satelliteman
Registered
- Messages
- 97
SWITCHING THE PATCH OFF/ON
This is needed sometimes if you wish to use other CAM’s or Cards on the receiver:
Press Menu, System Information then enter 2004 on the remote. The CAS and BISS Menus will disappear. To enable the patch again just repeat the process.
You need to have the patch off for your dragon cam to work without problems. Of course you will only be able to view the channels that the dragon is decoding
for premiere or similar portal systems
goto the portal channel ( sport or erotik or direkt )
now press the yellow button and select say 2 x 3 or 3 x 3 etc
the various options will appear in their own windows
use the up/down/left/right to select the required channel ( highighted in blue ) and press OK to choose it
press OK again and you should get the required channel
1. Download to your pc the latest TM loader 1.8.6 or later as required depending on your stb and the bin file from darkman.
2. connect the NULL MODEM serial cable to your pc and stb.
3. Open tm loader 1.8.6 and load /browse the right file.
4. Your stb must have power/switched on from the back (standby mode)
4.Click on connect on the tm loader and power on your TM 1500
Loading starts, wait till it finishes ( writing and erasing)
5. Power off, connect scart or whatever power on
type 2004 in the system information menu and it will switch the patch off
and you can use your cam, reverse to switch it back on
When the Cass & Biss buttons are displayed the patch is On,
and when the patch is Off, they are not displayed
difficulties do arise when using a cam when the patch is active,
you should disable the patch to make the cam & card accessible to the reciever.
Type 2004 in the system information menu and it will switch the patch off and you can use your cam,
reverse to switch it back on.
AES
for Technomate 1000 series use *01* & *11*
make sure you use the correct window as there is 2 for tps 1 for 007c00 other is for aes
as you have noticed there are 2 sets of codes,
the first 16 digits go on the first line and the next 16 digits go on the second line,
when thats done save it,
come out of the cas menu then turn the receiver off for about 30seconds,
then turn it back on,then all should be ok,
remember the keys change everyday.
AES keys for today, opened up CASS and found the TPS section with the four lines,
with as got a mixture of numbers and letters.
I can input the numbers but can't seem to input letters ?
press the a-z button on the remote and set of keys will appear with letters and numbers
If you do a factory reset you will lose all your stored sats and channels
if you do a factory reset it will not wipe the Patch.
you can turn patch On and Off and it will not effect anything you have stored
Go to Menu select system information and just type 2004 to turn patch On or Off
create a favourites list first m8. then you can group them in whatever folder you want to, and rename them
use a NULL MODEM CABLE to connect to your stb , preferably from a proper com port , and not an adapter !!!
Technomate 1000 Series How Too
To Add New Transponder
Press Menu on remote control
Select Installation and press OK
Select Advanced Search press OK
To add new TP press Green button on remote
Select Transponder
Type in new TP Frequency
Select Symbol Rate type in new symbol rate
Select Polarization using right hand arrow key select V or H
Now press Red button to scan for channels on that TP
To Delete a Transponder
Select Menu
Select Installation
Select Advanced Search
Go to Transponder
Select the TP that you wish to delete by using the l/R hand arrow keys
Press Yellow button on remote to delete selected Transponder
To Move Channels
Menu
Select Edit Channels press OK
Select Move Channels press OK
Select the channel you wish to move to new position by pressing OK
Now type in new channel number you want for that channel then press OK when in new position
Or using the left or right hand arrow keys move that channel to new new channel number then press OK. Press Exit then Yes to store in new position
To Delete Channels
Menu
Select Edit Channels press OK
Select Delete Channels press OK
Select the channel.s you wish to delete press OK on that channel
You can select as many channels you wish to delete by pressing OK on the channels
you wish to delete
Press Exit then Yes if you wish to delete the channels
To Change Channel Name
Menu
Select Edit Channels press OK
Then Rename CH/Edit Pids press OK
Select Edit Name press OK
now type in the new name using up/down L/R arrow keys to select the letters
when completed press Exit then Yes to store new name
To Store Satellites
Menu
Installation press OK
Select Satellite Set Up
Select Satellite then using L/R hand keys select the satellite that you want to store
then press Yellow button then press Exit
Select Motorized Settings press OK
Then select DisEQc Motor
Select Transponder and select an active TP
then select 1.2 diseqc or usals using the right arrow key to move dish
Using the 1.2 Diseqc
Select Move by using the left or right arrow key to move dish to get strongest signal
Now go to Save press OK
Press Red button to scan for channels on that satellite
Most tm1000 series remotes now have type 2 (round at the bottom) , the older type 1 is more of a square shape.
