Manual Installation of the Image "OPENPLI TDT HISPASAT" in QVIART LUNIX y QVIART LUNIX3 4K

Tupiton

Registered
Messages
217
Manual Installation of the Image "OPENPLI TDT HISPASAT" in QVIART LUNIX y QVIART LUNIX3 4K

1. We must download the image "Qviart Linux Openpli Hispasat 09-07-18", any of the following links:

> Link to download the image for Qviart LUNIX:
Code:
https://mega.nz/#!8XoTSC4a!Y7TqbRYMTYt5DzmIz-Gy6ZfA_ZC3YDvKnziBBA4FREU
Code:
http://upload.dvhk.to/file.php?id=18720
Code:
http://dvb-upload.com/index.php?action=download&pid=389732

> Link to download the image for Qviart LUNIX3 4K:
Code:
https://mega.nz/#!8aoBQIgQ!Y7TqbRYMTYt5DzmIz-Gy6ZfA_ZC3YDvKnziBBA4FREU
Code:
http://upload.dvhk.to/file.php?id=18727
Code:
http://dvb-upload.com/index.php?action=download&pid=389733

2. After download we observed that the downloaded image is a .zip file, which we will unzip. Once unzipped this .zip file we Will see that a folder named with the same name "Qvairt Lunix Openpli Hispasat 09-07-18" or "Qvairt Lunix3 4K Openpli Hispasat 09-07-18", we must enter inside this folder where we will see that there is another folder called "UPDATE" which we must copy such which is in the root of the USB device (previously formatted in FAT32).

3. With the receiver turned on we must insert this USB device (with the "UPDATE" folder in its root) in some of the decoder's slots.

4. Once inserted the USB we must go to the Menu / Standby-restart and select the option to restart.

5. Once we see that the receiver is going to restart we will appear a screen where it tells us that a new firm has been found and that we must keep pressing the Power button (Red) on the remote control so that the receiver can read the USB and that way to install the image.

6. While the image is being installed, a screen will appear indicating that the image is being installed and we should wait for it to finish.

7. Once the image is installed, the receiver will restart, and the start configuration menu will appear, to configure our decoder, these are the steps to follow for the configuration:
- Step 1 "Video Input selection": we must select the "HDMI" option.
- Step 2 "Video Mode Selection": we can select any option but the most recommended is the "1080p" or "1080i"
- Step 3 "Select idiom": you must choose the idiom that you want in your receiver menu.
- Step 4 "Calibrate the remote control": just let the 10 seconds of wait pass.
- Step 5 "Set the wizard": you can exit the wizard or configure it (by selecting the option "Use the wizard to set up basic features")
- Step 6 "Check the internet connection": select this option to check your internet.
- Step 7 "Skip internet connection check": we must configure the tuners (leave as configured), press "OK" and it will tell you if you want to make a channel search, if you do not want to make it, click on the "NO" option.
Following these steps, you have the receiver configured and ready to work.

8. Once the image is installed and the receiver is configured, we must restart the receiver again from Enigma2 (Menu / Standby-Subtract / Restart).

9. After the restart we can see that TDT HISPASAT channels are already installed.

10. To go to the list of TDT HISPASAT channels there are two options:
- The first option, press the "SAT" button on the remote control, select the folder "30.0.W Hispasat 30W-4 / 30W-5- Channels" and press the "OK" button on the remote control to enter, once inside the channel list will appear and we simply have to select with the "OK" button of the command that channel we want to see.
- The second option, press the "PROV" button on the remote control, select the folder "ALBERTIS" (the folder with the caps letters) and press the "OK" button on the remote control to enter, once inside the channel list will appear and we simply must select with the "OK" button of the command that channel we want to see.

11. If we want to open a channel and we see that it does not open it, we just have to wait in the channel (to generate the key) about 20 seconds or so and change the channel. This usually happens if the deco is a long time off.
 

EnoSat

Senior Member
Messages
1,952
tested update LUNIX3 4K or only CTRL+C / CTRL+P ?
 
Last edited:

Tupiton

Registered
Messages
217
Sorry, but this MANUAL and IMAGE only work for QVIART LUNIX.

NOT work for QVIART LUNIX3 4K
 

Ramboide

Registered
Messages
202
Into file "Qviart Lunix Openpli Emu SRG Hotbird 13 + Emu DVB-T Spain Hispasat 30 (8.8.18)", after be uncompressed, there is a file named "READ PLEASE.txt" that says:
This image has special Oscam as default. You can download from plugings menu the oficial one, in case you want.
As LNB1 is designated to Hispasat 30W in Tuner Configuration, SRG or other channels need to be set other LNBs besides LNB1.
And please be noted Factory Reset will delete BISS channels. Please re-install the image in that case.
Can this oscam be adapted for other receivers? This is only for the HD Qviart, not the UHD one, so might be necessary make changes for adapt this, such as the script of "Astra-sm", that make this work with the decoders UHD with ARM chip.
 
Last edited:
Top