TNT Sat - Oscam + CCCam

flausina

Registered
Messages
9
Hi

I got a TNT Sat Card but I can't get work with "oscam10777+cccam213"

I try many configuration, now I got this

---------------------------------------------
Oscam.conf

[global]
logfile = stdout;/tmp/oscam.log
nice = -1
maxlogsize = 256

[cache]

[newcamd]
port = 15000@0500:0030B0
key = 0102030405060708091011121314

[dvbapi]
enabled = 1
au = 1
user = localuser
boxtype = dreambox

[webif]
httpport = 16002
httpallowed = 127.0.0.1,192.168.0.0-192.168.1.255
-----------------------------------------------
oscam.server

[reader]
label = tntsat
protocol = internal
device = /dev/sci0
detect = cd
mhz = 450
cardmhz = 2700
aeskeys = 0500@ xxxxxxxxxxx
group = 1
emmcache = 1,3,2,0
--------------------------------------------------
oscam.user

[account]
user = tntsat
pwd = viacrypt
caid = 0500
keepalive = 1
au = 1
group = 1
ident = 0500:030B00

[account]
user = anonymous
group = 1
----------------------------------------------------
oscam.dvbapi
Code:
#----------------------------------------#
# TNTSAT EMU (19.2E) (0500:030B00) 29.07.2013
# delete these lines, when you don't use TNTSat EMU !!!
#
P: 0500:030B00:2329 1 ; TF1 HD 
P: 0500:030B00:233D 1 ; TF1 HD  
P: 0500:030B00:2351 1 ; TF1 HD 
P: 0500:030B00:245E 1 ; M6 HD 
P: 0500:030B00:2486 1 ; M6 HD  
P: 0500:030B00:2472 1 ; M6 HD   
P: 0500:030B00:2462 1 ; FRANCE 2 HD    
P: 0500:030B00:2476 1 ; FRANCE 2 HD   
P: 0500:030B00:248A 1 ; FRANCE 2 HD   
P: 0500:030B00:2458 1 ; ARTE HD  
P: 0500:030B00:246C 1 ; ARTE HD   
P: 0500:030B00:2480 1 ; ARTE HD   
P: 0500:030B00:6F73 1 ; Cherie25  
P: 0500:030B00:6F86 1 ; Cherie25 
P: 0500:030B00:6F87 1 ; Cherie25 
#                                
I: 0500:030B00:2206:0443 ; TF1     
P: 0500:030B00:2206:043E 1 ; TF1   
I: 0500:030B00:221A:0443 ; TF1     
P: 0500:030B00:221A:043E 1 ; TF1    
I: 0500:030B00:2202:02B3 ; M6     
P: 0500:030B00:2202:02AE 1 ; M6    
I: 0500:030B00:2216:02B3 ; M6  
P: 0500:030B00:2216:02AE 1 ; M6        
I: 0500:030B00:2218:037B ; W9             
P: 0500:030B00:2218:0376 1 ; W9                                                 
I: 0500:030B00:2204:037B ; W9     
P: 0500:030B00:2204:0376 1 ; W9  
I: 0500:030B00:2013:04A8 ; TMC
P: 0500:030B00:2013:04A9 1 ; TMC
I: 0500:030B00:2027:04A8 ; TMC
P: 0500:030B00:2027:04A9 1 ; TMC
I: 0500:030B00:2011:03E0 ; FRANCE 2
P: 0500:030B00:2011:03DA 1 ; FRANCE 2
I: 0500:030B00:2025:03E0 ; FRANCE 2
P: 0500:030B00:2025:03DA 1 ; FRANCE 2
I: 0500:030B00:2024:037C ; FRANCE 3
P: 0500:030B00:2024:0379 1 ; FRANCE 3
I: 0500:030B00:2010:037C ; FRANCE 3
P: 0500:030B00:2010:0379 1 ; FRANCE 3
I: 0500:030B00:2213:0188 ; FRANCE 4
P: 0500:030B00:2213:0185 1 ; FRANCE 4
I: 0500:030B00:21FF:0188 ; FRANCE 4
P: 0500:030B00:21FF:0185 1 ; FRANCE 4
I: 0500:030B00:2214:01EC ; FRANCE 5
P: 0500:030B00:2214:01E9 1 ; FRANCE 5
I: 0500:030B00:2200:01EC ; FRANCE 5
P: 0500:030B00:2200:01E9 1 ; FRANCE 5
I: 0500:030B00:21FE:0124 ; FRANCE O
P: 0500:030B00:21FE:0121 1 ; FRANCE O
I: 0500:030B00:2212:0124 ; France O
P: 0500:030B00:2212:0121 1 ; France O
