clone dm800hd cant flash new image stuck on 1%

hi guys need help big time with dm800hd

i flash an image and its never been the same. i think i flashed a currupt image now all i get i 1% when trying to flash new image.

i think my second boot stage config file is corrupt.
i tried to fix with optiflasher
i tried no ca found fix
i tried bootloader fix/update
i tried dreamup too
i tried with ethernet and usb serial cable
i can boot up to first stage and see the lcd screen on my box
1 can see ip address 192.168.1.10 with sim201 #84b lcd: *** STOP ***

but wont go any further until new image is on
i still only get 1% when trying to flash new image via browser or dreamup both clone and normal version or optiflasher 3.0.
on my broswer it uploads image 100% but
i get "Writing to flash memory, please do not turn off power!" but stuck on 1%
i got a log file save of whats going on in my box can someone help?

box dm800hd clone
sim 201
boot loader 84b

The Log file

ðÿü
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.

Dreambox D
FIRST STAGE 1.00 {BO23456}


2ND STAGE OK, build #84 (2011-09-02)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
1.117 - load config
dCA: not existent, loading defaults
1.148 - config loaded.
* press to enter setup
OLED found!
lcd: BOOT #84B
- read config file: /boot/secondstage.conf
detected old jffs2 sig.. disable hw ecc
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . | / - \ | / - \  done.

find_inode failed for name=secondstage.conf

load: Failed to find inode

- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /boot/bootlogo-dm800.elf.gz
bootlogo size: 78479
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <[email protected]>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-2.6.18-7.4-dm800.gz
executing '/boot/vmlinux-2.6.18-7.4-dm800.gz' returned: -2
waiting for link...
link timeout.
lcd: /boot/zImage.elf
find_inode failed for name=zImage.elf

load: Failed to find inode

no valid boot source found. press any key to enter setup.
lcd: *** STOP ***


if anyone know how to fix this issues it would be well appreciated.:thum:

done that am on 84d now still same thing mate. The issues is the second boot load stage i think.

same thing stuck on 1% via web browser , also tried via serial got futher but at the end of over 1.15min still didn't boot to new image still blank so tried again via web browser still stuck at 1% is there a way to instead of flashing to memory can it be flashed to usb stick instead.?

still stuck 1%

am still getting stuck on loading an image i have used dream optiflasher

it loads image at stage 1 boot then when stage 2 kicks in just freezes is there anyway to completely make sure flash directory are in tact or to boot from usb i seen a post saying i might be able to use advance dreambox setting to change boot options? i have some images of what is happening i can get into serial mode.



hope this gives a better picture just gets stuck after uploading image