Incubus Discussion

Bro1

Registered
Messages
278
whats are the changes in the new version ??

are they the same as the one for Revo/mini
 

xxxAxxx

Super VIP
Messages
1,172
pls look at the readme file....change log is there and very clear....or read @elgeneral post...
 

goofyboy1

Registered
Messages
7
hello,

i've installed nlb 8833 beta.
But incubus is not very good. i'm connect to a ccCam server but it well take a long time to get the key.
And not ever canal is in the list.

I use an ipbox 9000 hd

greetings
 

valerica

Registered
Messages
55
Incubus v.0.70

The archive doesn't contain the .sigma version .
Can anyone upload it ?
Thanx .

Cheers ,
Val.
 

sisi1380

Registered
Messages
50
Hi
Is there any changes in config. file in 0.7
could you attach it?
somebody said it does not work with sifteam? I think it could be for changes in conf. or prio.
is there any comment to resolve it?
regards
 

milanbota

Registered
Messages
28
the conf file is a little changed.
it works with sifteam

Code:
##############################################################################
# incubusCamd configuration file                                             #
# All configuration options in this file observe the same format:            #
#     <configuration_name>=<configuration_value>                             #
#                                                                            #
# Each section are [<section_name>:<option_1>:<option_x>] like.              #
#                                                                            #
# No matter about white spaces on any place or UNIX/DOS style files          #
##############################################################################

########################### general configuration ############################
[General]
# Enable (1) or disable (0) background execution
# 0 - Off
# 1 - On
background_execution=1

# This sets the level of console output for debugging:
# 0 - No debug messages, 1 - First level debug messages, 2 - Second level debug messages,
# 3 - Print all debug messages
debug_level=3

# This option enables (1) or disables (0) the writing of debug information to the
# console.
log_to_console=1

# This option enables (1) or disables (0) the writing of console output to a log file
log_to_file=0

# When log_to_file is set to 1, this is the path and filename to write console
# ouput to.
logfile_name=/var/bin/camd.log

# Used to activate on-screen messages. Username and password required if
# HTTP authentication is enabled on enigma.
on_screen_messages_show=1
on_screen_messages_username=root
on_screen_messages_password=
on_screen_messages_key_update=1
on_screen_messages_wait_for_key_update=0
on_screen_messages_ecm=0
on_screen_messages_emm=0

#When activated, camd will listen on the specified port for connections. All
#log activity will be broadcast in real-time to connected clients.
console_logs_broadcast=1
console_logs_broadcast_port=666

############################ caid configuration ##############################
#
# First of all the cam use the incubusCamd.prio file, then use the 
# configuration below.
# Sections are defined by the value of the CaID.
# You can choose the default ecm table used by the codify, this means that
# you can choose the first byte of the raw ecm that is downloaded from sat.
# If you don't know what value to insert, use "80". (all value are in hex)
# Default value for ecm_table is 0x80.
# The option "priority" tells if one caid should be selected before try
# another one with a priority value greater.
# The less is the value the greatest is the priority. Choose from "0" to any value,
# priority value is decimal.
#

[CaID:0100]
ecm_table=80
priority=1

[CaID:0500]
ecm_table=80
priority=1

[CaID:0600]
ecm_table=80
priority=1

[CaID:0919]
ecm_table=80
priority=1

[CaID:093B]
ecm_table=80
priority=1

[CaID:0B00]
ecm_table=80
priority=1

[CaID:0D00]
ecm_table=80
priority=1

[CaID:1700]
ecm_table=80
priority=1

[CaID:1800]
ecm_table=80
priority=1

[CaID:2600]
ecm_table=80
priority=1

########################### provider configuration ###########################
#
# All parameters are in hexadecimal notation.
# Each section is defined by the provider id value.
# If you don't know the provider id value then use the provider id "000000" and ca id "0000".
# On provider 000000 caid 0000 goes all provider wich are not declared. If the provider
# is declared then the cam will use the provider founded.
#

[Prov:000501:CaID:1833]
# ----------------------------------------------------------------------------
# URL of card-server to use, formats are as follows:
#
# newcamd://<username>:<password>@<hostname>:<port>/<des_key>
# aroureos://@<hostname>:<port>
# radegast://@<hostname>:<port>
#
# Example:
# newcamd://foo:[email protected]:12345/0CE3476FF2E1C9D9A0A109B371E3
#
# Multiple card-server url's can be specified for server fail-over.
# If the emu fails to connect or fails to get valid CW's, it will try to
# connect to other servers in a round-robin fashion.
#
# Up to 16 servers can be added from index 0 to 15.
#
# You can choose also to select a cccam or gbox server, but they must be declared
# in the "servers configuration" section ( [Servers] ).
# e.g. : if you want to use a cccam server for a provider you must put it on
# the parameter card_server_url_0=cccam://
# NO MATTER the value after the double slash because server configuration is
# made in the section [Servers].
# Only for newcamd, radegast and aroureos is usefull to put correct connection
# parameters because they are provider dependent.
#
#
# Example i want to use mine card into the slot with newcs for prov 0501 on nagra3 (caid 1833)
card_server_url_0=newcamd://username:[email protected]:10550/0102030405060708091011121314