I: 0500:030B00:2219:03E0 ; GULLI
P: 0500:030B00:2219:03DE 1 ; GULLI
I: 0500:030B00:2205:03E0 ; GULLI
P: 0500:030B00:2205:03DE 1 ; GULLI
I: 0500:030B00:4284:1789 ; NT1
P: 0500:030B00:4284:1788 1 ; NT1
I: 0500:030B00:4290:1789 ; NT1
P: 0500:030B00:4290:1788 1 ; NT1
I: 0500:030B00:2211:00C0 ; D8
P: 0500:030B00:2211:00BA 1 ; D8
I: 0500:030B00:21FD:0022 ; D8
P: 0500:030B00:21FD:00BA 1 ; D8
I: 0500:030B00:200E:02B4 ; NRJ 12
P: 0500:030B00:200E:02AE 1 ; NRJ 12
I: 0500:030B00:2022:02B4 ; NRJ 12
P: 0500:030B00:2022:02AE 1 ; NRJ 12
I: 0500:030B00:275F:0FEF ; RMC Decouverte
P: 0500:030B00:275F:0FEA 1 ; RMC Decouverte
I: 0500:030B00:2761:0FEF ; RMC Decouverte
P: 0500:030B00:2761:0FEA 1 ; RMC Decouverte
I: 0500:030B00:2136:19E2 ; NUMERO 23
P: 0500:030B00:2136:19DC 1 ; NUMERO 23
I: 0500:030B00:217C:19E2 ; NUMERO 23
P: 0500:030B00:217C:19DC 1 ; NUMERO 23
P: 0500:030B00:189F 1 ; L EQUIPE 21
P: 0500:030B00:18B3 1 ; L EQUIPE 21
#
I: 0500:030B00:25E5:1975 ; F3 PICARDIE
P: 0500:030B00:25E5:196E 1 ; F3 PICARDIE
I: 0500:030B00:25E6:19E3 ; F3 FRANCHE COMTE
P: 0500:030B00:25E6:19DC 1 ; F3 FRANCHE COMTE
I: 0500:030B00:25E7:1989 ; F3 AQUITAINE
P: 0500:030B00:25E7:1982 1 ; F3 AQUITAINE
I: 0500:030B00:2649:1975 ; F3 BNORMANDIE
P: 0500:030B00:2649:196E 1 ; F3 BNORMANDIE
I: 0500:030B00:25E9:199D ; F3 AUVERGNE
P: 0500:030B00:25E9:1996 1 ; F3 AUVERGNE
I: 0500:030B00:264D:199D ; F3 BOURGOGNE
P: 0500:030B00:264D:1996 1 ; F3 BOURGOGNE
I: 0500:030B00:2650:1A1F ; F3 ALPES
P: 0500:030B00:2650:1A18 1 ; F3 ALPES
I: 0500:030B00:2651:19C5 ; F3 NORD PDC
P: 0500:030B00:2651:19BE 1 ; F3 NORD PDC
I: 0500:030B00:25ED:19C5 ; F3 LIMOUSIN
P: 0500:030B00:25ED:19BE 1 ; F3 LIMOUSIN
I: 0500:030B00:25EE:1A3D ; F3 RHONE ALPES
P: 0500:030B00:25EE:1A36 1 ; F3 RHONE ALPES
I: 0500:030B00:25EF:1AAB ; F3 PROV ALPES
P: 0500:030B00:25EF:1AA4 1 ; F3 PROV ALPES
I: 0500:030B00:2653:1AAB ; F3 LANGUEDOCROU
P: 0500:030B00:2653:1AA4 1 ; F3 LANGUEDOCROU
I: 0500:030B00:25E8:19F7 ; F3 LORRAINE
P: 0500:030B00:25E8:19F0 1 ; F3 LORRAINE
I: 0500:030B00:264A:19E3 ; F3 PAYS DE LOIRE
P: 0500:030B00:264A:19DC 1 ; F3 PAYS DE LOIRE
I: 0500:030B00:264B:1989 ; F3 COTE D'AZUR
P: 0500:030B00:264B:1982 1 ; F3 COTE D'AZUR
I: 0500:030B00:264C:19F7 ; F3 CENTRE
P: 0500:030B00:264C:19F0 1 ; F3 CENTRE
I: 0500:030B00:25EA:1A0B ; F3 PARIS IDF
P: 0500:030B00:25EA:1A04 1 ; F3 PARIS IDF
I: 0500:030B00:264E:1A0B ; F3 POITOUCHAR
P: 0500:030B00:264E:1A04 1 ; F3 POITOUCHAR
I: 0500:030B00:264F:19B0 ; F3 CHAMP ARDENNE
P: 0500:030B00:264F:19AA 1 ; F3 CHAMP ARDENNE
I: 0500:030B00:25EB:19B1 ; F3 BRETAGNE
P: 0500:030B00:25EB:19AA 1 ; F3 BRETAGNE
I: 0500:030B00:25EC:1A1F ; F3 HNORMANDIE
P: 0500:030B00:25EC:1A18 1 ; F3 HNORMANDIE
I: 0500:030B00:2652:1A3D ; F3 ALSACE
P: 0500:030B00:2652:1A36 1 ; F3 ALSACE
I: 0500:030B00:25F0:1A51 ; F3 MIDI PYRENEES
P: 0500:030B00:25F0:1A4A 1 ; F3 MIDI PYRENEES
I: 0500:030B00:2654:1A51 ; F3 CORSEVIASTELL
P: 0500:030B00:2654:1A4A 1 ; F3 CORSEVIASTELL
#
P: 0500:030B00:1FAD ; PARIS PREMIERE (some hours only) ???
#
#I: 0500:030B00 # ignore 030B00 on all other channels
#
#---------------------------------------#