You can get a list of satellites, transponders, frequencies, symbol rates and polarizations.
on lyngsat after you have selected the satellite just click the freq. for the TPs Frequency symbol rate
and polarization
Hope this is some help to you
rgds
d+ key entry
Press mute then exit when you are on a D+ channel
It will show you
Nagravision
Digital+(4001) Ohaladin
Indent
10 ** ** ** ** ** ** ** **
11 ** ** ** ** ** ** ** **
add keys , exit and save
reboot the box
or
Press mute then exit when you are on a D+ channel
Once you are on the blank cas page, change from "OFF" to "NAGRA".
Go to the next line and put in the ident "40 01".
On the next line input "10" and use the down key to move to the key position and use numbers 1-9 and "info" button for the letters to enter the new key.
Press down again to go to the next line, enter "11", down again for the key input and enter it.
Once complete press "exit" button, save changes.
Exit to blank screen. Change channel and back again, wait a couple of seconds
type 8280 on the channel to get the biss menu ,then move the bar up and down and select the row you want , the top row is off
now exit and save
Edit/Delete Message
changing the language
press the language button and select one of those presented to you , but remember not all channels have dual audio
also remember the above is for key 00 so for key 01 use the bottom 2 lines , 20 and 21
10.873 V Channels for TPS Au
The following are the channels from which the TPS keys can be updated for Autoupdate using the latest patch dated 13 jul 2007:
France 5
LCP - La Chaîne Parlementaire
M6 Music Rock
M6 Music Black
Equidia
ESPN Classic Sport France
France 4
Ushuaia TV
TV Breizh
France Ô
This is needed sometimes if you wish to use other CAM’s or Cards on the receiver:
Press Menu, System Information then enter 2004 on the remote. The CAS and BISS Menus will disappear. To enable the patch again just repeat the process.
You need to have the patch off for your dragon cam to work without problems. Of course you will only be able to view the channels that the dragon is decoding
for premiere or similar portal systems
goto the portal channel ( sport or erotik or direkt )
now press the yellow button and select say 2 x 3 or 3 x 3 etc
the various options will appear in their own windows
use the up/down/left/right to select the required channel ( highighted in blue ) and press OK to choose it
press OK again and you should get the required channel
1. Download to your pc the latest TM loader 1.8.6 or later as required depending on your stb and the bin file from darkman.
2. connect the NULL MODEM serial cable to your pc and stb.
3. Open tm loader 1.8.6 and load /browse the right file.
4. Your stb must have power/switched on from the back (standby mode)
4.Click on connect on the tm loader and power on your TM 1500
Loading starts, wait till it finishes ( writing and erasing)
5. Power off, connect scart or whatever power on
type 2004 in the system information menu and it will switch the patch off
and you can use your cam, reverse to switch it back on
When the Cass & Biss buttons are displayed the patch is On,
and when the patch is Off, they are not displayed
difficulties do arise when using a cam when the patch is active,
you should disable the patch to make the cam & card accessible to the reciever.
Type 2004 in the system information menu and it will switch the patch off and you can use your cam,
reverse to switch it back on.
AES
for Technomate 1000 series use *01* & *11*
make sure you use the correct window as there is 2 for tps 1 for 007c00 other is for aes
as you have noticed there are 2 sets of codes,
the first 16 digits go on the first line and the next 16 digits go on the second line,
when thats done save it,
come out of the cas menu then turn the receiver off for about 30seconds,
then turn it back on,then all should be ok,
remember the keys change everyday.
AES keys for today, opened up CASS and found the TPS section with the four lines,
with as got a mixture of numbers and letters.
