Instructions for program the card 12/07/07 with latest current sources
Hope this thread will help all new users
We know this thread is little delay but even till now this card keep getting new users
***DO NOT use the Gamma card option in cas 3 smart cards section of the cas 3***
This Guide are only for loaders:
Version
1.0
1.1
2.2
>For Sh*wtime loader V 1.1 needed to continue getting updates
versions 1.0 & 2.2 was only mainly use for add/show, but is not advised any longer the use for it(all thought will not damage ur card).
>for Eur* 1080 HD & N*va mainly loader V 1.0
can be use V 1.1 as well with no harm for the card
in fact seems to be an update
i don't have more infos about it right now sorry.
#You will need install in ur pc or laptop, Microsoft NET FRAME WORKS at l east version 2.0, available from Microsoft web.
#A straight serial cable 9 pin with the correct ends needed
Please follow this steps in the order i m suggesting:
1. Open cas 3 by click the icon on your desktop
2. connect the usb cable, wait till program starts
3. go to utilities tab
4. click the phoenix mode
5. choice 3.579 mhz usually for pc, or 6 mhz for laptop
6. hide button
7. open the needed loader with glasses by double click it
8. in the loader window when opens correct the settings in com port,
tick the 6 mhz button only if need it, load the latest file where u saved
it.
9. Insert your card chip down & connect the serial cable
10. now click program
Shortly u will see the message "card program successfully"
That's it!!!
Take out card & plug it in your stb / cam & wait ti AU.
Sometimes some small tips need to be done for faster AU:
Go to the transponder that you think it may AU better, switch on / off your stb, flick channels up / down, take card out ot the cam stb slot etc
-----------------------------------------------------------------
NOTE
If you see the message NO ATR then go to step 5 & change the mhz.
Is good advise as well to check your serial cable if is been connected well!
-----------------------------------------------------------------
Similar process is for cas 2, dynamite
both is been confirm working 100% but will need additional ADD ON
ENJOY YOUR CARD
i must mention, in my opinion this card is from the best ever made so the BEST out as quality & as choices of few files
Eur* 1080
Multi ch*ice
A*d
Sh*wtime
N*va
N*va cy
Orb*t
S*xview
M*t
C*nal plus
Tv Vl*anderen
P*ink Plus
B*ltsat
THANKS TO GAMMA TEAM
HAVE FUN,regards fevgatos
Hope this thread will help all new users
We know this thread is little delay but even till now this card keep getting new users
***DO NOT use the Gamma card option in cas 3 smart cards section of the cas 3***
This Guide are only for loaders:
Version
1.0
1.1
2.2
>For Sh*wtime loader V 1.1 needed to continue getting updates
versions 1.0 & 2.2 was only mainly use for add/show, but is not advised any longer the use for it(all thought will not damage ur card).
>for Eur* 1080 HD & N*va mainly loader V 1.0
can be use V 1.1 as well with no harm for the card
in fact seems to be an update
i don't have more infos about it right now sorry.
#You will need install in ur pc or laptop, Microsoft NET FRAME WORKS at l east version 2.0, available from Microsoft web.
#A straight serial cable 9 pin with the correct ends needed
Please follow this steps in the order i m suggesting:
1. Open cas 3 by click the icon on your desktop
2. connect the usb cable, wait till program starts
3. go to utilities tab
4. click the phoenix mode
5. choice 3.579 mhz usually for pc, or 6 mhz for laptop
6. hide button
7. open the needed loader with glasses by double click it
8. in the loader window when opens correct the settings in com port,
tick the 6 mhz button only if need it, load the latest file where u saved
it.
9. Insert your card chip down & connect the serial cable
10. now click program
Shortly u will see the message "card program successfully"
That's it!!!
Take out card & plug it in your stb / cam & wait ti AU.
Sometimes some small tips need to be done for faster AU:
Go to the transponder that you think it may AU better, switch on / off your stb, flick channels up / down, take card out ot the cam stb slot etc
-----------------------------------------------------------------
NOTE
If you see the message NO ATR then go to step 5 & change the mhz.
Is good advise as well to check your serial cable if is been connected well!
-----------------------------------------------------------------
Similar process is for cas 2, dynamite
both is been confirm working 100% but will need additional ADD ON
ENJOY YOUR CARD
i must mention, in my opinion this card is from the best ever made so the BEST out as quality & as choices of few files
Eur* 1080
Multi ch*ice
A*d
Sh*wtime
N*va
N*va cy
Orb*t
S*xview
M*t
C*nal plus
Tv Vl*anderen
P*ink Plus
B*ltsat
THANKS TO GAMMA TEAM
HAVE FUN,regards fevgatos