CCCam Line in cccam.cfg

N: 127.0.0.1 15000 tntsat viacrypt 01 02 03 04 05 06 07 08 09 10 11 12 13 14
C: [My private CLine]
----------------------------------------------------

- The Aeskeys are correct.

If I start on TNTSat only see tntsat channels by card I try to see other channels with cccam but i can't, the server is on but no EMM.
If I start with CCCam i see all channels with cam but the card don't work.

What I Can do?
Can I config the cccam.prio to work with card?
 

kalehrl

Registered
Messages
147
Why not just use oscam?
CCcam is not necessary and it just complicates setup without bringing anything to the table. Even though CCcam 2.3.0 supports long ECMs, it frequently just dies when switching to a TNT Sat channel and you have to start it again. Here is my oscam config:
oscam.conf:
Code:
[global]
logfile                       = stdout
waitforcards                  = 0

[dvbapi]
enabled                       = 1
user                          = localuser
boxtype                       = dreambox

[webif]
httpport                      = 16004
httprefresh                   = 10
httpallowed                   = 127.0.0.1,192.168.0.0-192.168.255.255
oscam.server:
Code:
[reader]
label                         = tntsat
protocol                      = internal
device                        = /dev/sci0
caid                          = 0500
detect                        = cd
mhz                           = 450
cardmhz                       = 2700
ident                         = 0500:030B00,FFF400
aeskeys                       = 0500@030B00:0,0,0,0,0,0,0,0,0,0,0,0,0,2504B382B16D8C6758DB960E311E9351,0,0,0,F62C3BE300E98BBB378DFA38BB6EEEF1,0,0,6B1B024D36F60974973CB81FA5E8F01C,0,0,1DE5B042AD670BB16A3A76BDAD2F7AC0
group                         = 1
oscam.user:
Code:
[account]
user                          = localuser
group                         = 1
oscam.dvbapi:
Code:
P: 0500:030B00:2013:04A9 # TMC
P: 0500:030B00:2027:04A9 # TMC
The card is activated using ECM, not EMM so you don't need EMMs at all! My card also wouldn't receiver a single EMM.
 

percivjr

Registered
Messages
461
What I Can do?

I couldn't get CCcam to connect using newcamd protocol (I'm using doscam v.025 and CCcam 2.3.0) with my TNT card.

I suggest you delete [newcamd] server from oscam.conf and replace it with a [cccam] server.

Then in CCcam.cfg, delete your N: line and replace it with:
C: 127.0.0.1 15000 tntsat viacrypt yes

Start oscam first, then CCcam.

