A mundet dikush te me ndihmoje me dm800hd pvr,kam bere nji flash me imazh te gabuar dhe ne display me shkruan error! look at www.dm7020.com *ERR01: NO CA FOUND
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
error! look at www.dm7020.com *ERR01: NO CA FOUND
- Thread starter adush
- Start date
look heree hapa aparatin dhe shikova per Sim kard dhe ajo eshte e-star SIM V3.0 me ndihmoni ju letem
http://www.e-star-sim.com/en/down-sim800.php
this page is for DM800,if you have DM800se go to the other page at the top
e provova me dreamup dhe asgje kuadrati ku shkruan flash nuk aktivizohet qe mund ta shtypi per te bere flashin
Nqs nuk te aktivizohet dmth qe nuk eshte lidhe kavo rs232-to usb me Pc,duhet me pare te kesh shkarkuar driverat e kavos ne pc dhe pastaj beji kontroll portes Com te kompjuterit dhe gje porten e sakte
adush, NCF-Sim3-v2.5, shikoje njehere se mos e shkarkon kete fail, me pas ju do tju duhet qe aparatin tuaj ta lidhni me rs232 dhe me internet, deri ketu per momentin po ju shpjegoj sepse eshte nje procedure pak e veshtire po nuk i ke para sysh gjerat, po munde shkarkoje kete fail dhe mbase neser flasim prap nese do ta kem te mundur, ju pershendes.
Dreambox NO CA FOUND Repair Tool NCF SIM2 v3.0
Update Features :
-SIM2 SSL Support Updated
-Added DM800SE SSL#84d Support
-Added DM800SE SSL#84c Support
-Added DM500HD SSL#84d Support
-Added DM800HD SSL#84d Support
-Added Silicon Labs CP210x USB to UART Bridge Smart Detection : [Hot & Exclusive For SIM2 Users Support]
[Users Don't need anymore to check the correct port from the device manager]
-Added Silicon Labs CP210x USB to UART Bridge Audio Notification Connected/Disconnected (Exclusive FOR PEOPLE WITH SPECIAL NEEDS)
-Added Network Domain Range Check & Crossover Cable Notification
-Added Wrong SSL Device Type Notification
-Added New Interface Skin
-Software Interface Rebuilded
flashing:
0 Install Driver (USB to serial adapter if used)
1 Connect powered off box with a null modem cable to the PC and via a network cable to the router (DHCP enabled)
2 Sunray Flashup start and make sure that you selected the correct COM port
3 Activate "repair defects sectors" under Tools
4 enable Network
5 Enter the IP of the PC and the Box
6 press Connect
7 Switch box and the flash loader is transferred to the box
8 If the flash loader has been successfully transmitted, an IP should appear in the display
9 Then, as usual flash by Internet Explorer:
e shkarkon ketu
Update Features :
-SIM2 SSL Support Updated
-Added DM800SE SSL#84d Support
-Added DM800SE SSL#84c Support
-Added DM500HD SSL#84d Support
-Added DM800HD SSL#84d Support
-Added Silicon Labs CP210x USB to UART Bridge Smart Detection : [Hot & Exclusive For SIM2 Users Support]
[Users Don't need anymore to check the correct port from the device manager]
-Added Silicon Labs CP210x USB to UART Bridge Audio Notification Connected/Disconnected (Exclusive FOR PEOPLE WITH SPECIAL NEEDS)
-Added Network Domain Range Check & Crossover Cable Notification
-Added Wrong SSL Device Type Notification
-Added New Interface Skin
-Software Interface Rebuilded
flashing:
0 Install Driver (USB to serial adapter if used)
1 Connect powered off box with a null modem cable to the PC and via a network cable to the router (DHCP enabled)
2 Sunray Flashup start and make sure that you selected the correct COM port
3 Activate "repair defects sectors" under Tools
4 enable Network
5 Enter the IP of the PC and the Box
6 press Connect
7 Switch box and the flash loader is transferred to the box
8 If the flash loader has been successfully transmitted, an IP should appear in the display
9 Then, as usual flash by Internet Explorer:
e shkarkon ketu
O mik,nuk eshte SIM2 por estar-sim, prandaj mos e ngaterro me nje dreamup qe nuk i sherben.Zgjidhja e vetme eshte ajo e ofruar nga Brummie me lart.Shoku ti nuk ke ber asnje perpjekje sepse po te lozje pak do te kishe bere dicka.
shikoje kete sesi behet
NCF Tool - YouTube
Last edited:
e provoj me optiflasher dhe i bej te gjitha hapat per ta lidhur me aparatin,por ne momentin qe klikoj te estar sim per te vendosur cfar ssl te instaloj aty tregon vetem per dm800se e jo per dm800hd,gjithsesi e provoj te shkarkoj kyt ssl dhe klikoj start ne momentin kur ndezi aparatin tregon aparati eshte lidhur por me pas shkruan Wrong Boot Response,,,kush e di se si mund ta perdor kyt program per aparatin tim ju lutem me estar sim3,sepse kam lexuar se me kyt program mundem te kthej aparatin ne gjendje pune