4:2:2 decoders

[Solaris82]

It is possible to enjoy the 4:2:2 feed and 4:2:0 feed also with Amazon fire stick, Android box tv
through the "Dream Player android tv" application.
You have to change the video settings within the app by inserting the values until there is a smooth vision-

the fluidity of the vision is directly proportional to the type of device you are using

 

[Francescone]

It is possible to enjoy the 4:2:2 feed and 4:2:0 feed also with Amazon fire stick, Android box tv
through the "Dream Player android tv" application.
You have to change the video settings within the app by inserting the values until there is a smooth vision-

Using a good enigma2 receiver and AppleTV you can obtain a cristal clear 422 video.

 

[ddd111]

i have and use another way
you can check two picters

 

[kozz90]

where you enter values into the rx8200 to open biss feed channel?

 

[moonbase]

where you enter values into the rx8200 to open biss feed channel?

On screen menu in web browser

 

[kozz90]

Need more help I can't find it. Maybe a screenshot,I don't know how to do it, when I enter the value error message that it is too large.

 

[ArloG]

Kodi PVR has a very clean and organized GUI. 4:2:2 is seamless as well. Firestick/ Fire TV or Android smart TV.

 

[Francescone]

Need more help I can't find it. Maybe a screenshot,I don't know how to do it, when I enter the value error message that it is too large.

Please remember that biss keys are 12 digits long, not 16.
The 16 digits length is only for consumer receivers, but bytes 4 and 8 are only checksum for bytes 1+2+3 and bytes 5+6+7 respectively.
So, from all the keys you find here remove the digits 7-8 and 15-16.
For example, if you find this key:
11 22 33 AA 44 55 66 BB
In the RX8200 you must enter:
11 22 33 44 55 66
Hope this helps.

 

[kozz90]

I can't lock the channel on rx8200, are the configurations correct?

Configuration-RF#1
Parameters
LNB LO Frequency:9750.000 mhz
Satelite Frequency:10733.000 mhz
Symbol rate:34.000000 MSym/s
ModulationVB-S2 QPSK OR BPSK AUTO FEC
RollOff:20%
Spectrum Sense:AUTO
Search Made:MANUAL
Search Range:2500khz
LNB Power Op:ENABLE
LNB Power Level:13v (VERT)
LNB 22kHz: off



Inverto Pro Twin konwerter LNB C120


Eutelsat 10B @ 10.0°E
10733 - V - 34000 | 4:2:2
1920*1080 - DVB-S2 - 8PSK
ID: SUPPONOR GTX 1 (NOWY ID: TURQUIA 1)


Photo attachedConfiguration

 

[duaneclaude]

I can't lock the channel on rx8200, are the configurations correct?

Configuration-RF#1
Parameters
LNB LO Frequency:9750.000 mhz
Satelite Frequency:10733.000 mhz
Symbol rate:34.000000 MSym/s
ModulationVB-S2 QPSK OR BPSK AUTO FEC
RollOff:20%
Spectrum Sense:AUTO
Search Made:MANUAL
Search Range:2500khz
LNB Power Op:ENABLE
LNB Power Level:13v (VERT)
LNB 22kHz: off



Inverto Pro Twin konwerter LNB C120


Eutelsat 10B @ 10.0°E
10733 - V - 34000 | 4:2:2
1920*1080 - DVB-S2 - 8PSK
ID: SUPPONOR GTX 1 (NOWY ID: TURQUIA 1)


Photo attachedConfiguration

Could be signal strengh. Tuner in the rx 8200 isn't the most sensative.

 

[Francescone]

ModulationVB-S2 QPSK OR BPSK AUTO FEC
Is it BPSK or 8PSK? It must be 8PSK, otherwise your receiver is not licensed correctly.

Search Made:MANUAL
Search Range:2500khz
Increase the value to 5000KHz, it is better, partiularly if the LNB is not a professional one so the OL could drift a little bit.
All other parameters are OK, so if you do not lock probably the signal is too low. Which dish are you using?

 

[kozz90]

8psk.
Antena Gibertini OP150S 150cm
I have no problems blocking a channel on my pc or tv decoder. I just tried to block another channel on 7e.

 

[Francescone]

Did you choose the right input?
Remember that the RX8200 does permit to set the satellite parameters also when the input is set to ASI or a different RF input.
So check if the RF input does match the input you are working on.
Also check the RF input cable. Did you connected the right input? You have four connectors available.
Finally, try a different signal, maybe a strong one like on Hotbird or Astra.

 

[kozz90]

indeed the signal was too weak, today I finally blocked something, but video status: error.

 

[Francescone]

indeed the signal was too weak, today I finally blocked something, but video status: error.

It means that the biss key is wrong.
Did you entered the key from the front panel or remotely?
If remotely, typing errors can corrupt the key and it does not work, so keep attention when entering.

 

[kozz90]

I enter the biss key in the web menu tab in CA/biss (mode 1)

 

[Francescone]

I enter the biss key in the web menu tab in CA/biss (mode 1)

Yes this is correct. So, as I mentioned, keep attention when typing. If you make mistakes, reload the web page and try again.
Also, I suggest you to test the news feeds at 7 East, where the key is certainly valid and easy to find. Check the biss feed keys section here at SU.

 

[moonbase]

I do not make mistakes entering the code. Eaven CA service status is on green "service authorized. the problem is something else.

Possibly a configuration setting or a drop down option in the RX8200 menus.
Try looking at what Service ID options there are, if it is a multi channel mux the biss key might only work on one channel of the mux.

 

[Francescone]

Also, how you set the Service lock mode? I suggest you to use the Hunting mode, so you always have pictures as soon as the receiver locks the channel (obviously if the channel is FTA or the right biss key is entered).

 

[kozz90]

Thanks a lot, I solved the problem, I was removing the wrong characters in the biss key. You guys are the best.