Good luck.
 

magictails

Registered
Messages
428
hi

my setting with tntsat card v5 + doscam 0.25 E2 800HD
emu is not active

card ok ; cs ok :



[global]
nice = -19
logfile = stdout
disablelog = 1
#usrfile = /tmp/oscamuser.log
lb_save = 0
zeroconf = 0

[dvbapi]
pmt_mode = 1
user = localuser
boxtype = dreambox

[monitor]
nocrypt = 127.0.0.1,10.0.0.0-10.255.255.255,172.16.0.0-172.31.255.255,192.168.0.0-192.168.255.255
hideclient_to = 15

[webif]
httpport = 16001
httprefresh = 30
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
hideclient_to = 15


[reader]
label = tntsat
enable = 1
protocol = internal
device = /dev/sci0
services = tntsat
caid = 0500
ident = 0500:030B00
detect = cd
mhz = 357
cardmhz = 357
group=1
aeskeys = 0500@030B00:0,F1DCB15

doscam.cfg

[tntsat]
caid = 0500
provid = 030B00
srvid = 1F49,19D0,20D6,2136,219C,219D,219F,21A1,2239,232B,2330,245A,245C,245D,2457,2458,275F,6F73,7A4D,
 
Last edited:

magictails

Registered
Messages
428
my setting with tntsat card v5
Oscam 1.20 rev 148 E2 800HD
emu is not active

card ok ; cs ok :

[global]
logfile = /tmp/logfile
clientmaxidle = 1500
failbantime = 14400
cachedelay = 120
netprio = 1
nice = -1
maxlogsize = 20
preferlocalcards = 1
saveinithistory = 1
readerrestartseconds = 1
dropdups = 1
lb_mode = 1
lb_save = 100
lb_stat_cleanup = 12
lb_savepath = /tmp/stat
lb_reopen_mode = 1
audisabled = 0

[cache]
cwcycle_check_enable = 1
cwcycle_check_caid = 0100,0500,0603,0604,0608,0622,0628,0B00,0B01,0B02, 0BAA,0D00,0D02,0D0F,0D95,0D96,1702,1722,1802,1803, 1810,1833,1834,183D,1843,1880,4AEE,5581
cwcycle_maxlist = 4000
cwcycle_keeptime = 15
cwcycle_onbad = 1
cwcycle_dropold = 1
cwcycle_sensitive = 3
max_time = 10
max_count = 7500
wait_time = 300
csp_port = 11000
csp_allow_reforward = 1

[monitor]
port = 700
nocrypt = 127.0.0.1,192.168.0.0-192.168.255.255
aulow = 120
hideclient_to = 15
monlevel = 4
appendchaninfo = 1

[newcamd]
port = 10000@0500:030B00
key = 0102030405060708091011121314

#[cccam]
#port = 12000
#reshare = 1
#version = 2.2.1
#stealth = 1

[dvbapi]
enabled = 1
au = 1
pmt_mode = 1
boxtype = dreambox
user = localuser

[webif]
httpport = 16001
httphelplang = fr
httpuser = oscam
httppwd = admin
httprefresh = 30
httpallowed = 127.0.0.1,192.168.1.1-192.168.1.255
Http tpl= /etc/tuxbox/config

[anticasc]
enabled = 1
numusers = 1
sampletime = 5
samples = 2
penalty = 1
#aclogfile = /var/log/aclogfile
denysamples = 2
fakedelay = 1000
 

valentino50

Registered
Messages
907
Why not just use oscam?
CCcam is not necessary and it just complicates setup without bringing anything to the table. Even though CCcam 2.3.0 supports long ECMs, it frequently just dies when switching to a TNT Sat channel and you have to start it again. Here is my oscam config:
oscam.conf:
Code:
[global]
logfile                       = stdout
waitforcards                  = 0

[dvbapi]
enabled                       = 1
user                          = localuser
boxtype                       = dreambox

[webif]
httpport                      = 16004
httprefresh                   = 10
httpallowed                   = 127.0.0.1,192.168.0.0-192.168.255.255
oscam.server:
Code:
[reader]
label                         = tntsat
protocol                      = internal
device                        = /dev/sci0
caid                          = 0500
detect                        = cd
mhz                           = 450
cardmhz                       = 2700
ident                         = 0500:030B00,FFF400
aeskeys                       = 0500@030B00:0,0,0,0,0,0,0,0,0,0,0,0,0,2504B382B16D8C6758DB960E311E9351,0,0,0,F62C3BE300E98BBB378DFA38BB6EEEF1,0,0,6B1B024D36F60974973CB81FA5E8F01C,0,0,1DE5B042AD670BB16A3A76BDAD2F7AC0
group                         = 1
oscam.user:
Code:
[account]
user                          = localuser
group                         = 1
oscam.dvbapi:
Code:
P: 0500:030B00:2013:04A9 # TMC
P: 0500:030B00:2027:04A9 # TMC
The card is activated using ECM, not EMM so you don't need EMMs at all! My card also wouldn't receiver a single EMM.
Hi mate would that work on Newnigma2 image on DM800se clone and does this config opens all TNT sd and hd channels.
Regards
 

kalehrl

Registered
Messages
147
Hi mate would that work on Newnigma2 image on DM800se clone and does this config opens all TNT sd and hd channels.
It works in all images and it opens sd as well as hd channels.
 

