
10) The programming starts 
11) At the end of programming, do not exit from the program X-Loader !!!!! 
12) With the remote, verify the CAM parameter 
13) You should now read “XCAM Module” like a new virgin CAM!! 
14) Now you can load the new firmware in the X-Loader and program it in block 2 of your CAM 
15) Press connect (without doing anything in the CAM menu) and the firmware download will start automatically. 
16) At the end of download, switch off the decoder (not powered) and remove the programmer without removing the CAM from the decoder 
17) Switch on the decoder on the previously selected FTA channel 
1 Read CAM parameter to verify correct firmware updating
  #3  
Old 27-07-2007, 18:02  Translate from English to Italian  Translate from English to French  Translate from English to German  Translate from English to Spanish  Translate from English to Dutch  Translate from English to Greek  Translate from English to Portuguese  Translate from English to Russian  Translate from English to Russian
costa46
Guest
 
Posts: n/a
Default

KEY2HEX is a program to convert SOFTCAM.KEY files into HEX or BIN files
which can be used with a Funcard to update XCAM block 14.

Quote:
You will need firmware version 1.04 with Funcard support for this to work.


1. Download latest SOFTCAM.KEY from usual places.

2. Run KEY2HEX.EXE.

3. Select your preferred output format (HEX or BIN).

4. Use the browse (...) button to locate your SOFTCAM.KEY, or drag and
drop the file from Win Explorer.

5. If you use drag and drop the file will convert automatically,
otherwise click Convert.

6. Upload generated file into external EEPROM of a Funcard, and XCUP.HEX
into the flash of the card.

7. Tune your receiver to a FTA channel.

8. Insert the Funcard into the XCAM.

9. Select Update from the XCAM menu, and wait for it to finish.

10. Remove Funcard. Your XCAM is updated with the new SOFTCAM.KEY!
  #4  
Old 31-07-2007, 23:15  Translate from English to Italian  Translate from English to French  Translate from English to German  Translate from English to Spanish  Translate from English to Dutch  Translate from English to Greek  Translate from English to Portuguese  Translate from English to Russian  Translate from English to Russian
T24 T24 is offline
SatUniverse Friend
 
Join Date: Jul 2007
Posts: 2,035
Thanks: 50
Thanked 457 Times in 164 Posts
Country: Country Flag
Default Xcam PCMCIA guide

Xcam PCMCIA guide
Attached Files
File Type: zip xcam_pcmcia_guide.zip (121.5 KB, 452 views)
The Following 5 Users Say Thank You to T24 For This Useful Post:
forks (09-10-2008), manu4 (29-11-2007), merzali (13-09-2010), Rocknroll (24-02-2008), samer1970 (20-07-2008)
  #5  
Old 24-08-2007, 10:36  Translate from English to Italian  Translate from English to French  Translate from English to German  Translate from English to Spanish  Translate from English to Dutch  Translate from English to Greek  Translate from English to Portuguese  Translate from English to Russian  Translate from English to Russian
costa46
Guest
 
Posts: n/a
Default update your xcam by PCMCIA

here two driver that should help you with the update of the cam (Xcam version or Orion) by PCMCIA

Thanks Mefisto
Attached Files
File Type: rar ORION Pcmcia.rar (102.7 KB, 352 views)
File Type: rar XCAM ANGEL Pcmcia.rar (100.8 KB, 339 views)
The Following User Says Thank You to For This Useful Post:
Rocknroll (24-08-2007)
Closed Thread


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 13:52.


Powered by vBulletin
Copyright ©2006-2019 - Sat Universe