MGCAMD-server

otheitis

Registered
Messages
59
Hello i have the ab ipbox 9000hd.I have instaled the firmware from the sifteam with mgcamd and evocamd inside.But i can not be conected in server newcamd.I have put in the var/key the files mgcamd.cfg and the file newcamd.client but the mgcamd can not be conected in server newcamd.I do all the pass which i done in dreambox 500 but nothing.If someone has resolve this problem or has the corect file which i need and it is easy for him to help me.About the evocamd this can not start and can not decode with keys.Mgcamd can decode with keys.Please help me.i used the files mgcamd.cfg and newcamd.list from one version for dreambox.Because i can not find this file in image sifteeam.
sorry for my english.
 

Rocknroll

Staff member
Administrator
Messages
6,174
You've got all the files needed mgcamd.cfg and newcamd.client should be enough. You could turn on log to console in mgcamd.cfg and all debug options then run it on telnet to see if it gives you any clues.
 

Rocknroll

Staff member
Administrator
Messages
6,174
You can edit the file on your pc then ftp it to your box.
Or you could telnet to your box from windows command prompt. By typing: telnet boxip
Then editing config file with vi editor, using vi /path-to-file
Not sure if the image you are using even supports telnet, but I guess it should. It is still in early development stages though.
 

otheitis

Registered
Messages
59
i made the change in line G: for the newcamd cliend.But i am not sure if the other settings is ok.This is my mgcamd.cfg:



# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
U: { 01 }

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 00 }
 

Rocknroll

Staff member
Administrator
Messages
6,174
You could change this line:
# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 00 }

to P: { 02 }
 

mirg

Registered
Messages
144
You have to rename newcamd cliend to newcamd.list ! and than your line in newcamd.list should be!
CWS = dummy dummy 10001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
CWS = dummy dummy 10002 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
:thum:
 

otheitis

Registered
Messages
59
thank you very much!Now it works fine.i hope in future a cccam version to be ready for this power machine.
 

pjhavariotis

Registered
Messages
7
Hi. Can you please tell me which firmware from SifTeam you have installed? I am also facing some problems with mgcamd . . .
 

pjhavariotis

Registered
Messages
7
Can you please tell me a location in order to download it? Unfortunately the only version I can find is the 0.02.2 . . .
 
Top