valentino50

Registered
Messages
907
It works in all images and it opens sd as well as hd channels.
Thanks for your response. One more question if you dont mind.
would it be possible to activate a new TNTsat card via DM800se or do i have to activate it via an official TNTSAT box?
Regards
 

valentino50

Registered
Messages
907
Thanks for both replies.
I have a strange problem .
All tntsat card channels work fine when using Oscam.But when changing CCcam to use CS line while the card is still inserted few channels like(TF1.FRANCE2.FRANCE3.M6 SD) does not open with cccam cs line
Any help would be appreciated
 
Last edited:

kalehrl

Registered
Messages
147
I think it has something to do with incorrect ECM pid being used. It sometimes happens with oscam so oscam.dvbapi needs to be set correctly. Have a look at oscam.dvbapi I posted a couple of posts before. I don't know how to do it in CCcam.
 

valentino50

Registered
Messages
907
Thanks for your reply. The problem rely only to TNTsat SD channels which can not be open using Cccam line when the TNTsat card is in the slot where as the HD channels are open ??? weird:confused:
 
Last edited:

flausina

Registered
Messages
9
Thanks

I Change my CCCam Line to work on Oscaam

EX
C: theserver 25000 user pass

Oscam.server
[reader]
label = Myline
protocol = cccam
device = theserver,25000
user = user
password = pass
inactivitytimeout = 30
group = 1
cccversion = 2.2.1 # I use the version showing on cccam webinterface
cccmaxhops = 2
ccckeepalive = 1
cccreshare = 1


So far so good

I can read the card and use the cline at the same time

Thanks again
 

valentino50

Registered
Messages
907
Thanks

I Change my CCCam Line to work on Oscaam

EX
C: theserver 25000 user pass

Oscam.server
[reader]
label = Myline
protocol = cccam
device = theserver,25000
user = user
password = pass
inactivitytimeout = 30
group = 1
cccversion = 2.2.1 # I use the version showing on cccam webinterface
cccmaxhops = 2
ccckeepalive = 1
cccreshare = 1


So far so good

I can read the card and use the cline at the same time

Thanks again
At last someone came with decent clear explanation.:thum:
Thank you so much Flausina very much appreciated.:clapping:
One more question if you dont mind what if we have more then one Cccam line i mean 3 or 4 how do we add them?
Regards
 

percivjr

Registered
Messages
461
if we have more then one Cccam line i mean 3 or 4 how do we add them?
Regards


Do you mean in CCcam.cfg? If so just do this:

C: theserver1 25001 user1 pass1
C: theserver2 25002 user2 pass2
C: theserver3 25003 user3 pass3
C: theserver4 25004 user4 pass4
 

valentino50

Registered
Messages
907
Do you mean in CCcam.cfg? If so just do this:

C: theserver1 25001 user1 pass1
C: theserver2 25002 user2 pass2
C: theserver3 25003 user3 pass3
C: theserver4 25004 user4 pass4
Hi there i meant adding more then one Cline in Oscam server
 

flausina

Registered
Messages
9
CCcam.cfg
C: theserver1 25001 user1 pass1
C: theserver2 25002 user2 pass2
C: theserver3 25003 user3 pass3
C: theserver4 25004 user4 pass4

CCam.cfg GOES TO Oscam.server

Oscam.server
[reader]
label = Myline1
protocol = cccam
device = theserver1,25001
user = user1
password = pass1
inactivitytimeout = 30
group = 1
cccversion = 2.2.1 # I use the version showing on cccam webinterface
cccmaxhops = 2
ccckeepalive = 1
cccreshare = 1

[reader]
label = Myline2
protocol = cccam
device = theserver2,25002
user = user2
password = pass2
inactivitytimeout = 30
group = 1
cccversion = 2.2.1 # I use the version showing on cccam webinterface
cccmaxhops = 2
ccckeepalive = 1
cccreshare = 1

[reader]
label = Myline3
protocol = cccam
device = theserver3,25003
user = user3
password = pass3
inactivitytimeout = 30
group = 1
cccversion = 2.2.1
cccmaxhops = 2
ccckeepalive = 1
cccreshare = 1

[reader]
label = Myline4
protocol = cccam
device = theserver4,25004
user = user4
password = pass4
inactivitytimeout = 30
group = 1
cccversion = 2.2.1
cccmaxhops = 2
ccckeepalive = 1
cccreshare = 1
 
Top