[Prov:000101:CaID:1810]
# ----------------------------------------------------------------------------
# Multiple card-server url's can be specified for server fail-over.
# If the emu fails to connect or fails to get valid CW's, it will try to
# connect to other servers in a round-robin fashion.
#
# Up to 16 servers can be added from index 0 to 15.
#
# URL of card-server to use, formats are as follows:
#
# newcamd://<username>:<password>@<hostname>:<port>/<des_key>/[EMM]
# aroureos://@<hostname>:<port>/[EMM]
# radegast://@<hostname>:<port>/[EMM]
#
card_server_url_0=newcamd://username:[email protected]:10550/0102030405060708091011121314/EMM
card_server_url_1=newcamd://username:[email protected]:10551/0102030405060708091011121314/EMM
card_server_url_2=newcamd://username:[email protected]:10552/0102030405060708091011121314/EMM

[Prov:000000:CaID:0000]
# this provider is a stand-in for all cards and all caid not declared previously
#
# For example I choose to use cccam protocol on all other provider.
#
card_server_url_0=cccam://<username>:<password>@<hostname>:<port>

########################### servers configuration ############################
[Servers]
#
# This is the section for the multi-server configuration.
#
# URL of card-server to use, formats are as follows:
#
# cccam://<username>:<password>@<hostname>:<port>/<receive_emu_shared>/[EMM]
# where <receive_emu_shared> should assume value "yes" (without quotes, if you like to receive emus data shared by the server) or "no" (this is assumed by default)
#
# gbox://<localhost>:<localport>:<password>@<peer_address>:<peer_port>:<peer_pass>/[EMM]
#
# NOTE: The "EMM" suffix is optional and tells the card-server client whether
# to send EMM's to the card-server or not. Enabling or disabling this only
# has effect if the card-server is configured to accept emms from this client.
#
# NOTE 2: The "card_server_url" is not the same as previously declared in the prov/caid section
# use how many server as you like
#
#card_server_url=cccam://<username>:<password>@<hostname>:<port>
#card_server_url=cccam://<username>:<password>@<hostname>:<port>
 

friedelf

Registered
Messages
1
Has anyone tried this on Kathrein UFS-910 ?
I can connect on my CCcam Server, but there is no picture.
 

sisi1380

Registered
Messages
50
it give me sometimes a message that say "debug level=3"
it is a bit slow in opening channlel on sif r 9047 (e1)
any body has the same problem?

regrads
 

sisi1380

Registered
Messages
50
it give me sometimes a message that say "debug level=3"
it is a bit slow in opening channlel on sif r 9047 (e1)
any body has the same problem?

regrads
 

mpaq99

Registered
Messages
5
Indeed same here on UFS910. Connects to server, get ECM OK but no pic no sound. With Incubus 0.55 no problem... :-(
 

mpaq99

Registered
Messages
5
Unfortunately Incubus 0.7 and 0.75 don't work on Kathrein UFS910 E2 images connecting to CCCam server. Connection is OK and ECM are replied by server with OK, but black screen. With 0.50 amd 0.55 all works OK (but some stability issue with HD channels)... would be great to have Kathrein support fixed if possible.
Thanks Incubus team for great work ! if I can help someone by roviding logs or testing any new version I would be happy yo help. just contact me by PM if I can help ... :thum:
 

aldi99

Registered
Messages
1
also v0.80 doesnt work on Kathrein E2 - no connextion to CCcam server - although incubus is running

Hi,

also the next version v0.80 isn´t working on Kathrein ufs910 E2 together with CCcam server - incubus isn´t connecting to CCcam server at all..

br
aldi
 

Netfreak

Registered
Messages
10
incubuscamd

It is pretty annoying that all versions from incubuscamd do not understand Seca 3. It works only if you kill the daemon and wait for the second package, then it wil decode(wait for appox 30 secs).

Also, the 910HD is not willing to decode Seca 3 with the official CI module and card in enigma2 or original firmware...
sh4 sucks, I think I will buy the original ppc.
 
Top