I can input the numbers but can't seem to input letters ?
press the a-z button on the remote and set of keys will appear with letters and numbers
If you do a factory reset you will lose all your stored sats and channels
if you do a factory reset it will not wipe the Patch.
you can turn patch On and Off and it will not effect anything you have stored
Go to Menu select system information and just type 2004 to turn patch On or Off
create a favourites list first m8. then you can group them in whatever folder you want to, and rename them
use a NULL MODEM CABLE to connect to your stb , preferably from a proper com port , and not an adapter !!!
Technomate 1000 Series How Too
To Add New Transponder
Press Menu on remote control
Select Installation and press OK
Select Advanced Search press OK
To add new TP press Green button on remote
Select Transponder
Type in new TP Frequency
Select Symbol Rate type in new symbol rate
Select Polarization using right hand arrow key select V or H
Now press Red button to scan for channels on that TP
To Delete a Transponder
Select Menu
Select Installation
Select Advanced Search
Go to Transponder
Select the TP that you wish to delete by using the l/R hand arrow keys
Press Yellow button on remote to delete selected Transponder
To Move Channels
Menu
Select Edit Channels press OK
Select Move Channels press OK
Select the channel you wish to move to new position by pressing OK
Now type in new channel number you want for that channel then press OK when in new position
Or using the left or right hand arrow keys move that channel to new new channel number then press OK. Press Exit then Yes to store in new position
To Delete Channels
Menu
Select Edit Channels press OK
Select Delete Channels press OK
Select the channel.s you wish to delete press OK on that channel
You can select as many channels you wish to delete by pressing OK on the channels
you wish to delete
Press Exit then Yes if you wish to delete the channels
To Change Channel Name
Menu
Select Edit Channels press OK
Then Rename CH/Edit Pids press OK
Select Edit Name press OK
now type in the new name using up/down L/R arrow keys to select the letters
when completed press Exit then Yes to store new name
To Store Satellites
Menu
Installation press OK
Select Satellite Set Up
Select Satellite then using L/R hand keys select the satellite that you want to store
then press Yellow button then press Exit
Select Motorized Settings press OK
Then select DisEQc Motor
Select Transponder and select an active TP
then select 1.2 diseqc or usals using the right arrow key to move dish
Using the 1.2 Diseqc
Select Move by using the left or right arrow key to move dish to get strongest signal
Now go to Save press OK
Press Red button to scan for channels on that satellite
Most tm1000 series remotes now have type 2 (round at the bottom) , the older type 1 is more of a square shape.
You can get a list of satellites, transponders, frequencies, symbol rates and polarizations.
on lyngsat after you have selected the satellite just click the freq. for the TPs Frequency symbol rate
and polarization
Hope this is some help to you
rgds
d+ key entry
Press mute then exit when you are on a D+ channel
It will show you
Nagravision
Digital+(4001) Ohaladin
Indent
10 ** ** ** ** ** ** ** **
11 ** ** ** ** ** ** ** **
add keys , exit and save
reboot the box
or
Press mute then exit when you are on a D+ channel
Once you are on the blank cas page, change from "OFF" to "NAGRA".
Go to the next line and put in the ident "40 01".
On the next line input "10" and use the down key to move to the key position and use numbers 1-9 and "info" button for the letters to enter the new key.
Press down again to go to the next line, enter "11", down again for the key input and enter it.
Once complete press "exit" button, save changes.
Exit to blank screen. Change channel and back again, wait a couple of seconds
type 8280 on the channel to get the biss menu ,then move the bar up and down and select the row you want , the top row is off
now exit and save
Edit/Delete Message
changing the language
press the language button and select one of those presented to you , but remember not all channels have dual audio
also remember the above is for key 00 so for key 01 use the bottom 2 lines , 20 and 21
10.873 V Channels for TPS Au
The following are the channels from which the TPS keys can be updated for Autoupdate using the latest patch dated 13 jul 2007:
France 5
LCP - La Chaîne Parlementaire
M6 Music Rock
M6 Music Black
Equidia
ESPN Classic Sport France
France 4
Ushuaia TV
TV Breizh
France Ô