Zgemma h9s Dead-Bricked

jetika

Registered
Messages
3
I make fullback up and tray flash with this !All is gone ok!After 4 min.Is zgemma restart and not alive again!Only white light!I try contact with factory about bootloader and instruction have-have!But not successful.Zgemma h9s is great reciver!Kodi work fantastic,udpxy too..Iptv super!But now is dead!
PLEASE HELP ME????
 

LilleMama

Registered
Messages
283
Hello, guys!


I tortured mine a little bit too much, apparently...
laugh.gif
It gave up...


So, now it seems I may need the following:





-Download HiTool (tool for rs232) here: https://mega.nz/#!0zRERTAC!HbM…bmI1Uo7D9BcWFDWheGCAQq4GA


A newer version 5.06 is here: https://archive.org/download/HiToolSTB5.0.6


You need the appropriate cable and for this box the connectors are on the motherboard itself, so open it up and connect only (my case below: https://www.adafruit.com/product/954 ):


grd (black)
rx (white)
tx (green)





More here:
: https://www.youtube.com/watch?v=WXCfOUSguGQ]


Also: https://jb8a8f8.com/support/in…icked-boxes-recovery.510/ - thanx to Raza05!


WARNING!!! BE CAREFUL, THESE DEVICES DIFFER IN TERMS OF
NAND or

eMMC
etc.



H9S has Hi3798MV200 Main chipset

These settings and files might not be for your machine!!! It seems like a lot of experimenting should go on, as I could not see anything PRECISE and EXHAUSTIVE on the net... It seems I must dig into this...



More help here: https://rickcaylor.websitetool…-brick-my-sf8008-10299227


https://jb8a8f8.com/support/in…ad-zgemma-h92h.542/page-2

"Zgemma h9s alive again! Have? Simple ! hitool (tool for rs232)!You must have driver for hi3798v200-Important! Normaly conection with rs232(in the Mother.B. is conector)You conect only rx-tx-grd...!You put in hiburn- fastboot.bin and only burn! Thanks a loot for Zgemma support.Are have some problem ,i like help!Thanks Openatv forum! Hansmayer!"





Good luck to us all... I have to try this myself, later on today.


Thanks to Gorski for the original post
 

alpes

Registered
Messages
2
I also had the problem that the box does not start, leaving only the light / logo white.
I tried to flash a new image with a USB stick by placing it on the USB 3.0 port and it never worked. I decided to switch to port 2.0 and work on the first try.
I hope it helps others in the same situation.
Compliments.
 

TurboPirate

Registered
Messages
60
Hello, guys!


I tortured mine a little bit too much, apparently...
laugh.gif
It gave up...


So, now it seems I may need the following:





-Download HiTool (tool for rs232) here: https://mega.nz/#!0zRERTAC!HbM…bmI1Uo7D9BcWFDWheGCAQq4GA


A newer version 5.06 is here: https://archive.org/download/HiToolSTB5.0.6


You need the appropriate cable and for this box the connectors are on the motherboard itself, so open it up and connect only (my case below: https://www.adafruit.com/product/954 ):


grd (black)
rx (white)
tx (green)





More here:
: https://www.youtube.com/watch?v=WXCfOUSguGQ]


Also: https://jb8a8f8.com/support/in…icked-boxes-recovery.510/ - thanx to Raza05!


WARNING!!! BE CAREFUL, THESE DEVICES DIFFER IN TERMS OF
NAND or
eMMC

etc.



H9S has Hi3798MV200 Main chipset

These settings and files might not be for your machine!!! It seems like a lot of experimenting should go on, as I could not see anything PRECISE and EXHAUSTIVE on the net... It seems I must dig into this...



More help here: https://rickcaylor.websitetool…-brick-my-sf8008-10299227


https://jb8a8f8.com/support/in…ad-zgemma-h92h.542/page-2

"Zgemma h9s alive again! Have? Simple ! hitool (tool for rs232)!You must have driver for hi3798v200-Important! Normaly conection with rs232(in the Mother.B. is conector)You conect only rx-tx-grd...!You put in hiburn- fastboot.bin and only burn! Thanks a loot for Zgemma support.Are have some problem ,i like help!Thanks Openatv forum! Hansmayer!"





Good luck to us all... I have to try this myself, later on today.


Thanks to Gorski for the original post
Where is the driver hi3798v200 to make this work? My H9S is dead only white led on I have tried the hitool but the driver you mentioned is no where to be found, why not upload here?
 
Top